Search Documents

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By Aimee A. Woolsey

Enterprise unmanned traffic management (E-UTM) is a holistic system concept evolving from technological developments in radio frequency (RF), where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low in size, weight and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations, thus enabling mine management to have better decision-making capabilities in the current and future mosaic of mine operations.

May 1, 2023

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By M. K. Patel, K. C. Wade, M. Cross

In the past decade a good deal of effort has gone into the computer simulation of the heat distribution of pellet induration systems. The major uncertainty in the analysis of such systems is the gas flow distribution and, in particular, the role of leakage. Evaluation of the leakage into or out of a zone has proved to be very difficult, as has the cross-flow from one zone to another when adjoining zones have gas flows which change direction from up draft to down draft for example. This paper describes an initial model to calculate the gas flow distribution in a variety of practical situations of interest to those involved in pellet induration. The model is based upon a multiphase CFD code called CASCADE which is used in conjunction with the pellet induration simulation INDSYS.

Jan 1, 1990

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By P. J. Ryan

December 1988, Phelps Dodge Corp. brought an underground gold mine into production in the republic of Botswana. The mineralization is associated with steeply dipping shear zones in Archean greenstones of the Tati schist belt. The gold is intimately associated with sulfides and is refractory in nature. The deposit is being exploited by underhand open stoping methods. Vertical and inclined shafts are used to hoist the ore to the surface where it is treated by conventional crushing, milling, and flotation, followed by fluid bed roasting with cip elution and carbon regeneration. Adjacent deposits are being explored with a view to increasing production. Legal and taxation aspects of operating in Botswana are discussed.

Jan 1, 1991

By Trevor Riters

Advancements in Emerson’s instrumentation technology have brought value and efficiencies to the mining industry. Some think of instrumentation as basic sensors and valves, but with our solutions, we equip operators with real time, accurate, and reliable data that they can use to operate more effectively. Working with Caltrol, an Emerson Impact Partner, we successfully engineered wireless skids for a leach pad to provide precise measurement and control of raffinate solution to many of the large mine sites in Arizona.

Feb 1, 2025

By Russ Darr

New methods and techniques in the field of hydrogeology are being developed constantly. One of these advances has been brought about through the use of inexpensive microcomputers. The formulas used in this paper and developed by Theis, Jacob, Glover, Keck, and Dupuit are not new. The methods by which these formulas can be solved are now available to all who wish to get faster, less expensive, and more reliable answers. These methods involve the solution of standard groundwater formulas using microcomputers. Examples and case histories of these methods are presented

Jan 1, 1980

By ETHAN FUSTER, Richard Ray Jr, STEPHEN LEE

The abstract states that horizontally-mounted jet fans are commonly used to ventilate vehicular tunnels due to their space and cost savings compared to fully ducted systems. It highlights the successful use of vertically-mounted jet fans in exhaust ventilation shafts for a passenger rail overbuild in New York City. The paper compares shaft dimensions, jet fan placement, and measured airflows, also comparing these measurements to predictions from computational fluid dynamics (CFD) simulations.

Mar 16, 2022

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Muhammet Mustafa Kahraman

Despite technological advancements and organizational adjustments, lost time accidents are major issues in occupational safety. However, there is very limited work that focuses on variables influencing days lost as a result of occupational accidents. In this study, decision tree and artificial neural network methods were used as machine learning techniques to investigate the impact of factors on accident lost day duration. Degree of injury, worker age, and worker activity were found to be the top three variables impacting loss of time from work. It was also identified that the mining method, location, and nature of injury had a moderate influence on duration lost due to occupational accidents. However, worker experience and ore type did not have any significant impact on the duration, which is an unexpected result. These results confirmed that some accident factors that might have a large influence on the number of mine accidents can be less critical when it comes to accident lost day duration.

Feb 3, 2021

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By Bryan Ulrich

On March 15, 2012, about 24 attendees from several western states attended Roundtable 2012, hosted by Knight Piésold and Co. at the Red Lion Hotel and Casino in Elko, NV. The focus of this year?s discussion was ?Acid Rock Drainage for Engineers and Environmental Scientists.? Other names may have been more suitable for the event, perhaps combining geochemistry, with air and water quality and their long-term effects on soil and rock mechanics. Bryan Ulrich (senior vice president, Knight Piésold?s Nevada operations) and Steve Lange (senior geochemist, Knight Piésold, Denver, CO), helped facilitate the discussion. Attendees included personnel from a dozen mining properties, various corporate offices and academia. There were also attendees from a geochemical testing laboratory to help respond to specific questions pertaining to testing protocol and procedures.

Jan 1, 2012

By S. A. Pirzada

A thermal plasma assisted laminar flow reactor has been used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables include: alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1996