Search Documents

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By K. Ueda

Lead concentrates from Kuroko (black ore) mines, which contain Cu 4 ? 7%, Pb 55%, Zn 3 - 7%, As 0.5 - 0.9% are treated by hydrometallurgical process in order to smelt the product by electric furnace smelting together with other lead resouces from Kuroko. The hydrometallurgical pretreatment involves sulfuric acid leaching at first stage, ferric leaching at second stage. This paper describes the short history of lead recovery from Kuroko and the performance of laboratory test, pilot plant and commercial operation.

Jan 1, 1982

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By Lana Alagha, Keitumetse Cathrine Monyake

The abstract discusses the synthesis and investigation of polyacrylamide functionalized chitosan polymers (CS-PAMs) as selective depressants for pyrite in the flotation of galena and chalcopyrite from complex sulfide ore. The study employed response surface methodology (RSM) to model and optimize the flotation process, varying parameters like the degree of deacetylation of chitosan, weight ratio of chitosan to acrylamide, and CS-PAM dosage. The developed RSM models effectively predicted iron and lead grades and recoveries, while optimization showed optimal pyrite separation from galena and chalcopyrite using CS-PAM synthesized from chitosan with a high degree of deacetylation and a specific chitosan:acrylamide weight ratio.

Apr 9, 2022

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Nikhil Dhawan, Shrey Agrawal

India’s most extensive renewable energy expansion program targets 280 GW of solar energy by 2030. Due to the massive generation of photovoltaic waste (expected 34,600 T by 2030), stringent recycling effort to recover metal resources from endof- life PVs is required for resource recovery, circular economy, and subsequent reduction in the environmental impact. The present study investigates the recycling potential of end-of-life silicon solar modules. The feed characterization reveals that most of the values in PV modules are concentrated in the frame (pure Al), Si wafer (72–84% Si, 9–12% Al, and 0.13–0.71% Ag), and electrical connections (Cu wire coated with Sn). The Si and Ag values in the feed were beneficiated using water fluidization, and concentrate with 90% Si and 2% Ag was attained in the underflow concentrate. Ag values were recovered in the form of AgCl by leaching in nitric acid and precipitation. After the purification step, the residue containing 99% Si can be further utilized to fabricate Si wafer and Al-Si alloy. The preliminary cost estimations suggest that the proposed process is economically viable for the recycling of solar panels with the maximum value generated from the AgCl precipitate followed by Al panels and Si wafers.

Nov 14, 2022

By S. K. Kawatra, H. Haselhuhn

"In many mineral processing applications it is necessary to know the isoelectric points of the various minerals in the ore to properly perform flotation and other mineral separations. However, current zeta potential analysis technology used to determine the isoelectric point of a particle suspension cannot deliver the isoelectric point of each individual mineral, just an average of the mineral system. Traditionally, individual isoelectric points have been gathered by testing pure, synthetic minerals. These values can vary widely depending on the mineral synthesis procedure and the water quality used during the isoelectric point analysis. A more robust approach for determining the actual isoelectric point of a particular mineral in a mixture of minerals is needed. This paper details a method for determining the isoelectric point of an iron oxide mineral in a siliceous iron ore. The method uses a laser scattering particle size analyzer and a pH electrode to determine the pH at which the liberated mineral particles begin to flocculate as pH is decreased. The pH at which the average particle size rises dramatically is the isoelectric point of the mineral with the highest isoelectric point in the ore. This measurement technique was used on natural hematite, goethite and siderite ores as well as a synthetic mixture of pure silica and pure hematite. The results for synthetic hematite mixtures were comparable to literature values.IntroductionRecently there has been an increased interest in the processing of low-grade iron ores (Bolen, 2014; Carlson and Kawatra, 2008, 2011, 2013; Halt et al., 2014; Halt and Kawatra, 2014; Haselhuhn 2012, 2013; Haselhuhn et al., 2012a, 2012b; Kawatra and Halt, 2011; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). The zeta potential of iron ore minerals is a very important and often overlooked aspect of iron ore mineral processing. Zeta potential is the charge at the shear plane of a surface in an aqueous environment (Carlson and Kawatra, 2013). Many ores consist of a variety of minerals differing in zeta potential. This property of a particle surface in water is responsible for either keeping the particles dispersed from each other or flocculated to each other. This is important during many operations such as flotation, desliming and thickening. Zeta potential is primarily a function of the pH of the water and the mineralogy of the particles, though certain ions within the water can also have a significant impact (Haselhuhn, 2012). Consider the following situation: silica (SiO2) particles and hematite (Fe2O3) particles are suspended in an aqueous solution. These two types of minerals have drastically different zeta potentials throughout the pH spectrum (Esumi et al., 1988). In alkaline conditions, both types of particles exhibit negative zeta potentials and will tend to disperse from each other. In acidic conditions (between pH of 3 and 6), silica has a negative zeta potential while hematite has a positive zeta potential, so these surfaces will tend to be attractive to each other and the particles will flocculate and settle. This phenomenon is visually described in Fig. 1. The pH at which the two minerals begin to attract to each other, or destabilize, is near hematite’s isoelectric point. The isoelectric point is defined as the pH at which the surface has a net zero zeta potential (Carlson and Kawatra, 2013)."

Jan 1, 2015

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By Konrad J. Banaszak

At least for the time being, these seems to be general but not universal agreement that Mississippi Valley type ore deposits formed entirely or in major proportion from heated connate brines (e.g. 1) Even with that agreement, major questions remain. I will present a coherent geochemical model and look at alternative views in the context of that model. The pattern of the following discussion is 1) the general geochemistry of the ore fluid, 2) the density-temperature relations and possible mechanisms of flow of those fluids, 3) the mechanisms of transportation and deposition of the ore minerals, and 4) a summary of a coherent model of genesis. The data equivocally define much about the deposits. The answer is still elusive.

Jan 1, 1979

By W. H. Pailes, V. Castranova, K. Van Dyke, J. H. Kang

Recruitment and activation of phagocytic cells after inhalation of occupational dusts has been implicated in the development of pulmonary inflammation, fibrosis, or emphysema. Plateletactivating factor has been described recently as a potent inflammatory agent. The objective of the present study was to investigate if platelet-activating factor might play a role in the inflammatory response of the lung to occupational dusts. In vitro exposure of alveolar macrophages to cotton dust (4 mg/ml), silica (10 mg/ml), or coal dust (10 mg/ml) results in the release of picomole levels of platelet-activating factor with a potency of cotton dust > silica > coal dust. Time course studies indicate that platelet-activating factor release from alveolar macrophages is maximal approximately 10 minutes after in vitro exposure to silica. In vitro, platelet-activating factor is a direct stimulant of polymorphonuclear leukocytes increasing chemiluminescence 2.3 ± 0.3 fold above control. The maximal response occurs in the dose range of 10-10 to 10-7M platelet activating factor. In addition, plateletactivating factor potentiates the response of polymorphonuclear leukocytes to a second stimulant; i.e., chemiluminescence generated from polymorphonuclear leukocytes exposed to plateletactivating factor (10-9M) plus chemotactic peptide (FMLP, 10-9M) is 88 ± 22% greater than the sum of the separate effects of these stimulants. In contrast, platelet-activating factor is not a direct stimulant of alveolar macrophages in vitro, having no stimulatory effect on chemiluminescence or superoxide anion release even at levels of 10-6 to 10-5M platelet-activating factor. However, platelet-activating factor (10-5M) does potentiate zymosan-stimulated activation of chemiluminescence and superoxide release from alveolar macrophages by 117 ± 56% and 30 ± 4%, respectively. In conclusion, these data indicate that exposure of the lung to occupational dusts results in the release of platelet-activating factor which may activate polymorphonuclear leukocytes and potentiate the responsiveness of alveolar macrophages to dust. The net result would be pulmonary inflammation and hypersecretion of reactive species by pulmonary phagocytes which could lead to tissue damage and pulmonary disease.

Jan 1, 1991