Search Documents

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth's surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

By Douglas B. Silver

The key to unlocking value is to find opportunity where others have missed it. How does a company find value in a thoroughly explored asset? This article explores the approach taken by one company and the results it achieved from working this problem. The town of Shafter is located on a small bend in the road in west Texas' Big Bend Country. Its past emulates the glory days of so many other mining camps. A discovery was made, fortunes were built and World War II shut down the operation. The Shafter deposit continues to be one of the larg¬est undeveloped primary silver deposits in North America. Gold Fields Mining Co. recognized the area's potential in 1977 and embarked on studies to reopen and develop the district. Gold Fields spent $16 million on the Shafter project. It drilled more than 86,240 m (282,940 ft) in 475 holes, sunk two shafts and developed 1,550 m (5,100 ft) of underground workings. Today, the mothballed 447-kW (600-hp), single-drum Nordberg hoist and permanent production-type, single-compartment headframe continue to crown the shaft. Other buildings onsite house compressors, mine pumps, spare parts, drill core and other supplies. All these items look as though they arrived yesterday. By 1982, Gold Fields had completed an extensive feasibility study with ambitions to. construct a 1.36-kt/d (1,500-stpd) agitated cyanidation mill and base metal gravity circuit. Reserves at Shafter stand at 4.23 Mt (4.67 million st) grading 193.5 g/t (5.65 oz/st) silver. Gold Fields planned to produce 71.5 t/a (2.3 million oz/year) of silver at a head grade of 196.2 g/t (5.73 oz/st) silver with a 77% recovery rate. Cash costs were projected to be $5.54/oz with an anticipated initial and total capital cost of $46.2 million and $51.3 million (1984 dollars), respectively. The study assumed a silver price of $8.60/oz that has not been seen since the Hunt brothers quit buying silver. When silver prices declined, Gold Fields put the property up for sale.

Jan 1, 1999

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By William P. Lorenz

The paper describes a uranium by-product recovery plant operating within a copper leach, solvent extraction, and electrowinning circuit. The operation is unique because it is integrated into the main process stream of the copper circuit The plant processes 1408 m3/h of copper solutions containing about 10 mg/L of uranium. An Eluex type process was selected due to its compatibility with the copper leach plant. The paper includes an overview of the copper circuit

Jan 1, 1983

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By Dave Rogstad

The DART NC-1B Tunnel Project consists of two 5,100 m TBM excavated tunnels, a principal underground station, a partially completed future station, a surface station, and eight associated ventilation shafts and exit tunnels. This paper presents a case history of the project's construction, and will focus on six topics that give this project a unique and unusual history; the TBM excavation, two major differing site conditions, roadheader excavation, polyfiber reinforced shotcrete lining, the NATM design geometry, and a design/build type of contract.

Jan 1, 1995

By J. R. Johnson, C. G. Stewart, D. K. Myers

INTRODUCTION Radon-222 is an inert, radioactive gas formed by the radioactive decay of radium-226, a long-lived member of the uranium-238 decay chain. Radium is present in varying amounts in virtually all soils and, on the average, about 36,000 pCi (1330 Bq) of radon per square meter of soil diffuse into the atmosphere each day (UN 1977). Radon decays with a half-life of 3.6 days through four short-lived daughters to lead210 and it is these short-lived daughters[ [Ra A, (218Po, t, = 3.0 min) , Ra B, (214 Pb, t;, = 27 min), Ra C, (214Bi, t] = 20 min) and Ra C1 (214Po, t] = 2.5 x 10-6 min)] ]which cause the major health hazard associated with radon (Bale 1951). Atoms of these daughters, either unattached or attached to the ever-present particles in air, are deposited on the surfaces of the respiratory tract; alpha particles emitted in their decay can result in large doses to the cells of the bronchial epithelium lining the respiratory tract. These daughters will be present in air in varying relative concentrations depending on the "age" of the air (time since radon emanated into it) and on the amount of mixing of radon and radon daughter contaminated air with clean air. [The practical unit developed to quantify the amount of radon daughters in air is the Working Level (WL). This unit was historically related to the equilibrium concentration of 100 pCi (3.7 Bq) of the short-lived daughters of radon in one liter of air (cf. Holaday 1969) and is defined as any mixture of the short-lived daughters in a liter of air that have a-potential alpha energy of 1.3 x 105 Mev (2.08 x 10-5J) in their decay to lead-210. The working level month (WLM) was developed along with the WL, and was defined as an exposure to one WL for a working month (170 h). This is equivalent to 2.2 x 107 MeV•h•L-1 (3.54 x 10-3 J.h.m-3). If the average breathing rate is taken as 1.2 m3.h•1 (ICRP 1975), then one WLM is equivalent to inhalation of 4.24 mJ of potential alpha energy.] It is now generally agreed that the inhalation of radon daughters is the major potential radiation hazard in uranium mining, and contributes a substantial fraction to the natural radiation exposure of the general population due to the accumulation of radon and radon daughters from natural sources in buildings. Radon daughter concentrations in modern mines are controlled by ventilation, and by blocking off old working areas (cf. Simpson, 1959). However, before the hazard from radon daughters was recognized, considerably higher concentrations of radon daughters were present in some uranium and non-uranium mines. These high radon daughter concentrations resulted in an increase in lung cancers in the mining population, and it is these results that are our main source of information on the risk of inhaling radon daughters. HISTORICAL REVIEW Many excellent reviews of the history of understanding the health effects of inhalation of radon daughters are available (see, for example, Hueper 1942, Lorenz 1944, Sikl 1950, Stewart 1964, Holaday 1969, Lundin 1971, Cross 1979) but a brief summary of some of the highlights in this area may be of interest. [a] 1556: Agricola describes an unusual and fatal chest disease occurring among underground miners in the region of Schneeberg and Joachimsthal (Jachymov) in the Erz mountains in Central Europe. (It is of some historical interest to note that Agricola's book was translated from Latin into English by a mining engineer and his wife; the engineer later became President of the U.S.A.) [b] 1879: Haerting and Hesse indicated that the majority of deaths among Schneeberg miners were due to lung cancer; the lung cancers in these miners (who were incidentally not cigarette smokers) were observed twenty to fifty years after they began working in the mines. [c] 1896: Discovery of natural radioactivity by Becquerel, followed by discovery of radon by Dorn in 1900. [d] 1924: Ludewig and Lorenser report high concentrations (400 - 15000 pCi or 15 - 570 Bq per liter) of radon in the air in the Schneeberg mines and suggest that radon could be responsible for the high rate of lung cancer among miners. However, the reason why radon should cause lung cancer specifically was still not really understood up to twenty years later (Lorenz 1944). High concentrations of radon in the air in the Joachimsthal mines were reported by Behounek in 1927 and a high incidence of lung cancer among Joachimsthal miners (similar to that among miners at Schneeberg, which is only some 30 km distant but in a different political district) was noted at about the same time (Sikl 1930; cf. Sikl 1950). It is estimated that about half of the Joachimsthal miners died from lung cancer and about half from silicosis and tuberculosis (Sikl 1950). [e] 1930's and 1940's: Radioactive ores are deliberately mined in the U.S.A., Canada and other countries primarily as a source of radium for medical purposes and for luminescent dials; other radioactive ores are mined as a source of several non-radioactive minerals, while extensive uranium mining did not begin until the late 1940's. [f] 1940: Based on crude epidemiology and dose calculations, Evans and Goodman propose 10 pCi L-1 as a maximum permissible concentration of radon in continued human exposure. This is the first known recommended maximum permissible concentration for radon. This recommendation was adopted by the U.S. National Bureau of Standards in 1941 and reconfirmed in 1953. [g] 1945: Mitchell identifies the short-lived daughters in radon as a likely cause of the increased lung cancers in the Schneeberg-Joachimsthal miners

Jan 1, 1981

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

The classical slope analysis and a statistical technique were used in order to determine the iron complexes formed in the organic phase during the extraction of Fe(III) from Fe-Ni-Co sulfate solutions with Di-(2-ethylhexyl) phosphoric acid (D2EHPA) in kerosene. Equilibrium constants for the extraction based on these complexes were also calculated. The complexes determined were of the general form (Fe(OH)3-nRn?sHR)x' where n varied between 1 and 2.5 and s between 0 and 3, and both were found to be decreasing as the iron loading in the organic phase increased. Values of 1,2 and 3 were generally found for x, indicating that the complexes were monomers, dimers and trimers.

Jan 1, 1988

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

An incremental-analysis-based stope design and cutoff grade calculation method was developed for an underground metal mine project. Traditional stope design methods are typically very time consuming and lack consistency and accuracy by manually drawing stope shapes. For quick reserve calculation and economic analysis, a new method named "3D incremental analysis based stope design" was created for mine-wide stope designs. The key idea of this method is to replace engineers' manual checking of each incremental ring with one calculation of all the rings, and to build the final stope shape with the maximum values. This process was realized through a 3D ring grid setup and proper naming conventions for rapid calculations. With this unique but practical method, multiple options for a mine design were completed within a short time before the final selection of optimal cutoff grade and best stope designs for the project.

Jan 1, 2012

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By A. J. Hendron, B. Mohraz, R. B. Peck

INTRODUCTION The state of the art of soft-ground tunneling was discussed in detail by the senior author at the 7th International Conference on Soil Mechanics and Foundation Engineering held in Mexico City in 1969. Little can be gained by repeating the information assembled at that time. Hence, in this report, only the briefest summary will be given of the overall state of the art and attention will be concentrated on trends and developments since 1969. A characteristic of recent developments is the continued trend toward use of shields and excavating machines. The implications of this trend with respect to design and construction, and particularly with respect to the treatment of unfavorable ground conditions, will be examined. Settlement associated with lost ground, a subject as old as tunneling itself, will be reviewed and methods will be considered for its reduction. Design of tunnel supports was discussed in detail in 1969 with respect to essentially rigid or essentially flexible types of linings. In this report, a definition of flexibility will be considered and design procedures suggested for linings of flexibility intermediate between the two extremes.

Jan 1, 1997

By M. Sheppard, P. Wand, G. A. Cooper, M. Lesage

The vibrations generated by a tricone drill bit are caused by the successive impacts of the bit teeth on the rock, and peaks in the vibration spectrum can be associated with impacts coming from particular rows of teeth on one or other of the bit cones. Wear of the bit teeth causes a shift of these peaks to higher frequencies at constant bit rotary speed, whereas changes in rock type generally produce changes in peak height. Bit bearing failure or poor hole-bottom cleaning both cause loss of definition in the spectrum, the latter often associated with spurious high-amplitude signals at low frequency. The vibration signals may also be analysed in the time domain, where, for example, cone locking can be identified by characteristic features in the signal of torsional acceleration.

Jan 1, 1987