Search Documents

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By H. K. Lin

Residual cyanide in cyanidation tailings can be detoxified by its oxidation to cyanate, as in the Inco and Degussa processes. However, cyanate, the product of detoxification and other oxidation processes, may be reduced to cyanide in reducing environments, e.g., deepwater discharge of cyanidation tailings. This study shows that the reduc-tion of cyanate to cyanide occurs and that the reduction rate increases with decreasing solution redox potential. Solutions with lower pH favor the reduction rate. No significant difference was observed between the results of tests prepared with distilled water and seawater, and the presence of cyanidation solid tailings does not show an effect on the reduction. Because cyanate can be reduced to toxic cyanide, causing environmental concerns, the deepwater discharges of cyanidation tailings must be handled carefully.

Jan 1, 2008

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Michael Feroz, Marcus Jensen, James E. Lindell

The Southern Nevada Water Authority (SNWA) operates two water-intakes in Lake Mead, located 20 miles east of Las Vegas, Nevada. Severe drought has caused decline in lake level by 85 feet since 2000 and future declines are expected. SNWA will construct a third deep-water intake to ensure existing water system capacity. This paper describes expected construction challenges for the new project that consists of: an intake structure and tunnel beneath the lake, pumping station, pipeline to connect existing treatment facility, and interconnecting underground adits. The project will be completed in the year 2012 for total estimated cost of approximately $600 million.

Jan 1, 2007

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By Douglas R. Cook

Exploration record In preparing this paper, a list of world class discoveries prepared in 1983 has been updated. In both surveys, the following criteria were used in the definition of world class discoveries: • deposits that are continuously operated and consistently return a profit even in periods of low metal prices; • deposits large enough to significantly affect a medium sized corporation's profits; and • these deposits should be in the lower one-third cost per unit of metal produced for all similar deposits. Only 70 discoveries in the last 40 years qualified as world class deposits using these criteria. Unfortunately, this restricted population was too low to develop meaningful trends. The numbers were therefore enlarged to include all significant discoveries. The principal feature of a significant discovery is that its size and grade would yield more than $500 million in revenue using average metal prices for the last five years. A significant deposit should also meet some of the standards for a world class deposit. A tabulation of these deposits are shown in Table 1. The number of discoveries increased to 166 from 70 using the revised classification. The relationship between the number of discoveries per year and their location by continents was prepared from these data. Figure 1 shows the number of discoveries per year for the nonCommunist world. It also shows estimated and actual nonCommunist world exploration expenditures per year and the commodity price index. These data show that modern exploration started in the late 1940s, with the tempo picking up rapidly in the 1950s. The maximum discovery rate occurred in 1962. Thereafter, the discovery rate gradually declined to the present. This occurred despite a real increase in expenditures from about $200 million/a in 1955 (1982 constant dollars) to more than $900 million/a in 1980. Thus, these data suggest a significant decrease in the exploration success ratio (total exploration expenditures a year divided by the number of significant discoveries) in the last 20 years. As an example, $70 million was spent for each significant discovery in the early 1960s as compared with $225 million in the late 1970s (expressed in 1982 constant dollars). However, with the general declining trend of discoveries, one can perceive a more pronounced drop in 1973 and then a sudden increase in 1974, 1975, and 1976. This increase is probably related to the inflation of the 1970s that in turn created an environment for the explosion of commodity prices, as shown by the commodity price index on Fig. 1. Thereafter, the decline in discoveries resumed in 1975 until the present. Exploration performance by regions North American discoveries are shown in Fig. 2. The graph shows three pronounced high discovery peaks in 1962, 1975, and 1980-81.

Jan 2, 1986

By Staff

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages—basic (mining), intermediate processing, manufacturing of finished goods and construction. The estimated growth rate for the real GDP of the United States for 2006 was 3.2 percent. The nominal GDP was about $13.2 trillion. The value of minerals mined in the United States in 2006 rose significantly because of increased unit price for some metals—particularly copper, zinc and other base metals. There was also a significant reduction in metals stocks. Infrastructure expansion and manufacturing in China and India have been absorbing a significant portion of world output. Domestic production increased for some industrial mineral materials, mainly cement and construction sand and gravel. Production of crushed stone declined less than 1 percent in 2006 compared

Jan 1, 2007

By D. van der Veen

Mining companies and contractors are looking at Wirtgen Surface Miners to provide flexibility at their operations. Wirtgen Surface Miners have been used in the surface mining industry for over fifteen years. The principle behind the Wirtgen Miner is a rotating drum equipped with tungsten carbide tipped cutting tools that excavates and sizes the material. The drum helix augurs the mined material to the center of the drum where it is loaded onto the primary conveyor belt. From there the material is conveyed to the discharge belt and into a truck bed. The cutting drum is located in the center of the machine, near the center of gravity. This permits the machine to cut hard materials as the entire machine weight is converted into cutting forces. Conventional mining practices are process, equipment, and labor intensive. Furthermore, strict environmental requirements pertaining to noise levels, dust pollution, and blasting, near buildings or urban areas, limit the application of conventional methods. Mining/ Construction contractors are using Wirtgen Miners in various limestone excavation projects, such as highway expansion projects, and new roads in housing developments. Mining companies in the industrial minerals and coal industry are using Wirtgen Miners to load directly onto trucks, eliminating the rehandling process and ultimately, primary crushers.

Jan 1, 2002

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007

By M. H. Dunn, T. P. Danehy, C. F. Denholm, S. L. Busler

The problems associated with abandoned minelands are so extensive that neither federal, state, or local governments nor the mining industry nor watershed groups can adequately address these problems individually. By combining talents and resources, however, these problems are being solved efficiently, effectively, and economically. Utilizing existing water monitoring data, local public-private partnerships have successfully designed and built passive systems within five weeks to six months which treat discharges up to hundreds of gallons per minute that vary in quality from net alkaline to highly acidic, containing as much as 200 mg/L dissolved iron and 70 mg/L dissolved aluminum.

Jan 1, 2002