Search Documents

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By Alvaro Ordoñez

El presente texto describe el nuevo método para la obtención de cobre por lixiviación de minerales mixtos de cobre en medio básico, donde la disolución de minerales mixtos de cobre se realiza a través de un medio lixiviante compuesto de hipoclorito (lejía) y amoniaco en un medio básico. En ese sentido, se busca extraer cobre, a presión y temperatura normales por lixiviación con cloro acuoso - amoniaco, a partir de minerales oxidados y mixtos, así como recuperar el cobre contenido en el PLS mediante electrodeposición directa, obviando la etapa intermedia de extracción por solventes, para obtener como producto final cobre catódico.

Sep 12, 2011

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

In order to deliver a quality shotcrete and concrete product underground for the extensions to the Cullinan Diamond Mine operations it was decided to develop a new, simpler concrete product to meet underground support requirements. The aim was to develop a concrete product that not only reduced costs but also met the performance criteria of the current range of concrete products used on Cullinan Diamond Mine, a 25, 45 and 60 MPa concrete and a fibre reinforced wet shotcrete. The concrete product batching and delivery system was to be from surface as opposed to the current underground batching systems. The operational principle was to include an automated surface batching plant with delivery of the concrete product to a borehole containing suspended pipelines delivering to an underground storage facility from where the product is delivered to the working area by further pumping or agicars. Keywords: concrete, shotcrete, full flow, frictional loss, pipeline transport, positive displacment pump

Jan 1, 2006

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Fred Breu, Ronald E. Heuer

INTRODUCTION The Point Lepreau nuclear generating station was constructed in the late 1970's and early 1980's by the New Brunswick Electric Power Commission. Point Lepreau is a small peninsula on the north shore of the Bay of Fundy, about 55 km west of St. John, New Brunswick. Cooling water for the plant was to be obtained from and discharged into the Bay of Fundy by the system of shafts and tunnels illustrated in Fig. 1. The design engineer for the cooling water system was Albery, Pullerits, Dickson and Associates, Ltd., Toronto. Ferrera-Resco Ltd, Windsor, Ontario, was contractor for construction of the cooling water shaft and tunnel system, which was done between 1976 and 1979. The senior author was project manager for Ferrera-Resco, the junior author served as consultant to Ferrera-Resco on evaluation of certain geotechnical questions which arose during construction. SITE CONDITIONS Geology Except for limited overburden soils at the onshore shaft sites, the tunnels and shafts were constructed entirely in Triassic conglomerate, sandstone, and siltstone, with some shale interbeds. The bedding strike averaged about N6°E, The dip was to the west at about 30° along the Discharge Tunnel and 40° along the Intake Tunnel. Rock along the Intake Tunnel was mostly sandstone and siltstone and more thinly bedded, with RQ D generally in the range of 50 to 60%. Rock along the Discharge Tunnel tended to be coarser sandstone and conglomerate and more thickly bedded, with higher RQ D averaging about 80%. In addition to bedding joints, two other joint systems were identified

Jan 1, 1985

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By Robert S. Shank

Introduction The Pinto Valley open-pit copper mine is located in southern Arizona, 11 km (7 miles) west of Miami. Production at Pinto Valley began in 1974. About 350 Mt (386 million st) of ore and waste was removed by the end of June 1982. At that time, the mine was using more than 90 major equipment items with a total mobile fleet numbering 320. Some of the major equipment consisted of four Marion M4 rotary drills; six P&H 15, 11.5- and 19.1-m3 (15- and 25-cu yd) shovels; and 24,136- and 154-t (150¬and 170-st) Wabco haulage trucks. This equipment was used to move more than 139 kt/d (154,000 stpd) of ore and waste. The mill was processing more than 50 kt/d (55,000 stpd) of mine ore. Shutdown A two-week vacation shutdown began in July 1982. Maintenance jobs were scheduled, and most employees left for the vacation. During the vacation period, copper prices fell below $1.32/kg ($0.60 per lb). Inventories remained at alarmingly high levels. At this point the mine was losing more money operating than it would by being shut down. The vacation shutdown was first extended to five weeks. But, after further evaluation, the mine was shut down indefinitely. In Dec. 1982, Cities Services Co., owner of Miami Operations (which included the Pinto Valley mine and mill), was acquired by the Occidental Petroleum Corp. On March 1, 1983, Occidental sold the operations to Newmont Mining Corp., and Newmont created Pinto Valley Copper Corp., as a wholly owned subsidiary. Copper continued to be produced by the Pinto Valley solvent extraction-electrowinning (SX- EW) plant because of its low cost per pound of production. To ensure proper equipment care during the shutdown, maintenance management was given three goals; • maintain the SX-EW plant; • maintain the environmental and pollution control systems such as domestic water pumps and mine dewatering; and

Jan 4, 1985

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990