Search Documents

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005

By I. Ocak

Initial investment for mechanical boring of tunnels is found to be high in most cases. Conventional drilling and blasting is not the possible especially in urban area. In these conditions impact hammer offers many advantages over conventional drill and blast techniques and boring tunnels. These include improved safety, minimal ground disturbances, elimination of blast vibration, reduced ventilation requirements, reduced cost etc. Therefore, hydraulic impact hammers have been used widely in metro tunnelling projects in Istanbul since 1992. Accumulated and published data from various tunnelling projects serve to improve predicting the machine performance and scheduling of job duration. This paper is prepared under this objective. Machine utilization time of impact hammer was evaluated in this study. The main rock formation named Kartal formation arepaleozoic aged sedimentary rocks, shale, sandstone, siltstone, andesite dykes and sediment fillings. The first stage of the project is commissioned to Yapi Merkezi- Yuksel- Dogus- Yenigun- Belen consortium.

Jan 1, 2011

By E. Z. Manos

The Detroit salt mine is operated by the Detroit Salt Co. It is one of the oldest underground room-and-pillar mines in the United States still in production. Mining at the Detroit salt mine began in 1906 with the sinking of the No. 1 shaft. Mining continued through the years, becoming progressively more modern in its equipment and techniques, until it was closed in 1983. In 1997, after a period of care and maintenance, the newly formed Detroit Salt Co. decided to reopen the mine. Upon completion of an extensive rehabilitation program, salt production resumed in 1998. Production currently continues at a rate of 910kt/a (1 million stpy). To date, the Detroit salt mine has mined more than 45 Mt (50 million st).This mine is unique because it lies under a heavily urbanized area within metropolitan Detroit. The mine and its history make a good case study for the continuing coexistence between the mining industry and its environs.

Jan 1, 2003

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By M. Wickham

Design of an open pit backfill requires an understanding of highly varied processes including slope stability, hydrogeology, pit lake chemistry, climate, runoff, and mine waste behavior. Dynamic systems modeling (DSM) provides flexibility to the designers of open pit backfill, allowing them to directly integrate many different physical processes and varying levels of complexity. DSM also provides for the efficient application of uncertainty analysis to define a range of possible results, the sensitivity of the results to uncertainties in model inputs, and the value of additional data. This paper presents the results of an analysis using DSM to evaluate a pit backfill design at an Arizona mine. The objective of the partial backfill was to stabilize an active slope that threatened facilities adjacent to the pit. DSM was used, in part, to develop a pit lake water balance model for evaluating the influence of the backfill on the ability of the pit to maintain passive hydraulic containment of groundwater and surface water inflows and for evaluating costs for various backfill scenarios.

Jan 1, 2001

By Edward H. Jr. Boyle, Paul R. Thomas

Introduction It is estimated that nearly 40% of all the gold ever mined in free world countries has been produced by South African operations. There is concern that this immense productive capacity will soon decline. Such a decline could reduce world gold supply and lessen the ability of market economy countries (MEC) to exert the major influence upon the world gold market. This paper addresses three general issues concerning South African gold production: • How much gold remains to be recovered from the demonstrated resources of the 44 evaluated South African mines; • How long can production at current levels continue; and • What will be its cost. Table 1 provides production data on the world's 10 largest producers for the years 1971, 1981, and 1983. As shown, South African gold production declined significantly from 1971 through 1981. As of 1981, annual South African gold production had dropped by more than 311 t (10 million oz) in 10 years. Despite this, its mines still produced 656 t (21 million oz) that year, about half the world total. From 1981 through 1983, this trend was reversed. Annual South African gold production increased by more than 21.8 t (700,000 oz). The trend reversal was also evident in the US, Canada, and Australia. This illustrates the general, inverse relationship between gold price and gold production. In South Africa especially, as gold prices increased substantially during the 1970s, the average grade of ore mined (pay limit) was lowered as new, lower grade areas and materials were exploited. Gold production declined in volume. But gold revenues increased, and the lives of the operations were extended. The 1981-83 period was one of declining (US dollar-based, average annual) gold prices that resulted in increasing South African production as average ore grades were raised. South Africa currently accounts for 50% of world production (Fig. 1). Figure 2 illustrates South Africa's contribution to total MEC production in 1971 and 1983. Although South Africa's relative share of production has declined, it still represents the single most important source of new gold supply. In 1983, it supplied more than 65% of total MEC production. South Africa currently produces more than twice as much gold as the Soviet Union (ranked second in world production), and 11 times more gold than the US (ranked fourth in world production). Barring major discoveries, South African gold production is expected to peak in 1987 and begin to decline again throughout the 1990s. The rate of decline is ex-

Jan 11, 1984

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By J. Wiese

Recently the operating philosophy at concentrators processing platinum bearing ores has started to move from a recovery dominated system to one in which the production of high grade concentrates at the expense of some recovery would provide greater benefits in the further upgrading of the platinum group minerals (PGM). The low grades usually obtained are associated with the presence of naturally floatable talcaceous gangue minerals in all PGM ores. Polysaccharide depressants such as guar gum and carboxymethyl cellulose (CMC) are used to improve the grades of the concentrates. Recent testwork has shown that the use of high depressant concentrations can prevent any naturally floatable gangue from reporting to the concentrate. The only gangue present in the concentrates would be due to its entrainment in the froth. Under these conditions much higher grades can be achieved. The sulphide minerals themselves, however, become susceptible to depression at high depressant concentrations. This work examines how the recovery of sulphide minerals in two Merensky ores was affected by the type and concentration of the collector in the presence of high depressant concentration (500 g/t) and that the response of the sulphide minerals was also dependent on the type of depressant used (guar or CMC).

Jan 1, 2009

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

Diesel Particulate Matter (DPM) issues are very high profile currently in both Australian coal and metal mines and Australian states are generally moving to acknowledge and to broadly follow US 2008 final metal/non metal mine regulation limits of 0.2 mg/m3 submicron particulate matter, 0.16 mg/m3 total carbon particulate and 0.1 mg/m3 elemental carbon particulate. The real time DPM monitor is being developed on the base of the successful Personal Dust Monitor (PDM) unit. The objectives of recently completed Australian Coal Association Research Program (ACARP) study has been to finalize the design of a DPM unit, to undertake comprehensive and internationally recognized laboratory testing to evaluate the new design and to undertake an underground series of tests to establish the robustness and reliability of the new approach. Under the project Thermo Fisher Scientific has undertaken structural changes to the PDM to convert it to a DPM real time monitoring underground instrument, the D-PDM. The Pennsylvania Pittsburgh Research Laboratories of NIOSH (the group that originally contracted for the PDM development) has undertaken laboratory ?calibration or verification? testing. A phase of Australian mine robustness and engineering testing has been undertaken to ensure the instrument can effectively assist mine management to handle this health issue. Tests have been undertaken at points of expected high atmospheric DPM such as during Longwall face moves, Development RAM car, Eimco and PJB usages. The paper discusses how the monitors have performed within the underground mine environment in evaluating DPM during the various phases of the production cycle. They have closely examined the influence of aspects of the mine ventilation system. Results have been compared to alternative industry pollutant measuring approaches. The outcome of the project gives the industry access to an enhanced tool for understanding the mine atmosphere in the presence of DPM. Real time DPM monitoring will allow the industry to pin-point high exposure zones such as those encountered in coal longwall face moves where various vehicles work or in areas of constrained or difficult ventilation. Identifying of high DPM concentration zones allows efficient modification of work practices to reduce underground miners? exposure. Some outcomes of the ACARP project in this area will be discussed.

Jan 1, 2009

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By K. Bounou, K. Komnitsas

"Risk quantification may be used as a sustainable development index in the mining industry, since it encompasses both economic and social factors. In addition, it may assist in the development of a framework, which is also indirectly related to sustainable development, to prevent accidents and improve health and safety standards. However, risk quantification in the mineral sector involves diverse activities and is considered a very difficult task. Although statistical data report accident severity rates, incident rates and accident frequency rates, none of these allow for accurate risk calculations. In this paper, two risk calculation formulas, which may be used to quantify risk, as well as to identify hazardous activities in a workplace, are proposed. Numerical examples are given based on statistical data available through the MSHA database. Also a combination of a decision/fault/event tree that allows risk quantification is presented."

Jan 1, 2005

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013