Search Documents

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Part III reviewed the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona. Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and a P80 of 6 to 7 µm), pressure leaching at 160ºC with 1,380 kPa (200 psig) oxygen overpressure, DEW to produce LME Grade A cathode, recycling some of the lean electrolyte to the pressure leaching step, and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an acid-autogenous process for pressure leaching. This paper (Part IV) discusses the development and design of a full-scale commercial application for the Morenci operation in Arizona.

Jan 1, 2007

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By Phil Keele

Canadian Natural ??Business Approach Efficiency and Execution ?Drive to be the low cost producer ?Focus on exploitation ?Augment exploitation with strategic acquisitions ?Maintain Discipline and Strength while Delivering on the Defined Plan ?Maintain flexibility and control allocation of capital ?Strive for balance (asset portfolio) ?Maintain financial strength

May 1, 2010

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By Rob Morrison, Peter Cameron

"Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised.In 1970 Alban Lynch promoted two practical ideas to improve plant operations:• Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie. to design and to optimise) complete mineral processing circuits.• Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant.Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation.Models of comminution and classification developed at the JKMRC have been used since the early 1980's. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill® projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product.JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry.They include:• Commercial software (JKSimMet, JKSimBlast and JKMetAccount).• Monographs (Comminution and Blasting).• Technologies (Mine-to-Mill® and flotation optimisation).• Hardware products (JKFrothCam, JKJetLift® and the Mineral Liberation Analyser).This paper summarises these technologies and their benefits."

Jan 1, 2003

Recovery of Pentlandite and Chalcopyrite from Tailings by Bi-Cyclone Powerful Flotation Column

Sep 13, 2010

By Orlando Gallardo

El presente texto describe la implementación del software ADS (Sistema de Despliegue Activo) a los sistemas de control supervisor de los diferentes procesos del complejo metalúrgico a nivel administrativo -en tanto replica los archivos gráficos y de base de datos. Este servidor además de concentrar en su red de campo redundante data de controladores e instrumentos de campo, puede compartir información con clientes usuarios y clientes de visualización dentro de la planta. En ese sentido, el objetivo es simplificar la producción y uso de datos únicos y garantizar la fiabilidad de estos a tiempo real para todos los niveles de supervisión a nivel administrativo, al tiempo que se planea y optimiza los recursos con la toma de decisiones apropiada.

Sep 24, 2008

CSIRO Mineral has recently developed a new electron microprobe based system for characterizing zircon grains from heavy minerals sand deposits. The system acquires cathodoluminescence (CL) spectra, X-ray and backscattered electron (BSE) signals in parallel. By scanning over a specified target area, CL wavelength and X-ray element distribution maps of polished zircon grains can be acquired. Post-inspection of the combined dataset using in-house developed software enables correlations between chemistry and structure to be investigated. The new method offers significant benefits over traditional CL and BSE techniques in that direct comparison with the elemental concentrations over the same region is now achievable. By combining the electron microprobe results with data for the same mapped region obtained via a nuclear microprobe, significantly better detection limits (~ 1ppb) for elements with atomic numbers greater than iron are possible. The ability to measure spatially related analytical data and then investigate the correlation of the CL spectra with chemical data is an important advancement in the characterization of zircons. Key words: zircon, characterization, cathodoluminescence, backscattered electron, electron microprobe, nuclear microprobe, chimage, proton induced x-ray emission.

Jan 1, 2003

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By M. Baumann

Introduction Gold Quarry is one of the largest gold deposits in Nevada, located along the Carlin Trend, approximately seven miles north of Carlin, NV. Owned and operated by Newmont Mining Corporation, as of December 31, 2005, Gold Quarry had produced over 13 million ounces of gold. Multiple simulations were constructed for gold and metallurgical variables using the Stepwise Conditional Transformation method. Analyses of these simulations have been used for a variety of purposes, including an assessment of uncertainty with various ore types. This assessment provides insight for improved modeling and reconciliation. Geological Framework Gold Quarry is a large, low-grade disseminated gold deposit hosted in Silurian-Devonian aged sediments at the Chukar/Alunite-Good Hope fault intersection. Gold bearing hydrothermal fluids appear to have migrated upwards along the Chukar/Alunite and Deep Sulfide Feeder faults and then moved outward along favorable stratigraphic horizons and structural intersections.

Jan 1, 2007

By P. J. Brereton-Stiles, C. J. Hockaday, I. J. Barker, M. S. Rennie

This paper reports on studies that have been done on the electrical conduction in silicon, ferro silicon, and charge chrome furnaces. A system has been developed that can distinguish between normal resistive conduction and arcing, and this was used to quantify in particular the relative amount of arcing that takes place in these furnaces. It was found that silicon and ferro silicon behave similarly and exhibit a relatively large amount of arcing. Charge chrome on the other hand exhibits considerably less arcing, and the extent of this arcing is highly correlated with the tapping of the furnace. The arcing measurements can also be used online in the control of the furnace, both for the electrodes and electrical circuit, and for the raw materials.

Jan 1, 2007

By M. Shahabi, M. Kashfi

This paper briefly describes the excavation procedure of a powerhouse, comprising of its incremental excavation, reinforcement measures, and the installed monitoring system. During the first phase of excavation, the data obtained from monitoring of the behavior of Mudstone layers were used to recommend extra support measures. These data are also used to design the support of the powerhouse during its extension phase. In diesen bericht wird die bohrmcthode von kraftwerk ecavation in stupenweise dargestelt, und in die richtung d.sicherung, Mit hilfe von monitoring systeme. Die monitoring in (mudstone) schichten ist an schutz in bohrung entworfen und montiert in diese methode in K.W. fase 1 schutzung das K.W. in erweiterung der K.W. das berte auserwelt worden ist Cet article décrit brièvement le procédé d'excavation d'une centrale électrique, comportant de son excavation incrémental, de mesures de renfort, et du système de surveillance installé. Pendant la première phase de l'excavation, les données obtenues à partir de la surveillance du comportement des couches de schiste ont été utilisées pour recommander des mesures supplémentaires de soutien. Ces données sont également utilisées pour la conception de la soutènement de la centrale électrique pendant sa phase d’extension.

Jan 1, 2003

By E. De Souza

Two comprehensive surveys, which focus upon backfill practices and the economics of backfilling in underground mines in Canada, have been conducted. The two surveys were designed to assess operational practices and costs associated with the wide scope of filling operations that must be met by individual mines, ranging from raw material feed to the preparation plant, through underground backfill transportation, to in-stope product placement. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database of information upon which they might compare their own practices and costs with present trends throughout the industry.

May 1, 2003

By Syd S. Peng

University research in the U.S. consists of three components; faculty, funding, and graduate students or postdoctorals. Individual faculty is the unit area of research that is not limited, although faculty normally performs research in their areas of expertise. Faculty can and often do join with other faculty in multidisciplinary research. Faculty research achievements or reputation reflects the standing of the program and university. Therefore, research is highly encouraged and regarded within the university community. Graduate students are the work force of faculty research and doctoral students are preferred for high-quality products. The federal government provides the majority of funding sources, with the remainder coming from industry, state government and others. Compared with other engineering majors, the mining engineering programs in the U.S. are unique in that they: ? Are small in terms of the number of programs, and number of faculty and students in each program. ? Serve a single industry (i.e., mining) and are thus cyclic, reflecting the up and down economic state of the mineral industries. Enrollment statistics during the past 70 years show that a cycle consists of approximately 30 years with the first 10 years up, followed by 20 years down. ? Have curriculum designed to emphasize and thus serve for either the coal, hardrock or industrial minerals industries. These unique features make mining engineering programs hard to manage in university environments. Funding for mining research has relied primarily on the federal government, i.e., the former U.S. Bureau of Mines (USBM) and currently the National Institute for Occupational Safety and Health (NIOSH). The mining industry does not directly perform, nor sponsor research projects. Federal funding provides primarily in-house research. In the last four decades, federal extramural funding was only available when Congress appropriated extra funding in response to mine disasters. For instance, a string of coal mine explosions in the mid to late 1960s prompted Congress to enact the Coal Mine Health and Safety Act of 1969. It provided massive research funding from 1970 to 1983 covering all mining-related subject areas. From 1984 to 1995, federal extramural research funding was minimal, through two generic mineral technology research centers for selected mining engineering programs. In 1995, Congress closed the USBM and transferred the health and safety of miners program to NIOSH. Federally-funded extra-mural research practically stopped from 1995 to 2006. In 2006 and 2007, in response to a series of disasters, including those at Sago, Aracoma, Darby and Crandall Canyon, Congress again appropriated funding for short-term re-search in selected subjected areas such as underground tracking and communication, mine seal and ventilation, and deep cover pillar extraction. Therefore, to develop a meaningful academic mining research program during the past three decades, funding needed to be drawn from other sources such as the mining industries. A ?meaningful? program requires a sufficient amount of consistent funding in order to produce effective results. A review of federally funded extramural research pro-grams shows that a great majority of contractors/grantees are private entities, involving few mining engineering faculty. This, in part, is due to the fact that mining engineering involves so many different subjects. Therefore, a small mining engineering program can only have resources to cover teaching in the core subject areas (i.e., extraction, ground control, ventilation and material handling), at best. In this respect, a successful and meaningful academic mining re-search effort requires strong supporting programs such as geology/geophysics, structural (applied) mechanics, material sciences, compute/software application, etc. Therefore, academic mining research had to rely on private sources such as coal companies, in the author?s case, for sustained funding in the past three decades. Relying on funding from coal companies presents several problems. The projects were small and considered routine consulting projects requiring practical answers in a very short time frame. This is not really suitable for academic research, for which the major goal of research is the training of graduate students. These short-term projects vary with time and mines, most of which are driven by U.S. Mine Safety and Health Administration (MSHA) or U.S. Office of Surface Mining (OSM) regulations. So sustained funding under such condition requires broad experience of coal mining operations, which is also not well-aligned for academic research where faculty tends to specialize in a narrow field. Consequently, under such a funding environment, it is important to keep in mind how to develop long-term academic research objectives from conducting small short-term consulting projects that require quick solutions. In other words, how to look beyond the quick answers and to develop broader and more fundamental theories applicable to other situations that advance the-state-of-the-art. In order to achieve this objective, faculty must act as the connecting link because graduate students come and go. Faculty must know the detail of each project such that they know what are the important unsolved problems, what to assign to specific graduate students and how to guide the next group of graduate students to continue the development and advance the mining science. Under such funding environments, the most effective way to conduct academic mining research and ensure quality products is to maintain a research group consisting of postdoctoral, PhD, and MS students of various rankings such that the senior ranks can assist in guiding the junior ranks, especially the senior PhD students who are experts in their dissertation research areas. A weekly meeting should be scheduled for the group in which problems encountered in the research are discussed or individuals take turns presenting the progress of their projects. During each meeting, the importance of open discussion on scientific issues must be emphasized. Thus, opinions are encouraged, debated, and rejected or accepted. Students are encouraged to listen to and analyze other points of view. In addition to training of this thought process, the meeting also helps identify the strengths and weakness of each individual. As the subject of research expands over time, the group?s and, thus, the faculty?s research experience broadens. With this approach, companies can get the quick answer they desire from expert research experience and the faculty can engage in meaningful applied and basic research that is most relevant to routine mine operations. The end result is that companies will have a high regard for academic mining research.

Jan 1, 2009

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.