Search Documents

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

At the inception of the gold-mining industry at Kalgoorlie the small supply of firewood required for steaming purposes was naturally all drawn from the limited local areas, which promised soon to become denuded. With the advent of the railway toKalgoorlie came the ever increasing machinery and steam power, and the accompanying demand for firewood so increased that the fuel contractors began their operations, by following the timber belts along the Yilgarn railway line, and graduallygetting further westward, until at present we find them as far as Woolgangie, 63 miles from Kalgoorlie, and with the regular railway rates, I0. per ton per mile, this maybe considered the limit of payable timber at current rates. Although in the early days the reserve of timber along the railway line must have appeared as incalculable and inexhaustible as that of coal did in Europe a couple of centurys ago, the day is now near us when even this source will fail to meet the demands made upon it, for, although a good two years' supply is available or the areas under the axe, yet it is time to look ahead and find from whence the future supplies are to be drawn. Along the railways we find the zone of felling operations limited for want ofcommunication, and only such portions of the forests as are within six or seven miles of the railway come under the axe at present while virgin forests to the rear remain practically unexploited. It is only in the course of the past sixteen months that the firewood industry has developed...

Jan 1, 1901

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation is to improve the accuracy and consistency of mining processes and less to do with cost savings through labour reduction. A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio Tinto's surface mines. This paper describes Rio Tinto's drill enhancement project that has developed a robust system for automating most of the functions on a Terex SKSS16 drill rig. Automated drilling is currently being used in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the drill automation system is given together with an overview of how automated drilling is performed remotely from the mine office. A review of some of the benefits of the enhanced drill system is given together with the future plans to extend the functionality of the automated drill and the expected benefits.

May 1, 2010

By Philip J. H. Ball

The new application and development of grout jacking processes has combined, over the last decade in particular, to provide a method by which the effects of new underground construction on superficial structures can be controlled to acceptable levels. This paper sets out the basic principles, processes and limitations of compensation grouting. It describes key elements of the philosophy and design and details the control systems required to perform satisfactorily. To illustrate the application, a case history is described for the construction of a shaft and tunnel within and beneath the prestigious structure of Harrods in London.

Jan 1, 2000

By Jr. Kermit Allen

A study was conducted for the AEC to determine the feasibility of constructing an unsupported 315 foot diameter spherical cavity at a depth of 2,700 feet in a salt dome. A cavity of this size and shape has never been attempted. It was determined that the three basic essentials for solution mining; adequate salt, fresh water, and a means of brine disposal were available at the Tatum Salt Dome in Lamar County, Mississippi. Assuming a large, unsupported mined opening of the size and at the depth required would remain stable, the most practical method of providing the cavity using solution mining techniques is by use of a movable blanket of air to control the water level to properly shape the cavity while removing the insolubles either with jetting or by conventional mining methods. It is estimated that, using the jetting method of insolubles removal, the cavity can be constructed in 24 months for approximately $7 million. Using conventional mining techniques to remove the insolubles and shape the final cavity, it is estimated that the cavity can be constructed in 36 months for approximately $12.6 million.

Jan 1, 1968

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By Wilhelm Knickmeyer, Johannes Henneke

PREFACE For about 1 year Bergbau-Forschung GmbH, central research institute of the German Coal Mining Industry, undertakes full size tests for waterjet assisted tunnel¬boring in German coal mines (Fig. 1). These tests are performed with a tunnelborer of 2.6 m diam in an upper [ ]

Jan 1, 1979

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27'6" diameter, 78'O" deep Brandywine Street - 30'6" diameter, 88.6' deep Ellicott Street - 33'0" diameter, 110'0" deep

Jan 1, 1985

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004