Search Documents

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By A. Bobet

Design of a new underground laboratory is underway through the auspices of the United States National Science Foundation. The Deep Underground Science and Engineering Laboratory (DUSEL) is scoped to provide a diverse group of researchers with a dedicated underground facility capable of supporting a broad spectrum of fundamental and applied research at depth in the Earth?s crust. Key research partners in the endeavor are physicists, biologists, geoscientists and engineers. Engineers are not only designing the underground facilities, but are also actively involved in developing research initiatives. This paper will introduce the DUSEL engineering research program to the mining community, provide an overview of the site, geology, and laboratory facilities, and describe some key program initiatives. The particular technical challenges and opportunities afforded by the construction of DUSEL and the performance of the integrated science-engineering program will be discussed by reference to a subset of research initiatives that are currently under development: Cavern Design, CO2 Sequestration and Transparent Earth. These research initiatives target the development of new techniques that can support improved subsurface investigation, design and construction procedures. An increased use of the subsurface can actively contribute to the development of new, more sustainable solutions for use in mining and civil engineering practice.

Jan 1, 2011

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By J. A. Holmes, EDWARD C. FRANKLIN, RALPH A. GOULD

The commission may be permitted to express its earnest hope that the litigation which comes to an end with the findings and recom- mendations herein set forth will be considered by both parties to the action as definitely and equitably decided. The commission trusts that its work will show the value of the commission form of settlement and that its work will serve as a prece- dent to be followed in disputes relative to technical subjects. If the work of the commission is productive of a tendency on the part of technical litigants to avoid the use of the courts for the settlement of disputes it will not have been done in vain. Such tendency will surely grow and ultimately such differences will be arbitrated by technically trained men without recourse to the courts of law. Appended to the report of the findings of the commission are to be found the detailed reports covering the several lines of inquiry and investigation carried on by the commission and upon which its findings are based, and also a detailed statement of the fiscal affairs of the commission. A word of explanation is necessary in regard to the fiscal statement. While each party to the litigation has agreed to bear one-half of the expense of the investigations of the commission, it will be noted that the Selby Smelting & Lead Co. is credited with $21,000, while Solano County is credited with but $6,000. In order that the investigations of the commission might go forward without interruption the Selby Smelting & Lead Co. has generously supplied funds at the times they were needed. This assistance has been

Jan 1, 1915

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

By J V. Lawless

Mineralisation processes in epithermal deposits in the North Island of New Zealand are best illustrated by considering the two most productive deposits: Waihi and the Thames Bonanza Zone (TBZ), which have different mineralogies and ore shoots geometries. These two deposits can be taken as typical of certain styles of epithermal deposits worldwide, and recognition of their differences can be used to develop mineralisation models of predictive value. Waihi, the major economic producer in the Coromandel Volcanic Zone (CVZ), has laterally near-continuous ore shoots over a vertical interval of 600 m which consist of quartz, chalcedony, pyrite, base metal sulphides and electrum. They are found in the foot wall of earlier quartz veins which contain quartz pseudomorphs after platy calcite and adularia. The Thames Bonanza Zone which was the second biggest producer in the CVZ has discrete near-vertical ore shoots over 300 m vertically, which consist of quartz, pyrite, base metal sulphides, electrum and in their upper parts barite, that are enclosed in veins of quartz.   The gold mineralisation in both deposits is considered to be a co-precipitate with pyrite, with that at Waihi produced by prolonged boiling in an upflow of a hydrothermal system. That at the TBZ was produced by mixing a deep water primed for gold deposition by prior limited boiling, with an oxidised condensate of the steam released by the boiling, in an outflow proximal to the system's upflow.

Jan 1, 1997

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By Paul Grady, Martin Froehling, Curtis Mohns, Eliab Roman

"Since the idea of processing rock to unlock the valuable minerals inside was put into practice, efforts to improve production began. Methods have been learned that allow for operation in environments and under circumstances where it would not have been possible until now. All existing operations have experienced at least some form of productivity improvement measures. The objective is simple: generate more product of better quality in less time and at lower unit cost. Since the year 2000, various modifications have been made at the Kemess Concentrator in efforts to improve productivity. The following is a discussion of these modifications and their contributions to the success of the operation.INTRODUCTIONThe Kemess South Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines with a modern mill controlled by a fully integrated Foxboro IA DCS system and employing 134 people. On February 11, 2000 Northgate Exploration Limited (now Northgate Minerals Corporation) acquired Kemess Mine from receivership. Since acquisition in 2000, Kemess has seen many accomplishments, including the reduction of costs by 40% site wide.The mill has a nameplate capacity of approximately 56,000 tonnes per day which is processed through a Metso (Svedala) 60” x 89” Primary Gyratory Crusher and then conveyed by a 60” conveyor to a stockpile with 48 hours of total storage capacity. The nominal minus 6” rock from the stockpile is fed to two parallel grinding circuits (A & B). Each section consists of a 10.4 m F x 4.7 m SAG mill with dual drive motors (4,480 kW apiece) discharging onto a 2.4 m x 7.3 m Metso (Svedala) single deck vibrating screen to remove the coarse material for recycle to the SAG mill by a Continental 45º high angle sandwich conveyor. Screen undersize is pumped along with ball mill discharge to a cyclopac consisting of twelve Krebs 66 cm F cyclones to classify flotation feed to a size of approximately 65% minus 200 mesh. Cyclone underflow feeds a Metso (Svedala) 6.8 m F x 11.0 m ball mill, also with dual drive motors (4,480 kW apiece). The primary grinding circuit has 35,840 kW available for grinding."

Jan 1, 2005

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner's engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010