Search Documents

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Nenad Spoljaric

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite. The word glauconite is derived from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was mined and marketed as a natural fertilizer and soil conditioner for more than 100 years. The advent of manufactured fertilizers with adjustable nutrient ratios led to a decline in the use of greensand in agriculture. The material has since been recognized as useful in water treatment. Unfortunately, despite large reserves and world- wide distribution, glauconite has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This is probably due mostly to a paucity of research on its potential commercial uses. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and a generally low potash content (viz., less than 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of as much as 22.5 kg/m2 were sometimes made, although recommendations for agricultural use suggested 4.5 to 11 kg/m2 (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of its slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as poison, burning, or black marls. The availability of higher grade potash salts from other mineral sources and the manufacture of prepared fertilizers displaced the agricultural use of greensand during the latter 1800s. During the mid-1800s the greensand industry, centered in a small section of the eastern United States, grossed more than $500,000/y. Toward the end of the century, however, annual production had dwindled to less than $100,000 in value. By 19 10 there were only six or eight greensand producers grossing less than $5,000/y each (Tyler, 1934). There was a brief revival of the US industry during World War I because of the curtailment of foreign potash, especially from Germany. During the latter 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base exchange properties would release trace elements. For a short time glauconite was used in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s it was used for making green glass (Cook, 1868). In the early 1900s the base exchange properties of glauconite were recognized for water treatment and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base exchange even though this phenomenon was known in 1916 or earlier. From 1916 through 1922 several patents for the use of glauconite as a water softening agent were granted. A method was also patented for treating greensand to improve it for water softening and ready regeneration with common sodium chloride brine (Borrowman, 1920, Spencer, 1924, Kriegsheim and Vaughan, 1930). Treated glauconite, on contact with water containing magnesia or lime, takes up magnesium or calcium ions and releases sodium ions. This exchange is limited to the outer surface of glauconite grains, and when all the surfaces have absorbed their capacity, the grains must be regenerated. Regeneration, simply stated, consists of treating or backwashing the glauconite with a sodium chloride solution, which replaces the hard water elements with sodium, thus reviving the glauconite. The process has become more sophisticated due to competition among companies in the water softening business. Greensand products for water softening generally consisted of several different grades distinguished by the particular treatment the glauconite was given during processing. The standard greensand water softener was produced from natural glauconite that was only washed and classified. Its characteristics for water softening are given in [Table 1].

Jan 1, 1994

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alterative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements In the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms who optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 1999

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By F. Grajales Munoz

The Cienega project, now under construction by Penoles group, is located in the mountains of the State of Durango, Mexico. The gold and silver deposits are found in the 4-km long system of veins, which will be extracted by underground methods. The planned 1000 tpd process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994.

Jan 1, 1994

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By Shosei Serata

In the past, salt cavities for storage of liquid and gaseous fuels have been developed and operated using practical experience as a guide rather than rock mechanics principles and practices. Although many salt cavities are still operating satisfactorily. some of them are beginning to show various problems associated with long-term deterioration of the cavities. This paper describes a major breakthrough in the rock mechanics design of solution cavities which is the development and application of the REM computer simulation system. From the computer simulation analysis, the long-term deterioration process of cavities can be related to the basic parameters of rock mechanics design and the storage operations. The computer simulation system is also used for optimizing cavity design and operational specifications. This optimization technique is explained by its application to the three basic storage systems: 1) open dry storage system for liquids and solids 2) open wet storage system for liquids 3) pressurized storage system for gases, liquids and solids The effectiveness of the optimization technique is illustrated with some field examples by showing the direct interaction between the computer simulation system and field data of a test well including tectonic stress conditions, material property coefficients and geological anomalies.

Jan 1, 1974

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By Michael Schmalzel

Freeport-McMoRan Copper & Gold, Inc. (FMI) will soon begin copper production from the Dos Pobres and San Juan deposits near Safford, Arizona. Ore reserves total 615 M tons grading 0.36% copper, predominantly as chrysocolla. Copper extraction will be by leaching with sulfuric acid. Fluor Canada Ltd. provided EPCM services to design an ore handling and conventional SWEW facility capable of producing a nominal 240 million pounds per year of cathode copper. The ore handling facility will process 114,000 tons per day of ore through three-stage, open-circuit crushing followed by agglomeration and product placement on the permanent leach pad. Stacking of ore on the leach pad will utilize Terra Nova Technologies' "Super Portable" mobile stacking system. The stacking system fleet consists of 13 self- propelled, crawler-mounted mobile conveyor units, each with 72-inch-wide belting and a capacity of 6,800 tons per hour, including ten 250-foot-long portable conveyors, a horizontal feed conveyor, a 285-foot-long horizontal conveyor and a 220-foot-long radial stacker. PROJECT BACKGROUND Project History The Safford Leach Project is located in the Safford mining district in Graham County, Arizona, approximately eight miles northeast of the town of Safford and 170 miles east of Phoenix. The 3,360-acre property is located in the Gila River Valley, immediately south of the Gila Mountains, at elevations between approximately 3,000 and 5,400 feet above sea level. The Safford Leach Project is comprised of the Dos Pobres and San Juan deposits, two of five known copper ore deposits in the Safford mining district.

Jan 1, 2008

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By D. Berberick

Hecla?s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d?Alene mining district of northern Idaho. Main access into, and production from, the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk by J.S. Redpath to an original depth of 1,890 m (6,200 ft) in the early 1980s. The shaft is divided into four compartments (Fig. 1), with sets made of 225 mm x 175 mm (9 in. x 7 in.) hollow structural section (HSS) steel buntons and 150-mm x 150-mm (6-in. x 6-in.) HSS dividers spaced every 4.5 m (15 ft) down the length of the shaft. Two skip compartments on the east side of the shaft are equipped with 125-mm x 150-mm (5-in. x 6-in.) HSS steel guides and 9-t (10-st) skips with three deck trailer cages for men and materials. The west side of the shaft is divided into a manway, and a fourth compartment that was originally designed for a service cage. Shaft services consist of a 250-mm (10-in.) a compressed air line and 150-mm (6-in.) sandfill line along the south side of the shaft, and 250-mm (10-in.) discharge (gray) water and 150 mm (6 in.) fresh water lines on the north wall. The mine?s primary 13.8 kV power lines, as well as communication lines are located on the west wall of the shaft. The production hoist is a 3.7-m (12-ft) diameter, double drum, double clutch, 2,238 kW (3,000 hp), direct current unit equipped, at the time, with thyristor drives. The 30-year-old drives would prove to be problematic during the rehabilitation project, leading to an upgrade to modern ABB drives later in the project, after the shaft rehabilitation was complete. The shaft had been subjected to the typical wear and tear of 30 years of operation, including intermittent sandfill and muck spills, and, in the lower areas, some corrosion. During those 30 years, the west compartment, originally designed for the service cage, could only be accessed from a work deck on top of the skips or from the manway.

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By Stacey Leichliter

The Cripple Creek and Victor (CC&V) Gold Mine (Cresson Project) (Fig. 1) is undergoing an expansion to extend production to the year 2025. This expansion involves building a high-grade ore mill, another valley leach facility (VLF) for heap leach operations and expanding the overburden storage areas. The current operating pits are progressing downward from the oxide ore into a more sulfide and telluride-rich orebody. There is still oxide ore present in the current pits and planned pits not yet mined. There is an increased need for two recovery processes for these two different types of ore. The key component to this expansion is the high-grade ore mill, which has gravity, flotation and carbon-in-pulp (CIP) circuits. The mill will be the main recovery process for the higher grade, more sulfide/telluride-rich ore. This ore type does not recover well on the heap leach pad due to its refractory nature. Geometallurgy is vital for ore characterization for the two recovery methods. Geometallurgy helps develop indices that are used to predict parameters that influence overall recovery and production, such as hardness, crushability, grindability, pH fluctuations, gravity (coarse) gold, flotability and cyanidability. Using geology and mineralogy along with other analytical data, geometallurgical models are constructed and applied to the resource block model for proper planning and extraction of the gold. Geometallurgy aims to analyze the variability in the different responses to the parameters to help reduce risk (costs) and optimize recovery (profit).

Jan 1, 2013

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

By G. E. Erdman

This paper presents talc milling guided by a theme of "So You Want to Be In The Talc Business". Such a theme strikes a cautionary note to warn the uninitiated of potential pitfalls, and this paper will cover briefly some of the technical traps as well as one of the larger talc milling operations. It is important to our purpose to pre- sent some of the market and mineral complications that make the business of producing and selling industrial talcs much more intricate than an outsider would perceive. Metal markets by comparison are great worldwide pools into which production streams of generally identical metals can flow over a weir of market prices. Industrial talc markets are not as well defined and often must be developed by the producer working closely with a specific customer or groups of customers to prove out the attributes of the specific product from a new property. All the negatives of a new market seem to work against the introductory talc in the forms of industry or customer reluctance to change, sales prices, cost of delivery, mode of transportation, health considerations of the minerals and many more. Just locating the potential customers for a new industrial talc may be a substantial undertaking. Thus, an analogy of the worldwide metal market might compare starting a new talc operation to trying to gather up enough fallen rain drops to be able to start a production stream of a worthwhile size.

Jan 1, 1984