Search Documents

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

By D. Washington

The US economy and the demand for nonfuel minerals grew at lower rates in 1995 than in 1994. Demand for major metals, such as aluminum, copper and steel, was mixed but relatively stable. The building industry, including highway construction, helped to support modest overall growth in demand for industrial minerals. The value of processed materials of nonfuel mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10%compared with 1994 (Fig. 1). The estimated value of US raw nonfuel minerals production during 1995 was $38billion, about 7% more than in 1994. The value of US minerals production has increased in 30 of the last 35years.

Jan 1, 1996

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

By S. D. D. Welsby

"A pilot-scale flotation column was used to evaluate four polyglycol frothers at Teck’s Highland Valley Copper Mine. The column was fed with flotation plant feed from the grinding circuit cyclone overflow. Frother dosage was changed by controlled addition to the column feed. Pulp, froth and metallurgical performance were assessed using gas dispersion measurements, water recovery and copper, molybdenum and gangue grades and recoveries. Ranking the frothers based on pulp and froth phase performance using gas dispersion measurements and water recovery yielded contradictory rankings. All of the frothers changed the froth structure in a similar manner such that, at the same structural conditions, they all gave the same degree of separation between water and entrained solids. The only difference between the frothers was what dosage was required to achieve a certain structure. Changes in pulp structure appeared to be related to the critical coalescence concentration (CCC) for each frother. Changes in froth structure were not completely described by the CCC and involved other factors, such as the hydrophobicity of particles in the froth. All of the frothers were capable of achieving the same metallurgical result, just at different dosages. Optimal dosages for the frothers were anywhere from the CCC, where copper and molybdenum grades were maximised, to 2 to 3 or 4 to 7 times the CCC, where copper and molybdenum recoveries, respectively, were maximised.INTRODUCTION Background Due to supply issues, Teck’s Highland Valley Copper (HVC) Mine replaced Dowfroth 250C, their auxiliary frother, with Huntsman Polyfroth W31. The primary criterion for selection was that the new frother gave the same performance as Dowfroth 250C, minimising disruption to the circuit. Frothers play a dual role in flotation, altering the bubble size in the pulp zone and the stability of the froth. A stronger or weaker frother, or a blend of both, will alter the balance between pulp and froth effects and, ultimately, metallurgy. Dowfroth 250C and Polyfroth W31 may not necessarily be the best frothers for HVC from a metallurgical standpoint. There may be a different frother or frother blend that could deliver higher recovery in the bulk roughers."

Jan 1, 2014

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By S. Rolseth, J. Thonstad

The traditional electrolyte for aluminium electrolysis is based on molten cryolite (Na3AlF6), acting as solvent for the raw material, alumina (Al2O3). Over the years there has been a trend to increase the content of excess aluminium fluoride (AlF3) to the cryolite-based electrolyte, in order to enhance the current efficiency of the process. In most cases one has ended up at 11?13 wt% excess AlF3because higher contents makes it difficult to control the heat balance of the process. This problem may be overcome if sensors are developed that will allow online control of electrolyte temperature and composition, and we may then see a surge towards still higher AlF3contents. In the development of new anode materials to replace the carbon anode with inert, oxygen-evolving anodes, focus is on anode corrosion, and a low electrolyte temperature is then highly desirable. While the conventional process operates at around 960°C, electrolyte temperatures as low as 750°C are being tested. This is achieved by having large excess contents of AlF3(40 wt%). The consequences of using such electrolyte compositions are discussed.

Jan 1, 2004

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012