Search Documents

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the "advance and relieve" method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2001

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003

By D. L. Schweyer, W. A. Munson, R. H. Hanewald

Discussed is the INMETCO processing of electric arc furnace (EAF) baghouse dusts from the specialty-steel and low-alloy industries. In addition, the INMETCO process has been modified to recover nickel, chromium and iron from many other waste materials including: •pickling solutions or filter cakes, •spent nickel and chromium plating baths, •carbon refractories from pickling tanks, and •superalloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high-temperature metals recovery. This process and the details of INMETCO's best demonstrated available technology (BDAT) test program are discussed.

Jan 1, 1993

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering,(pp. 379-384), and as a document entitled "A Guide for Reporting Exploration Information, continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Re¬sources and Reserves and became a standing committee. Since 1994, the Council of Mining and Metallurgical

Jan 1, 1999

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By Jon Y. Kaneshiro, John S. Griffith, Anthony F. Stirbys, Mauricio Andrade

This paper presents an overview of the New Mississippi Tunnel Outfall for the Transportation Expansion Project (T-REX). The Outfall conveys highway and other urban drainage to the South Platte River as well as provides long needed relief from flooding problems in the southeastern portion of the Interstate 25 highway corridor. The Outfall tunnel incorporates a one-pass precast concrete segmented liner to convey storm water under I-25 then under Mississippi Avenue to the river. The Outfall crosses both the existing I-25 as well as the future improvements including under the Light Rail Transit, a new bridge abutment, widened lanes, and new retaining walls. The Outfall also crosses adjacent to several buildings and five bridges, under major traffic and utility intersections, and through difficult geology.

Jan 1, 2003

By Pengfei Wang, Guorui Feng

"With the depletion of easily minable coal seams, less favorable reserves under adverse conditions have to be mined out to meet the market demand. Due to several historical reasons, a large amount of remnant coal was left unrecovered. One such case history occurs with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Coal Mine, Shanxi Province, China. The challenge that the coal mine is facing is that there is an ultra-close coal seam right under it, with an only 0.8 to 1.5 m sandstone dirt band in between the two. The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving (LTCC). The remnant coal pillar was induced to cave in as top coal in LTCC system. Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata. The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars. The gob development (roof strata cave-in) is intermittent with the cave-in of these coal pillars and the sandstone dirt band. FLAC3D numerical modelling shows that the multiple seam interaction has a significant influence on mining-induced stress environment for mining of lower panel. The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found. This demonstrates that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below them.INTRODUCTIONChina is one of the world’s coal-rich countries. Coal has played a significant role in the growth of China’s economy. Coal reserves have been mined commercially in China for over one hundred years. The demand for coal in China is still going to grow at a relatively high rate (BP Energy Outlook, 2019). Long-term large-scale and intensive coal mining activities have created tension between increased demand and limited resources (Bai et al., 2018). Easily minable coal seams such as sub-horizontal, tabular, and laterally extensive coal seams are being depleted, and therefore the remaining reserves are becoming less favorable. However, in many situations, the coal reserves under adverse conditions have to be mined out to meet the market demand for energy.Due to sedimentary environments and geological conditions, many coal seams are interspersed with sedimentary bands, or partings both within an individual seam and between seams. These bands and partings lead to appearance of ultra-close coal seams, as well as giving rise to considerable variation in their structural and mechanical properties (Ghabraie and Ren, 2016). Difficulties are encountered in the mining of such coal seams. If ultra-close coal seams are mined sequentially, that requires the design of a mining system for each individual coal seam; also, a large number of gateroads have to be excavated, which is not a high-efficiency option. If ultra-close coal seams are mined at a great mining height at once, for instance, using longwall top coal caving—a longwall mining method that is widely used in China for the mining of ultra-thick coal seams—then the location and characteristics of the band would have a significant influence on success of their extraction."

Jan 1, 2019

By Yoginder P. Chugh

The Department of Energy is presently sponsoring the development of automated miner-bolter machines in an effort to increase production and productivity in the continuous room-and-pillar mining sections. This study is concerned with the production potential of these machines in three different mine layouts. The Underground Material Handling Simulation (UGMHS) computer model was utilized in the study. The effect of variables such as bolt installation delay, shuttle car capacity, and equipment availability on production are analyzed.

Jan 1, 1979

The implementation of NAFTA in January 1994 was expected to have small but beneficial effects on the Mexican economy, mostly through increased investments. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results during the past two years have shown that it is government and macroeconomic factors that influence investment flows, rather than the fine tuning of trade flows through so called “free-trade" agreements.

Jan 1, 1998

By Biao Qiu

Longwall and/or room-and-pillar mining operations in multiple coal seams could not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize mine structures and subsequently induce additional strata movements. Mechanical models to utilize the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations as well as the mining interactions associated with multi-seam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multi-seam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multi-seam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By Ronald E. Yarbrough, Theodore L. Triplett, Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from a high-extraction retreat room-and-pillar operation in southern Illinois. The objective of this monitoring program is to study the inter- action between the ground surface and a structure during a subsidence event. Data from such a study should enhance the understanding of the mechanisms that produce structural damage and aid in the design of structures that resist such damage. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tiltmeter to detect and follow the tilt of the foundations caused by the mining subsidence sequence is demonstrated. Using data from this tiltmeter, the development of curvature in the foundations as they conformed to the displaced ground surface is shown. This curvature is rep- resented by differences in tilt at various points on the foundations, indicating a change in tilt over a horizontal distance. Also, even though subsidence damage has not been fully analyzed, preliminary observations of the cracks that formed in the foundations are reported. These cracks resulted in the separation of one footing into distinct pieces; therefore, their effect on the tilt readings is cited.

Jan 1, 1986

By Z. T. Bieniawski, Christopher Mark

A new method for the design of long- wall chain pillars, called Analysis of Longwall Pillar Stability (ALPS), is described. The method provides estimates of the relative stability of different longwall pillar designs during all stages of their service life. The key issue addressed by ALPS is the magnitude and time-of-arrival of the longwall abutment loads applied to chain pillars. A field study was conducted and other available field data were analyzed in order to develop an approach for estimating the abutment loads. An example based on longwall experience in the Pittsburgh seam is used to illustrate how ALPS can be used in mine design.

Jan 1, 1986

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By N. Harrigle, Tsutsumi

Very fine wet sizing of minerals such as kaolin, precipitated calcium carbonate, lime milk, and clay slip is a difficult process to achieve using standard vibrating screens. With particle sizes ranging in the sub-microns combined with the agglomerating tendencies of certain materials, screen blinding becomes a serious issue. Sizetec, Inc. has developed an innovative screening equipment to help solve this problem. The High Performer Screen uses powerful linear vibrations to help break apart agglomerated particles and prevent screen blinding. Optionally fitted with the Air Explosion Screen Cleaning System, compressed air can be periodically injected into the screen underflow chamber to clean the screen surface without the use of water sprays. This paper highlights some of the key features of the Sizetec High Performer Screen and describes typical performance that can be expected based on results from various trials conducted in the kaolin industries.

Jan 1, 2002

By Y. C. Kim

For the past few years, the Cyprus Bagdad Copper Company began experiencing a significant "ore-dilution" problem from its low grade open- pit copper mine located at Bagdad, Arizona. To pinpoint the causes of this dilution, a study was initiated to investigate as well as to improve in-pit ore-waste selection-procedures using conditionally simulated ore-bodies. Prior to the actual use of conditional simulation; a comparison of different estimation methods for a mined-out area in the pit was performed. Specifically, kriging estimates were compared against the original estimates of the company which were based on the polygonal approach. The results of this comparison clearly identified part of the so- called "ore-dilution" problem, which was the initial over-estimation of average ore grades from blast rounds, using the polygonal approach. The results from the use of conditionally simulated orebodies demonstrated that the "ore-dilution" problem can be reduced by more than half if in-pit ore- waste selection is based on the kriged estimates rather than the polygonal estimates. This simulation study also showed that the current use of the polygonal approach has the effect of shipping a larger tonnage of lower grade material to the mill.

Jan 1, 1982

By T. P. Meloy

Understanding the illusive nature of the catastrophic failure of brittle solids is difficult. Proposed is a hypothesis of crack cessation. If, during catastrophic failure, cracks in a brittle solid stop before terminating on a preexisting crack, this hypothesis suggests that the slope of the size distribution curve will be lower. Moreover, this hypothesis suggests that when cracks stop, negative valleys and negative comers appear. Furthermore, particle shapes also change with particle size. While the hypothesis is unverified, it suggests that crack cessation could play a role in the comminution process.

Jan 1, 1996

By James H. Harmon

As the trend to deeper mines, producing from marginal ore bodies, continues, mine hoists and their associated equipment will become more sophisticated, complex, large and expensive. Over the past two decades, mine hoisting equipment and systems have moved from steam engines to static rectification of ac to dc, and electronic controls are the standard. It is the intent of this section to present what is currently available in the field of mine hoisting equipment and systems. Because the present engineer has been exposed longer and more intensively to such things as computers, electronic devices, and machine design, no attempt has been made to make this a layman's article. Contributions from the electrical design and application engineer, gearing and hearing design engineers and other specialists have been incorporated. Some material will be devoted to electrical drive systems, rectifiers and gearing design among others. These items are inherent in the design of a mine hoisting system and the subsequent selection of the correct, most reliable and most economic system. The mine hoist can be a bottleneck between the underground mine and the surface mill. Correct selection of the right type of hoist is imperative. In this vital link between mine and mill, crude estimates of hoist capacity are not good enough, and the mining engineer must design and select the right hoisting system to meet the design specifications. 15.1-MINE HOIST TYPES There are two basic types of mine hoists available anywhere in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Drum and friction hoists are "generic" terms which describe the two basic categories. Within each category are variations, as below. 15.1.1-DRUM HOISTS Drum hoists, as noted, actually store the hoist rope on the drum much the same as line on a fishing reel. To accomplish this task, the drums are so designed to store, in one or more layers, the footage of wire rope equal to the total maximum hoisting distance plus sufficient rope for cutting and inspection at regular intervals and for holding to the drum (see Fig. 15-1). Usual practice in hoist drum design is to allow three turns of hoist rope for holding on the drum and three turns for inspection cuttings. 1. Single-Drum Hoists-Fig. 15-2 shows a typical single-drum hoist as manufactured by most U.S. heavy-mining-equipment companies. With the exception of some very minor features, this design configuration is standard throughout the U.S.A. Fig. 15-3 is a plan view of a typical single-drum mine hoist. This particular hoist has a single-motor drive and a double-reduction set of gearing.

Jan 1, 1973

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972