Search Documents

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By T. S. McGahey

The southeastern region of the United States has long been a major market area for coarse and medium particle size natural ground calcium carbonate fillers. The primary market for calcium carbonate in the southeast traditionally has been as fillers in building materials such as carpeting, joint cement and roof shingles. In these applications the economic value of the calcium carbonate in the final product is weighted more toward lessening the cost of the final product, as opposed to contributing any desirable physical characteristics. For example, in carpet backing applications the calcium carbonate filler does little more from a physical standpoint than add weight and body to the backing adhesive. The important factor in the use of calcium carbonate in carpet backing is that it can be used at high loading levels to replace the more expensive latex binder, thus lessening the cost of the final product. It is estimated that calcium carbonate producers in the southeast sell in excess of 200,000 tons (181,436,000 kg) annually for use in latex compounds for carpet backing applications.

Jan 1, 1986

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999