Search Documents

By T. Takasu

Overall productivity in copper refining is currently determined by the electrorefining process. Previous research showed that forced convection of the electrolyte improves the morphology of the copper deposit on the cathode and suppresses passivation of the anode. In this paper, electrorefining experiments under forced convection were carried out in the presence of As, Sb and Bi impurities, both in electrolyte and in the anode, to determine the effect of the impurities on the electrorefining process. The concentrations of the impurities in the deposit increased with increasing current density without forced convection. An increase in the fluid velocity suppressed the increase in impurity concentration. These concentrations were high, especially in the initial stage of deposition without forced convection, corresponding to a decrease in the cathode potential measured during that period. This indicates that the enrichment of impurities was induced electrochemically. The reason for the decrease in cathode potential was the low concentration of copper ions on the electrode surface because of ion consumption by the electrolysis. The forced convection of the electrolyte enhanced the ionic mass transfer and thus suppressed the polarization and deposition of the impurities. The fluid motion was shown to be effective in achieving electrolysis under high current density conditions.

Jan 1, 1999

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By Mahesh C. Jha

Molybdenum, a major refractory metal, is widely used as an alloying element in steels and superalloys to improve their corrosion resistance, physical properties and mechanical strength, particularly at elevated temperatures. The current worldwide production and consumption is estimated at about 130,000 tons contained molybdenum per year. Molybdenum occurs in nature as molybdenite mineral and is recovered by a flotation process as a primary concentrate at molybdenum mines and as a byproduct concentrate at copper mines. The concentrate is roasted to a technical-grade molybdic oxide (tech oxide) in multiple-hearth roasters. About 80 percent of the tech oxide is sold, as such or after conversion to ferromolybdenum, for addition to iron and steel. The remainder is further refined to pure oxide and molybdate chemicals that are used in the manufacture of catalysts, specialty chemicals, molybdenum metal and superalloys. This paper discusses the various steps in the extractive metallurgy of molybdenum, from flotation of sulfide concentrate to reduction of pure oxide to molybdenum metal.

Nov 26, 1999

By Rauf Hurman Eric

In this review paper the effect of composition and temperature on electrical conductivity and viscosity of the slags encountered in electric smelting of PGM-containing sulfide concentrates is described along with their liquidus temperatures. Optimization of slag composition is attempted on the basis of opposite trends of viscosity and electrical conductivity. Metal losses to slag, matte-slag separation and matte settling are also discussed in conjunction with interfacial and surface tension concepts. The electrode immersed in the slag phase is the main factor in the design and operation of the furnace. The most important electrode parameters are the size and the positioning in the slag phase which are determined by the slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles within the slag phase which in turn affects the flow conditions. Thus the flow of slag is discussed together with furnace geometry, stirring action, buoyancy and electromagnetic effects and the action of the electric furnace as a settler is emphasized. A discussion on the design d production capacity of the furnace is provided which are based on considerations derived mainly from slag properties.

Jan 1, 2006

By T. W. Gonzales

The BHP San Manuel Smelter operates an Outokumpu Oy flash furnace, conventional Peirce-Smith converters, anode casting facilities, and two double contact sulfuric acid plants. The flash furnace was commissioned in July 1988 and since then, the smelting capacity has been continuously increased to 30% above design. The converter operation was challenged to process larger amounts of matte with existing capacity. Utilization of industrial technological improvements and people technology transformed the Converter Department from a constraint to easily accommodate the new demonstrated flash furnace capacity. This technology also increased secondary consumption, converter campaign life, and reduced operating costs. This paper will describe the important Converter Department achievements in the past five years.

Jan 1, 1999

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By Henry Salomon-De-Friedberg

Quebrada Blanca has had to overcome numerous challenges in achieving design throughput. The paper reviews how actual practice has evolved from the original design. The major challenges that were encountered from heap leaching to solvent extraction, the tankfarm and through to electro winning are discussed. The eventual solutions to some of the key issues are presented.

Jan 1, 1999

By Takahiko Okura

Japanese non-ferrous industry introduced large-scale smelting plants along seashores for overseas concentrates with increasing demand of metals around 1970s. Although serious environmental pollution became obvious, with economic growth, the industry got rid of pollution by installing new processes and improving operation technologies. At present, over 99.8% of sulfur input to smelters is fixed as stable compounds. Through those decades Japan had steep rises of oil prices, sudden change of exchange rate, and inadequate treating charges, we were faced to consider the closure of smelters. The industry has survived by increasing productivity, saving energy and reducing manpower. Furthermore the industry made great effort to recycle valued metals from scraps and wastes for the resources-recycling society. Academic research also contributes to support these individual technologies. Thus the industry has fostered world-acclaimed technologies in terms of efficiency and energy conservation. This paper presents technology development and environmentally-benign sulfide smelting processes.

By Andrzej Warczok

Liquid slags produced in smelting of copper concentrates contain copper in a dissolved form as well as mechanically entrained inclusions of copper matte. Coalescence and sedimentation of inclusions during slag cleaning plays a key role in copper recovery. Liquid matte inclusion in a molten slag presents a system of metallic conductor in an ionic solution. Constant electric field induces migration of the matte droplet along the current lines. Additional phenomena occur in a system under crossed electric and magnetic fields. Electromagnetic buoyancy force acting on the inclusion affects its settling rate. Electromagnetic buoyancy force of insulating and metal spheres has been measured in a liquid synthetic slag. It was found that depolarisation of the metal sphere, related to the electrode reactions occurring in the surface, plays an important role in the determination of the direction and magnitude of the electromagnetic force. On the basis of the existing theories and results of measurements a mathematical model describing the behaviour of metallic inclusions in the liquid slag under the influence of crossed electric and magnetic fields was developed. Simulation of behaviour of copper matte inclusions under crossed fields showed trajectory of motion in a liquid slag as a function of the slag properties and the inclusion size.

Jan 1, 2003

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By Gary A. Campbell

This article is an analysis of world consumption of copper for the years 1976-1996. It is done to provide a comparison of what has happened over this time period with the trends of previous years in order to learn more about world copper consumption and to forecast world copper consumption trends into the new millennium. The analysis begins by documenting the geographic trends of consumption of copper for the years 1976-1996 by both region and key individual countries. Then, variables based on the intensity-of-use hypothesis and the intensity-of-use technique are selected and tested against the observed consumption behavior by using the correlation coefficient technique. The statistical results and their implications for the consumption of copper into the new millennium are discussed.

Jan 1, 1999

By KNona Liddell

Many metal recovery processes Involve heterogeneous reactions In porous media accompanied by fluid flow and mass transfer. Modeling such systems Is difficult because of the number of rate processes Involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide, an attractive alternative to models based on transport ,mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.

Jan 1, 1996

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997

By Yun Li

In 1999 Yunnan Copper Corporation (YCC) decided to modernise their copper smelter and change the existing sinter plant I electric furnace process to a combination of ISASMEL T and electric slag cleaning furnace. The main aim of the project was to improve the environmental performance and decrease the energy consumption. Generally the project has been successful, partly attributable to the selection of a reliable and fully demonstrated technology. The design capacity for the ISASMEL T furnace is 600,000 tonnes of dry copper concentrate per year. The furnace has been running smoothly since heat up in May 2002. YCC expended considerable effort in the preparation for plant operation. An extensive training program for key YCC personnel at the Mount Isa Copper Smelter improved their understanding of the process significantly and ensured successful hand-over of the technology. This paper describes the project history and summarizes initial operating results.

Jan 1, 2003

By Michael P. Meisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halo¬gens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By K. Koike, N. Masuko, Y. Takasaki

At the Zinc & Lead'95 symposium, one of the authors presented several modifications of Pb-Ag-Ca alloy anodes for the zinc electrowinning process, and also, the behavior of some organic additives in the electrolyte. In this study, the mechanical properties of the electrode materials composed by Pb-0.5 wt% Ag-(0~0.8) wt% Ca were studied by the tensile and Vickers hardness methods. Furthermore, experimental research on the influence of rolling and annealing treatments on the electrolytic behavior and mechanical properties of these alloys was carried out. The tensile strengths of the annealed Pb-0.5 wt% Ag-(0.1-0.8) wt% Ca alloys were the same or higher than those of the as-cast Pb-0.9 wt% Ag alloy. The anode potential using the as-cast Pb-0.5 wt% Ag-0.6 wt% Ca alloy decreased compared to the as-cast Pb-0.9 wt% Ag alloy. Moreover, the annealed Pb-0.5 wt% Ag - 0.6 wt% Ca anode after rolling showed a lower anode potential than the as-cast Pb-0.5 wt% Ag - 0.6 wt% Ca anode.

Jan 1, 2000

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Thomas Gliick, Jianming Lu, David Dreisinger

"The recovery of manganese from the Boleo project of Baja Mining is via an acid oxidation and acid reduction process in seawater. Manganese as manganese dioxide is leached into solution as manganese sulphate with the addition of sulphur dioxide gas as a reductant and then precipitated as a manganese carbonate. The use of the manganese carbonate intermediate to produce electrolytic manganese metal (EMM) has been extensively studied. The manganese carbonate can be used in place of natural (MnC03) or reduced ores (MnO) of manganese as a feed to the EMM plant. Manganese carbonate can be dissolved in spent electrolyte from manganese plating, followed by purification using ammonium sulphide precipitation of minor elements and then electrowinning in a selenium free process. The results of small cell testing of manganese electrowinning are reported.IntroductionThe Boleo Project of Baja Mining is a greenfields development currently under construction approximately 5 km north of the town of Santa Rosalia, Baja California Sur, Mexico. The Boleo property is held by the Mexican company, Minera y Metalurgica del Boleo S.A. de C. V. (MMB). MMB is owned 70% by Baja Mining Corp. and 30% by a consortium of Korean companies consisting of KORES - Korea Resources Corporation, LS Nikko Copper, Hyundai Hysco, SK Networks and lljin Copper.The Boleo deposit has Measured and Indicated resources of264.7 million tonnes grading 1.50% copper equivalent (CuEq) & Inferred resources of 159.9 million tonnes grading 1.15% CuEq. The calculation of copper equivalent is based on a combination of metal prices and predicted metallurgical recoveries (Table I). The metallurgical recoveries have been confined by extensive bench and pilot plant testing. Proven and probable reserves are available at Boleo to provide for more than a 30 year mine life. Initially, 25 years of mine life and 23 years of process plant operation have been scheduled in the February 2010 Technical Report Update (www.sedar.com)"

Jan 1, 2012

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By Lars O. Werme

Already the KBS Project proposed copper as a suitable material for encapsulation of spent nuclear fuel. The basis for this choice was the thermodynamic stability of copper in water and the fact that deep granitic groundwaters in Sweden are oxygen free. With a limited supply of oxidants, a copper canister would have the potential for a very long service life. The research and development work aiming at encapsulating nuclear fuel entered a new phase in 1993, when SKB launched its Encapsulation Plant Project. Within this project, SKB has: ? designed a facility for encapsulation of nuclear fuel, ? laid down the design premises for a canister for disposal of nuclear fuel, ? tested and developed fabrication methods for copper canisters, ? evaluated the long term chemical and mechanical behavior of the canister, ? made preliminary plans for a factory for the production of copper canister, ? constructed a canister laboratory for full scale testing of the key operations in an encapsulation plant. The conclusions of this project were that a canister consisting of an outer layer (50 mm) of copper over an insert of cast nodular iron would provide sufficient corrosion protection and would have sufficient mechanical strength. This canister can be produced by several methods of which forming from rolled plates, hot extrusion, and "pierce and draw" have been tested at full scale. The canister will be sealed by electron beam welding in the encapsulation plant, and the integrity of the weld will be verified by ultrasonic testing and' high-energy radiography. The final development work in this area will be performed in the canister laboratory.

Jan 1, 1999