Search Documents

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By Jing Zhong, Yugang Li, Chen Yan, Shaoda Zhang, Qian Wang

Online surface quenching technology has been developed for the hot charging process to prevent the surface cracks in high strength low-alloy steel slabs. In this paper, a two-dimensional heat transfer model of surface quenching process was presented. This finite element model includes nonlinear thermodynamic properties, by which the slab temperature distributions were computed. The model predicted temperatures show reasonable agreement with the measurements. The effects of the water flow rate and slab movement velocity on temperature variation during the quenching and subsequent tempering process were investigated. The result shows that the temperature drop increases but the tempering temperature changes slightly with increasing water flow rate and decreasing slab velocity. Keeping the slab movement velocity at 1.2-2.1m/min and the water flow rate at 55-70m3/h, the slab surface experiences a temperature drop of 400-600 firstly, then recovers above 650, the quenching and energy-saving effect are remarkable.

Jan 1, 2015

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

By N. G. Azeredo

This work dealt with the evaluation of engineering structural clay brick samples that were sintered at estimated temperatures of 700 and 800°C. They were collected in a red-brick plant in Campos dos Goytacazes, RJ, Brazil. From a lot, a sample already sintered in its kiln at 700°C were collected and also a sample from the same lot only dried by the air, which were then sintered at 800°C controlled temperature. The samples were subjected to Brazilian Standard tests (ABNT NBR 15270:2005) to determine their geometric, physical and mechanical properties. In order to be classified as structural clay brick it is required minimum 3.0 MPa for the characteristic compressive strength (fbk) to be suitable for up to five floors structural building applications. We also used the Weibull Probability Plot and Weibull Maximum Likelihood Estimation to evaluate distribution parameters in order to compare the results of compressive strength obtained in the tests.

Jan 1, 2015

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By Mingmei Zhu, Xin Qiu, Xiaofei Dou, Yu Wang, Tiancheng Lin, Bing Xie

In this study, the slag forming route of the single-slag steel melting when smelting medium phosphorus hot metal was investigated. The CaO-SiO2-FeO-MgO-MnO-P2O5 as hexahydric slag system was adopted in the converter. The effect of slag composition on liquidus was calculated by FactSage, the isogram of phosphorus distribution ratio was calculated by using the regular ion solution model, combining these two tasks, the theoretical slag forming route was obtained. Through experiments, the actual melting point ofthe corresponding components on theoretical slag forming route was obtained, in this way, the theoretical slag forming route was confirmed. Then, the theoretical slag forming route was applied to industrial test in a 210t BOF. After using the new slag formating route, the dephosphorization ratio was increased 3.6% while the auxiliary materials consumption was reduced, and the cost of steelmaking was reduced.

Jan 1, 2015

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By Harold R. Kokal

Lisakovsky is a 3-billion ton oolitic iron ore deposit in north-central Kazakhstan operated by Orken LLP, a subsidiary of Ispat Karmet and the LNM Group. The iron oxide minerals are goethite and limonite. The gangue occurs as discrete quartz grains and an unidentified form of colloidal silica-alumina. The concentrate produced contains about 49.5 percent iron (Fe) and 0.6-0.8 percent phosphorus (P) or 10-20 times the acceptable phosphorus level. The phosphorus is intimately associated with the iron oxide and colloidal gangue, no discrete phosphorus minerals are found, and beneficiation is not possible. Therefore, to reduce the phosphorus, a hydrometallurgical process that includes roasting followed by leaching in dilute sulfuric acid has been developed. Phosphorus extraction is 70-90 percent, with only a minor loss of iron. The process has been tested in the laboratory and in a pilot plant at 50-300 kg/h. Construction of a 900,000 t/y demonstration plant is underway.

Jan 1, 2003

By Oleg B. Girin, Yuliya O. Proshenko

"Several approaches to electrolytic synthesis of new types of composite coatings with improved properties were devised using the authors' findings on development of texture, substructure and structural state in metal electrocrystallization. Addressed are texturally composite coatings having improved resistance to wear and corrosion; substructurally composite coatings having improved hardness and corrosion resistance; phase-change constitutionally composite coatings having improved corrosion resistance, reflectance, hardness and resistance to wear; structure-change constitutionally composite coatings having improved electric and magnetic properties; restricted-substructure composite coatings having improved resistance to abrasive-impact wear; and modified-substructure composite coatings having improved strength and plasticity.IntroductionIn recent years, some trends in the formation behavior of crystal texture, crystal substructure and structural state of electroplates were revealed and effects of texture, substructure and structural type on electroplate properties were discovered (1-3). Our interest was in using these findings and effects to develop some ways of synthesizing new types of composite electrolyte coatings having enhanced properties."

Jan 1, 1998

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

By J. A. Voigt

In an effort to determine the optimum conditions for preparing high purity, fine particle size high temperature superconducting oxide powder, we have investigated how calcination conditions influence the conversion of a chemically prepared hydroxycarbonate precursor powder to YBa2Cu307. We find that the precursor can be converted to phase pure YBa2Cu307 in either oxygen or synthetic air (20% 02. 80% N2) at 850°C. This temperature is substantially lower than the temperature (>900°C) normally used for the calcination of mixed-oxide powders. The lower calcination temperature prevents particle sintering and maintains the desired fine particle size. Powder processed in synthetic air shows a low degree of crystallinity indicating it may be more sinterable than the highly crystalline powders produced when an oxygen atmosphere is used. Intimate contact between powder particle surfaces and a flowing gas atmosphere promotes the reaction between the BaCO3 component of the precursor powder and the Y and Cu constituents.

Jan 1, 1989

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By Anita E. Lam

The thiosulfate leaching of gold generally requires the presence of a catalyst such as cupric tetraammine, Cu(NH3)42+, to obtain reasonable leaching rates and gold extractions. Unfortunately, this same catalyst that accelerates gold leaching also tends to accelerate thiosulfate oxidation to tetrathionate and other species. It is therefore imperative that a detailed understanding of the role of this catalyst and the factors affecting it is obtained. It is equally important for plant application that a method of assessing the catalyst be developed. In this work the role of the cupric tetraammine catalyst was studied using geochemical modeling for speciation prediction, thiosulfate leaching of gold ores, and chemical analyses of resulting leach solutions. It was found that the variables of pH, temperature, and the concentrations of ammonia, thiosulfate, and total copper all work in concert to affect the concentration of the cupric tetraammine species. It was also found that the presence of sufficient thiosulfate and cupric tetraammine was critical to the success of the leach.

Jan 1, 2003

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By Hirokazu Narita

The extractability for Pd(II) using MOTDA and DHS and their durability against a mixed solution of HNO3 and HCl was investigated by solvent extraction and FT-IR measurements. Both MOTDA and DHS selectively extracted Pd(II) over Pt(IV) from 0.75 M HNO32.25 M HCl solutions. The extraction rate of Pd(II) with MOTDA was much greater than that with DHS. In the durability test, the extraction percentage of Pd(II) and the FT-IR spectra were measured using MOTDA and DHS after stirring with 0.75 M HNO32.25 M HCl solutions. The extraction percentage of Pd(II) with MOTDA hardly changed during the two-month stirring; however, that with DHS decreased with an increase in the stirring time. The FT-IR spectra showed the sulfoxide formation by the oxidation of the sulfide in DHS, but not in MOTDA. Consequently, it was found that MOTDA is more durable than DHS.

Jan 1, 2006

By William Ewing

Copper is rapidly being adopted by the semiconductor industry as the interconnect material of choice. The aqueous processing techniques used generate wastes such as spent electrolyte from electroplating, electroplating rinse water, copper solutions from removing copper from the back of the wafer and CMP waste streams. We are examining the use of chelating resins as a means of recovering copper from these streams within the processing plant, thereby allowing recycling of process water and minimizing hazardous waste disposal costs. We have examined the effect of model plating additives (and other organic complexing agents) on the efficacy of Dowex M4195. Although these might have had a significant effect, commonly used electroplating additives polyethylene glycol (PEG), benzotriazole (BTA), thiourea, glycine, and 3-mercapto-1-propanesulfonate (MPSA) each had little or no effect on the ability of the resin to chelate copper and remove it from solution. This suggests that Dowex M4195 could be useful for treating waste solutions of rather variable compositions.

Jan 1, 2003