Search Documents

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By David Baughman, Steven Axen, Ray V. Huff, Donald H. Davidson

Introduction In situ leaching (ISL) is an alternative method of mining uranium from deposits that are low-grade, deeplying, and water-saturated. ISL recovers uranium by transporting fluids through rock rather than by moving rock, a concept the Chinese developed over 2000 years ago for water production. This technique eventually evolved into production systems for oil, gas, sulfur, and salt. More recently, in situ methods have been developed to produce shale oil, gasified coal, geothermal energy, uranium, and copper. ISL uranium operations began in the early 1960s with Sabine Production Co. in south Texas. About the same time, Utah Construction and Mining Co. (Anderson and Richie, 1968) started similar operations in Wyoming's Shirley Basin. During the 1970s, six commercial operations were started in south Texas, (USBM, 1978) and a number of pilot operations were in various stages of development in Colorado, Wyoming, and New Mexico. This paper reviews some of the technical and economic aspects of the ISL process and briefly discusses key subsurface engineering functions as¬sociated with well pattern design and operation. While flow characteristics of a deposit are of prime importance, the following information is also needed: Depth, ore grade, total contained metal, ore thickness, flow conductivity (permeability), void space in rock (porosity), mineral type and distribution, natural groundwater flow, and structural features. Solvent selection, which is important to the economic success of the operation, takes these factors into account: Composition, rate of metal solubilization, interaction with gangue minerals, impact on rock permeability, impact on materials of construction, trace metal solubilization, cost, availability, and handling problems. Overview of ISL An ISL operation consists of these functions (Fig. 1): 1. Chemicals to dissolve and maintain uranium in solution are prepared at the surface extraction facility. 2. A set of injection wells forces the solvent into rock pores of fractures using pressure in excess of the deposit's hydrostatic pressure. 3. Solvent travels through the rock and reacts with uranium minerals to dissolve them. The solvent usually consists of an oxidant and a complexing agent in an acidic or alkaline medium. 4. A set of production wells creates a low-pressure sump where metal-enriched solution is collected for transport to the surface. 5. The enriched solution is processed to recover uranium and to separate the leaching solution for recycling through the system. The economic performance of an in situ operation may be estimated by integrating these related factors: (1) the flow rate of solution processed through the system, (2) rates of fluid injection and production from wells, (3) the rate of mineral solubilization in the liquid phase, and (4) the volume of rock swept by the fluid. As these factors reveal, ISL involves the technical disciplines of petroleum engineering, ore deposit geology, and hydrometallurgical processing. Wellfield Design Just as mineral engineers use drillhole information to plan a conventional mine, in situ engineers use similar information to design a well field. A thorough knowledge of deposit geology and reservoir properties is required. Early application of pressure transient testing, such as

Jan 2, 1980

Of the world's total production of gold the largest proportion comes from the more regularly consistent ore bodies, but in the aggregate an important part comes from those which are often irregular, uncertain and small. These smaller ore bodies are often high in grade and, as the capital required to work them is not large, they appeal to people seeking a quick and profitable return for a small outlay.These small mining concerns cannot afford detailed geological and petrological investigations and mapping, so they are very often dependent on local knowledge and experience which admittedly may be of really great value.Nevertheless the absence of skilled guidance may not only cause good opportunities for intelligent exploration to be lost, but discourage the seach for other ore bodies.lVIining engineers in the course of their travels in the examination of mines often come across such cases and also others where problems of finding lost ore bodies have been solved by the man on the spot. As records of cases are valuable and useful additions to the knowledge of ore occurrences, the writer now proposes to describe one such case coming under his observation in recent years.It is that of a small mine, known as the Idaho, at the southern end of the famous "Golden Mile" at Kalgoorlie (see Fig. 1). This mine has been a small and very erratic producer ever since it was abandoned by an English company which owned it forty years ago. Except for one period of four years it has always been owned and worked by parties of co-operative miners and during its time has gone through a tortuous career. Although it has often...

Jan 1, 1938

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

By Gartrell H. W

During investigations of the treatment methods for ore from the Bird-in-Hand gold mine carried out at Kalgoorlie and at these laboratories, it was found that excess alkali caused a lowering of extraction by cyanide, the cause of this being attrIbuted to the presence of a small amount of oxidised lead compounds in the ore. The subject has been discussed by various writers,3 but no satisfactory explanation of existing facts has been put forward. The experiments described in this report have been carried out with the object of obtaining some insight into the chemical reactions underlying the effect of lead salts and alkalis in cyanidation.The formation of cyanide-insoluble coatings on gold during roasting with lead compounds is well known, but the adverse effect of alkalis in cyanidation of ore is *This paper represents work done under a co-operative agreement between the Commonwealth Council for Scientific and Industrial Research and the South Australian School of Mines and Industries.Published by permission of the Mining Advisory Committee, Commonwealth Council for Scientific and Industrial Research.

Jan 1, 1935

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003

By E. Snyders

The upgrading process of an inferior grade of zircon to a superior opacifier for ceramic applications was investigated. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated in this study. The morphology of the treated and untreated zircon opacifier samples were investigated by SEM micrographs and the colours of zircon samples were characterized on the grounds of the Commission Internationale de l`Eclairage (CIE) standard procedure (CIE L* a* b* measurements) after application on a bisque ceramic tile. It was found that the treatment improved both the milling as well as the opacifying properties of the treated inferior grade zircon concentrate and renders it equivalent to or better than prime grade zircon opacacifiers currently produced. Keywords: ZrSiO4; opacifier; colour; milling; calcining.

Jan 1, 2005

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014