Search Documents

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By Zhang Chuanfu

Keywords: solid solution, Ni-Co alloy powders, thermal decomposition, fibres. Synthesis of fibrous Ni-Co alloy powders was achieved by thermal decomposition of precursor of complex Ni-Co oxalates solid solutions obtained via modified coprecipitation method among intimate mixing solution of NiCl2?6H2O , CoCl2?6H2O and H2C2O4?2H2O in the presence of surfactant polyvinylpyrrolidone (PVP) and organic solvent ethanol. Scan electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), disperse energy X-ray analyses (EDX) were used to characterize the structure features and chemical compositions of the as-prepared fibres. The influences of decomposition conditions, including temperature, time, the flow rate of N2+H2, and the heating rate, on the morphology, average size and specific surface area of the Ni-Co alloy powders were investigated. It is found that a trend of the mutual alloying of nickel and cobalt: the formation of perfect solid solution for any compositions NixCo100-x was indicated and corresponding NixCo100-x alloys with fcc phase can be obtained under the optimal conditions.

Jan 1, 2005

Advances in Optical Image Analysis and Textural Classification of Iron Ore Fines

Sep 13, 2010

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

By C. A. Johnson, K. F. Unrug

The identification of the major subsidence areas in the Eastern Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location. Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential.

Jan 1, 1986

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

By J. Kulas, J. Weaver, K. Hagley

An assessment of potential groundwater movement beneath the tailing impoundment at the Red Dog Mine was performed, and has indicated a unique aquifer situation within sub-permafrost groundwater at the site. The aquifer was shown to be isolated from both vertical recharge and a real discharge, and is characterized as a virtually no-flow system. The permafrost resulted in a deep aquifer with high tidal efficiency, meaning that variable surface loads are easily transmitted to the fluid. The tidal efficiency has been characterized through analysis of water level fluctuations that respond to earth tides, barometric pressure loads, and loading from the pond.

Jan 1, 2002

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By H. E. Bartlett

In the operation of some flotation plants treating platinum ores it was found that there were imbalances between the inputs and outputs. The inputs and outputs were sampled as slurries and it was determined that the imbalances arose from biases in the sampling, despite the samplers having been designed according to well-established rules. The launders feeding the sample cutters, and the sample cutters themselves were redesigned using finite element analysis to model the flows. A new set of design rules were formulated. The application of a Components of Variance Analysis, to determine the variance of primary and secondary sampling and of analysis in the lab for a concentrate is presented to illustrate the need for frequent sampling of process streams.

Jan 1, 2002

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

Study of Bauxite Separation by Using Flotation Column

Sep 13, 2010