Search Documents

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By Thomas L. Vandergrift

The type and severity of coal mine entry failures are affected by the strength and stiffness properties of the roof, floor, end coal. Knowledge of the mine-wide trends of these properties Is valuable in developing effective ground control plans. Within the context of a larger effort to Improve entry stability In high horizontal stress fields, the U.S. Department of the Interior, Bureau of Mines, has evaluated three portable, on-site test devices to determine their suitability for identifying mine-wide physical property trends. The devices evaluated were the borehole shear tester, the Schmidt harmer, and the point load tester. Despite the lack of standardized data Interpretation procedures, each device provided useful on-site physical property data. The Schmidt homer was preferred for trend identification because of Its speed and simplicity. Schmidt hammer data were collected over a large area of an underground coal mine to compare calculated roof strength trends with a known geologic feature.

Jan 1, 1990

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

The objective of extensive underground experimentation on three longwall coal faces was to improve the stability of mechanised longwall faces through investigation of the relations between support resistance and convergence and resultant deformation of roof and face strata. In particular the influence of high setting and yield pressures on several strata and support parameters was studied in great depth. Increased setting pressures resulting in an increase in setting load densities from 0.15 MN/m2 to O.45 MN/m2 were shown to reduce convergence, face spalling roof flaking, lateral movement of roof and floor, extrusion of the face wall and progressive failure of the coal wall ahead of the face. This was shown to result mainly from the change in roof strata deformation from a wedge shaped compression zone with tension at the face edge to an even beam shaped compression zone over the face area. Debris thickness above the support canopy and below the base was observed to be the one of the most variable parameters which influenced the support characteristics particularly the rate of load acceptance by supports and the roof to floor convergence. A setting load density of 0.4 MN/m2 to 0.5 MN/m2 was found to be optimum under soft to moderately strong sandstone roofs. The authors demonstrated that use of guaranteed set valves with powered supports contribute to good strata control, reduce face down-time and increase face productivity.

Jan 1, 1984

By Keith Heasley, Christopher Newman, Zach Agioutantis

"Previously, in 2013, a laboratory version of the computer code ARMPS-LAM, introduced at the 32""d International Conference of Ground Control in Mining, successfully integrated the laminated overburden model of LaModel into an ARMPS-style pillar stability analysis. The ARMPS-LAM analysis has now been fully integrated into the ARMPS program allowing users to more accurately classify the stability of a given mine design utilizing a laminated overburden model for the determination of pillar loading within theAMZ. ,This paper introduces the new Windows-based ARMPS-LAM program. The program's ease of use, output result generation, and limitations are highlighted through the parametric analysis of three hypothetical case studies where traditional ARMPS output is compared to output generated by LaModel. As mining operations continue to produce at greater depths and in more complex geometric and geological conditions, flexible and efficient analyses of mine stability for underground room and pillar mining has become more and more essential. The ARMPS-LAM program provides the mining industry with an empirically backed, numerical design tool for the evaluation of underground room and pillar mine plans.INTRODUCTIONIn the Southern Appalachian coal fields of the United States, retreat room-and-pillar methods have allowed mining operations to maintain high rates of production in the face of adverse geologic conditions and shrinking coal reserves. Over the years, research has been dedicated to understanding and mitigating mining-related dangers due to second mining practices, such as: pillar squeezes, floor heave, roof falls, pillar bumps, etc. However, as mining operations continue at deeper depths and with more complex geometric and geologic conditions, there is an inherent industry need for more accurate, flexible, and faster evaluations of stability for underground room-and-pillar mining."

Jan 1, 2016

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Kot Unrug

For the purposes of underground mine design, twelve cores of the Springfield (V) Coal (Pennsylvanian) roof and floor were retrieved. Each core was photographed, described fresh in the barrel, and the rock quality designation (RQD) was measured. Cores were wrapped in plastic and delivered to the rock mechanics lab. At the lab RQD was remeasured and new photographs were taken before running geotechnical tests including weatherability. Significant differences in barrel RQD's vs. lab RQD's have been noticed in spite of careful handling. The drill site RQD is generally used to calculate geotechnical results, but in some types of coal measure rocks, further fragmentation of core takes place with slight changes of moisture content, which occur even in well wrapped core. This creates a dilemma which RQD should be used for support design. Rocks around excavations are exposed to the significant changes in moisture content due to the seasonal weather changes and related fluctuation of humidity of air ventilating a mine. Therefore, it appears to be more realistic using laboratory RQD which corresponds closer to the actual rock condition around the excavation. Weatherability test, developed for characterization of time dependent behavior of rock exposed to fluctuations in moisture content, is thought to be related to the above-mentioned changes of RQD. In weak shales, mudstones and claystones which weather rapidly, it is essential to characterize their future behavior in the pre-mining stage. This can allow for a realistic design of primary, and particularly secondary support in coal mines, especially in coal fields where such geologic conditions exist.

Jan 1, 2003

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Takashi Sasaoka, Hiroshi Takamoto, Kikuo Matsui, Hideki Shimada

"Indonesia is the second largest coal exporter to Japan. Almost all the coal is produced from open cut mines. However, a great deal of coal is left in the highwalls of the mined-out pits. The use of highwall mining systems has increasingly come into play in the U.S. and Australia, when overburden depth exceeds economical recovery in an open cut mine. However, the stability of the highwalls is always a major safety concern in such mining. This paper describes the characteristics of the highwall mining system and discusses the appropriate highwall mining system for use in Indonesia.INTRODUCTIONIndonesia produces over 200 Mt of clean coal and is the second largest coal exporter to Japan, accounting for about 32 Mt of coal annually. Over 99% of the coal produced in Indonesia comes from surface mines. More open cut mines will be developed and more coal will be mined in order to fill the great demand both in Indonesia and the rest of the world.In open cut mines in Indonesia, there are many sites where mining operations have developed long highwalls that have been abandoned due to the current economics. Mining operations have been transferred to lower stripping ratio blocks of coal or overlying seams. In some cases, coal lies buried beneath spoil heaps or is covered with mud and water. It is estimated that there is a great deal of coal beneath abandoned and working highwalls. Considering these situations, it seems to be worth introducing highwall mining systems into Indonesian open cut mines.Final highwalls of open cut mines can form the starting point for other mining methods, such as highwall or underground mining. In its basic application, highwall mining is a technique utilized after an open cut portion of a reserve has been mined, sometimes prior to the introduction of underground mining (Seib, 1993). In this system, the coal seam is mined by remotely operated equipment, such as an auger machine or a modified continuous miner incorporated into a highwall mining system. The major problems with highwall mining systems are less coal recovery due to leaving coal as the pillars and the instability of openings and highwalls due to the pillar and roof failures."

Jan 1, 2010

By Hamid Maleki

During the last decade, a significant amount of research has been conducted by Energy West Mining Company, government agencies, academia, and consulting companies to develop predictive tools for assessing the stability of the Castlegate Sandstone, which is found approximately 250 m above multiple-scam coal reserves, Energy West Mining uses longwall mining techniques in its operations near Huntington, Utah, and these studies were initiated to satisfy requirements for maintaining the stability of the Castlegate Sandstone and resource recovery. In this study, the authors have used multiple-regression analysis techniques and a wealth of data collected over many years on geology, mining, and escarpment stability. The volume of failed rocks is used as the response variable after several other factors were considered, including measurement of surface deformation and frequency of mining-induced surface fractures. Geologic and geometric variables were obtained along 3.7 km of escarpment exposure at 130 study locations. Regression analysis of data for the first 29 study location, which had been fully' undermined, showed that surface topography played a critical rule in influencing escarpment stability. Preliminary regression analysis results from 70 study loca¬tions identified several other important geologic arid mining factors that influence be stability of the sandstone escarpment These are canyon slope, sandstone thickness, and mining influence ante.

Jan 1, 2000

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Tom Barczak

Early in my career, while giving a presentation on shield design for longwall mining at one of the International Conferences on Ground Control in Mining, the late Jim Scott told me that I was finally getting it, because ?I was starting to think like a rock!? Although I didn?t realize it at the time, those few words changed my career forever. At the start of my career, I did a lot of laboratory testing, taking advantage of the unique capabilities of the Mine Roof Simulator to study the performance and design characteristics of longwall shields. I had a pretty good handle on what made shields work and what made them fail, but I was still struggling with how and why they develop their in-service loads and what they were actually controlling as opposed to being passive bystanders in a world beyond their control. It became clear to me that the simplistic models of dead weight loading could not explain the behavior I saw and measured underground. The problem did not go away when I started studying standing support systems. Again, I learned much about the strength, stiffness, and stability of these supports and helped the industry develop several new support products that attempted to provide more efficient support designs. But here, too, the simplistic models of dead weight loading did not seem to fit for me. That?s when I began to incorporate the ground reaction concept as a way of integrating the support response and the ground behavior into a cohesive design methodology. The concept has its limitations, no doubt, but I believe some form of it will be the future of not only designing supports but also, in the broader sense, enhancing the engineering aspects of ground control. The paper presented at the International Conference on Ground Control last year by Esterhuizen (2010) on pillar behavior is evidence of this. Think like a rock. Jim Scott was right. It takes two to dance. You can?t dance alone and you will never understand ground control by thinking like a support! ?Dumb as a box of rocks?? I don?t think so. The answer lies in the rocks!

Jan 1, 2011

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By Frederick Carr

1. The application of retreat longwall mining to the North American coal mining conditions is be¬coming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be the keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the col¬lapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The #3 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularly regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1982

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By David C. Oyler

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation, topping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented,

Jan 1, 2001

By Francis S. Kendorski

High-extraction mining of coal and other stratified minerals has a predictable effect on the surface and subsurface. Impacts on ground waters in overlying strata and on surface waters, that are associated with overlying sequential zones of collapse, fracturing, aquiclude, constrained strata, and surface disturbances can be anticipated. Since first quantified around 1979 in Bureau of Mines sponsored contract research work and others (and often adopted by state regulators), with zone extents based upon multiples of mined seam height of 24 to over 60 for the fractured zone, much new data have become available. In examining the sources of data and the methods and intents of the researchers of over 65 case histories, it became apparent that the strata behaviors were being confused with overlapping vertical extents reported for the fractured zones and aquiclude zones depending on whether the researcher was interested in water intrusion into the mine or in water loss from surface or ground waters. These more recent data, and critical examination of existing data, have led to the realization that the former "Aquiclude Zone" defined for its ability to prevent or minimize the intrusion of ground or surface waters into mines has another important character in increasing storage of surface and shallow ground waters in response to mining with no permanent loss of waters. This zone is here named the "Dilated Zone." The existence of the dilated zone explains the ratios of up to 60 times the mined thickness. Surface and ground waters can drain into this zone, but seldom into the mine, and can eventually be recovered through closing of dilations by mine subsidence progression away from the area, or filling of the additional void space created, or both. A revised model has been developed which accommodates the available data, by modifying the zones as follows: ? collapse and disaggregation extending 6 to 10 times the mined thickness above the panel ? continuous fracturing extending approximately 24 times the mined thickness above the panel, allowing temporary drainage of intersected surface and ground waters ? development of a zone of dilated, increased storativity, and leaky strata with little enhanced vertical permeability from 24 to 60 times the mined thickness above the panel above the continuous fracturing zone, and below the constrained or surface effects zones, whose thickness or existence is dictated by the zones above and below ? maintenance of a constrained but leaky zone above the dilated zone and below the surface effects zone, whose thickness or existence is dictated by the zones above and below ? limited surface fracturing in areas of extension extending up to 50 ft or so beneath the ground surface

Jan 1, 1993

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016