Search Documents

By P. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The feasibility of recovering cyanide and copper from a gold mill barren solution was evaluated in a small A VR pilot plant. The campaign lasted 64 hours, during which time about 4,000 L of gold mill barren solution were processed. The results showed that A VR is an effective technology for recovering cyanide and copper from barren solutions. Under the best conditions, the copper precipitation and the cyanide volatilization attained 94% and 98%, respectively. Using 5 MNaOH as the absorbent, practically all the HCN gas was recovered in the form of a concentrated NaCN solution containing 70 g/L free CN. Basic engineering design parameters applicable to a large-scale operation were obtained, including the Henry's Law constant and the mass transfer coefficient for HCN gas.

Jan 1, 1997

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low-and high-rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Jan 1, 1997

By R. A. Metz, Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity,' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1992

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971

By R. Pinksen

The IOC Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1.0 m x 1.0 m x 1.0 m; 39 inches x 39 inches x 39 inches) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduces the infiltration of the emulsion into the cracks and fissures of the rockmass. Reduced amounts of oversize and more consistent fragmentation throughout the muckpiles has been a result. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a of first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A Digital Vision System (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By R. L. Pearson

The 1987-88 Denver Brown Cloud Study was performed to determine the sources of the particle cloud which forms over Denver each winter. The study was organized under the leadership of Colorado Governor Roy Romer , EPA Region VIII and the Greater Denver Chamber of Commerce. The study was sponsored by over 40 organizations representing governmental agencies, the natural gas industry, the coal industry, utilities, oil companies, railroads, the motor vehicle industry, and other Denver area companies and organizations. The cost of the study was $1.5 million which was raised almost entirely from private sources. The study team was headed by Dr. John Watson of the Desert Research Institute of the University of Nevada. Dr. Watson is a recognized expert in conducting studies of this type.

Jan 1, 1990

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By C. I. Basilio

Pearson's hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago's theory and flow micro-calorimetry.

Jan 1, 1991

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982