Search Documents

By L. M. Pero

The paper summarizes aspects of the recent literature on mineral development in the Third World. The emphasis is on publications covering agreements between host governments and mining companies.

Jan 1, 1985

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By V. P. Petrov

There is a great number of asbestos deposits in the USSR. Some of them are quite large ones. The main deposits of chrysotile asbestos can be seen in the sketch map (fig. 1). Bazhenovo deposit situated in Sverdlovsk region is the largest of them. It is on mining operations since year 1889. Systematical studies of asbestos deposits were begun from the first years of Soviet Government and connected with the names of K.E. Tarasov, P. M. Tatarinov, B. J. Merenkov, N.D. Sobolev, F. V. Syromjatnikov, V. N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V. R. Artemov, V.F. Dybkov and many others. This investigations served the USSR to be one of the most important producers of asbestos in the world. In the limits of the report a characteristic of the main asbestos deposits of the USSR may be done in general outline, from the point of view of their genesis, and in order to show their common features and differences that must be taken into account for forecasting, exploration, and mining of asbestos. All chrysotile asbestos deposits of the USSR were formed of magnesium rock as a result of comparatively lower-grade temperature hydrothermal alteration and free crystallization of fibrous chrysotile in open cavities that served as catalyst As a matter of fact an important mineral for industry is not chrysotile in general, a widely distributed rock-forming mineral, but a long fibrous and mainly vein variety of chrysotile. It must serve for geologists as an important prospecting criteria. A geologist should search for the mineral not only places of possible chrysotile generations, but places where asbestos may be crystallized in its long fibers that could be fiberized well. The Soviet geologists distinguish two groups of chrysotile-asbestos deposits: (1) related to ultrabasic rocks and (2) related to sedimentary dolomite terranes, taking into account what the maternal rock was affected by hydrothermal solutions. The largest deposits related to ultrabasite. The largest deposits in dolomite are small ones but their asbestos contains almost no iron. So much asbestos is a better filler into insulating plastics. There is a few types of asbestos deposits in the limits of the ultrabasic group. The largest of them is a Bazhenovo type which the deposits of Urals are attributed, and Bazhenovo deposits is the first instance. The Bazhenovo type is characterized by the most complete zonality in disposition of various kinds of asbestization. This type of deposits is practically the only one to be in working now in the USSR.

Jan 1, 1978

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By B. Hester

Many Third World countries of Third World Africa are well-endowed with minerals, especially gold. Political and economic conditions discouraged interest by Western capital for the several decades since colonial rule. Influence from Eastern Block countries has gone and the left wing orientation widely favored by Third World countries has almost disappeared. Under International Monetary Fund influence, these countries now solicit Western finance to expand their industries. Mining is especially encouraged. The paper describes the financing of some recent developments and examines trends and opportunities in some of the more attractive countries.

Jan 1, 1993

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By T. Murt, C. Oñate

In recent years, environmental considerations have played a prominent role in underground construction projects. The management and disposal of the muck produced by an EPB TBM is an important aspect of this topic. Soil conditioners with higher biodegradability and lower eco-toxicity have been specifically developed to comply with strict regulations in several countries around the world, with the goal of reducing the environmental impact of tunneling on soil, water, and living organisms. This paper highlights innovative sustainable soil conditioners and how they differ from traditional products. Additionally, environmental considerations for TBM projects around the world and in North America will be examined.

Dec 1, 2022

By S. Borner Schweizer

An overview over SAM’s approach to assess corporate sustainability performance illustrates how sustainability challenges are linked to trends, assessment criteria and finally company performance. This process is exemplified with some general and industry specific criteria. Lastly, results of the Dow Jones Sustainability Assessment 2004 show a considerable gap between leading and average companies. Best practice examples demonstrate how lagging companies could improve their sustainability performance.

Jan 1, 2005

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By M. Javier

Management is a major part of sustainability research. Many different aspects of sustainability have already received significant research attention, but the management processes in mining from the perspective of their impact on society are less understood and integrated as a holistic frame. It is evident that mining technology has received major blame in past ecological disasters and major mining-induced environmental hazards, but the management-mining process has escaped unscathed. This should not have happened. Instead, the management processes should share equal blame with obsolete technology for the failure to identify and monitor potential environmental hazards before their inception of mining. We will present an emergent style of management for the future of mining. It challenges the actual ?mind-set? of mining management. It describes balance and equilibrium: physical, chemical, and biological in nature as an understanding of nature?s language, which is Geomimic along side ?the bottom line?. The goal is to minimize loss instead of maximize profits (waste design) at the design stage of mining and to develop clean technologies (nature's values) to achieve non-social environmental impacts that provide a prosperous legacy to future generations.

Jan 1, 2010

By Ginger L. Hustrulid

Conveyor belts are a critical component in tunneling projects. This paper reviews current design considerations for conveyor belts. Rubber compounding differences to meet local fire resistance regulations or certain cover characteristics such as higher abrasion resistance or low carbon footprint rubbers for applications are reviewed. Evaluation of fabric belts, steel cable belts and the benefits of each carcass design for a particular use is also examined to help with proper carcass selection to decrease downtime from unexpected failures. Finally, this paper takes a look at some of the differences when working in metric versus imperial units.

Dec 1, 2022

By Stephen L. Chryssoulis

The detection and quantification of invisible gold by microbeam techniques is discussed. Ion probe microanalysis is used to quantify the gold content of individual sulphide, sulpharsenide and oxide particles with a detection limit of 0.2 ppmw (g/t). The proton microprobe is used to determine the gold concentration of gangue minerals with a detection limit of 2 - 4 ppm. Using these techniques complete mineralogical balances for gold are obtained to assist in the process selection and optimization. A total of twenty gold and gold-bearing ores have been examined. Selected examples are presented.

Jan 1, 1990

By YOUNIS S. MUSTAFA, GHORASHI ZAIN, ABDEL-ZAHER M. ABOUZEID, AHMED A. S. SEIFELNASSR

The present paper attempts to characterize the breakage properties of a brittle rock, quartz, at different size fractions when compressed at various loads in a confined piston die.  This is to understand the interaction between the various parameters affecting the breakage behavior of a brittle solid in a confined zone. Application of the results may lead to improving the energy efficiency in the size-reduction units, which use compression as the main stressing force. 

By R. E. Blair

The mining and minerals industry has been, and continues to be, at the cutting edge of high technology. Iron and steel built the Industrial Revolution/copper electrified the world/coal tars and petroleum and gas feedstocks developed the organic chemical industry. Industrial minerals now carry forward this tradition. Two, of hundreds of examples of hi-tech industrial minerals are quartz crystal and rare earths. Both demonstrate the international market aspects of mining, processing and finished product trade.

Jan 1, 1988

By P. Albert Carpenter, Wallace B. Howe, Michael N. Greeley, E. C. Bingler, Gilbert R. Eakins, Christy Bell, John Callahan, Gary B. Glass, T. J. Crabs

Although gold's market price dropped considerably from 1980's all time high, exploration for the precious metal remained a particularly bright spot last year, especially in the western US. For example, in Nevada-the nation's largest gold producer-further exploratory drilling at Louisiana Land & Explorations Co.'s deposit at Round Mountain and Newmont Mining Corp.'s find near Carlin resulted in sharp boosts in estimated reserves at both sites. Louisiana Land said its deposit is well on the way to being one of the largest gold reserves in the US. Based on further drilling, Newmont said its Gold Quarry property near Carlin could now produce 4.7-6.2 t/a (150,000-200,000 oz/ year). Reserves at Newmont's two properties near Carlin and a third property in southeast California are reportedly at least 218 t (7 million oz), up from the previously announced 128 t (4.1 million oz). Gold exploration activities were brisk in many other states, including a noticeable effort to explore and reopen dormant properties. Although the return on investments didn't appear as favorable last year as they did in 1980, the gold price was apparently sufficient to spur healthy exploration activity. Outside precious metals, market conditions, and subsequent exploration activity, appeared much more bleak. In the molybdenum market, for example, prices continued to slide, and Amax Inc. tightened its exploration budget. (Amax supplies 60% of the domestic market and 45% of the world demand for molybdenum.) The company spent 16% less on exploration during the first six months in 1981, compared to the same period in 1980. Copper and many other base metal producers appeared in similar straits throughout the year. Uranium exploration activities continued to suffer last year also due to depressed market conditions. Among others, Gulf Minerals Resources and Amoco Minerals Co. suspended uranium exploration activities in the West. Despite current unfavorable conditions, some companies continue uranium searches, confident that market conditions will rebound. On a brighter note, interest in exploring for some industrial and strategic minerals appeared on the upswing last year. Minerals used for oil and gas drilling, such as barite and special sands, were especially noteworthy. In geophysical activity, significant developments were achieved for electromagnetic techniques in both frequency-domain and time-domain systems. Geophysical logging activity declined due to decreased uranium exploration, and computer hardware continued to impact the way mining geophysical data are being acquired. Many presentations and papers were given last year to help exploration geochemists develop new techniques to locate concealed ore bodies. Among techniques described were statistical and computer modeling for enhancing anomalies over blind deposits.

Jan 5, 1982

By Nelson R. Shaffer

Secondary minerals, amorphous materials, and biologic entities that form on building stone can cause aesthetically unflattering changes in color and may even result in stone decay. Techniques to determine causes of such changes generally have entailed destructive sampling and often required chemical, thin section, X-ray, or other relatively slow, expensive measurements. We have found that a rapid leach of in-place stone using small volumes (50-100 ml) of very pure distilled, deionized water provides recovery of sufficient dissolved material to help diagnose stone anomalies. Water is sprayed onto the stone and collected in a nonwetting plastic pan. Ion chromatograph analysis of waters thus collected from more than 160 sites showed wide variations in concentration of anions F, Cl, NO3, and SO4. Anion analyses were made in minutes for less than $20 per sample. Cations Ca, Mg, Fe, and Sr also were detected, and analyses might be used to determine mineral sources using equilibrium computer models. Solid particles filtered from the samples can be examined microscopically to provide further information about atmospheric agents affecting the stone. The collected water can even be evaporated to precipitate dissolved minerals. Chloride values in samples rinsed from stone ran as high as up to 17,000 ppm, nitrate to 100 ppm, and sulfate to 1,000 ppm. Limited data also indicate that measurable amounts of fluoride were found in some of the rinse waters. Chlorides were most abundant in areas where the stone has become dimpled or spalled. Nitrates were generally higher near ground level, and sulfate tended to be more abundant in samples taken from higher sites or from sheltered sites. Dark-stained limestone tended to yield less soluble material than clean-looking stone. Leachable elements were higher in samples from urban areas. Most of our data are from limestone buildings, but the technique works on other types of dimension stone, man-made construction materials, and even natural outcrops of rocks. Longitudinal studies show that soluble materials vary through time and are affected by climate. This rapid, in situ leach technique, although still being perfected, shows great promise in the diagnosis of stone alteration and in the evaluation of stone treatments because it is completely nondestructive.

Jan 1, 1999

By Justin Kolster, Donald Benjamin, Kyle White

Expansion of the Plum Island Wastewater Treatment Plant requires interconnection of three operating pump stations using only two existing 10-ft diameter shafts for access. These two existing shafts require additional support to allow access 130 feet below grade. Interconnection requires rehabilitation of an existing tunnel, excavation of two new tunnels, and abandonment of additional existing tunnels. Construction has discovered unexpected conditions at all three connection points. The CMAR contracting method has effectively accommodated project team discussion, value engineering decisions, and allocation of risk during preconstruction and construction phase services.

Dec 1, 2022