Search Documents

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By R. John Caulfield

The primary water supply system for the City of San Francisco and adjacent peninsula areas consists of aging and deteriorated pipelines crossing under the San Francisco Bay (the Bay). This system is highly vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The Bay Tunnel Project will replace the existing system with a 8-km-long (5-mi-long) tunnel underneath the Bay. The tunnel will be constructed using earth pressure balance methods and will have a two-pass lining system of precast concrete bolted, gasketed segments for initial support, and a welded steel pipe final lining. The project challenges include tunneling through both soft ground and rock conditions without any intermediate shaft access over the entire alignment. Seismic performance criteria include maintaining service flows after a large earthquake.

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler's ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By Jones S. C

A specific arc can be cut in hard rock formations using a specially designed multistep piloI bit, variable sized drift joint and long heavy control rod as a stabilizer rather than the Vaughan Thompson "Lifting" arc cuttingequipment. The rate of deflection can be controlled after an initial determination of behaviour in any particular rock type.

Jan 1, 1966

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

By John E. Tilton

Real copper prices during the past several decades display two striking characteristics. First, they are highly volatile. Within a year or two, copper prices can rise or fall by 30% or more. Second, over the longer term, they are falling. Indeed, since 1970, the secular trend price for copper is down by more than 50%. Figure 1 highlights both of these characteristics. It shows the average annual US producer price for copper since 1970 measured in constant 2001 US dollars. While the London Metal Exchange (LME) copper price is not shown, it and the US producer price have for some time moved more or less together. So pronounced short-run fluctuations around a significant long-run decline describe copper prices, not only in the United States, but around the world.

Jan 1, 2002