Search Documents

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022

By A. J. S. Spearing, A. Mueller

The support of intersections in coal mines remains an important safety issue, mainly because the large diagonal span compromises the stability of the roof. This structural weakness is further exacerbated if the intersection is developed incorrectly, the pillar corners fail or the crosscuts are angled (not perpendicular). This report details the current support systems used and investigates unplanned falls of ground in intersections in coal mines throughout the United States. A possible failure mechanism is proposed and some suggestions are made to improve the effectiveness of the support in these vital areas.

Jan 1, 2009

By Mads Aniksdal

New Nedre Fiskumfoss is a construction project in North Trøndelag, Namsen River. The purpose of the contract is construction of a new hydropower plant, that will phase out the existing power plant in the same waterfall. The contract consists of a tunnel system with cross sections from 16 m2 to 150 m2, powerhouse and transformer in rock caverns, 6 shafts and major works with inlet and outlet below river level. Technical challenges consist of demanding design on rock extraction, cofferdams, solid constructions with challenging design and demanding rebar work, as well as restrictions and unpredictable water flow in a national salmon river.

Jun 13, 2023

By L. C. Morales

During my College days in Mexico City, my Mineralogy Professor used to say "Mexico is the Horn of Plenty, rich in minerals, and it is easier to say which minerals are not found instead of stating all that exist. He said that the only ones missing are bauxite, diamonds and titanium ores." Today, twenty years later, a rutile mine in Oaxaca is in successful operation. Mexico has an area of approximately two million square kilometers, with volcanic activity, large shores and mountainous areas reaching as high as 6,000 meters above sea level. These conditions are favourable for most mineral deposits, some -of commercial value and others as a source of mineral samples only. (fig. No.1) In addition to vast mineral wealth, Mexico has -another valuable asset in .his people. Even before the discovery of America, natives were successfully mining metals, and during the Colonial --days, the mineral deposits were mined to increase the wealth of Spain, and it increased the --knowledge of mining. All this experience was passed along from generation to generation, and created a tradition of mining and minerals processing engineers, that currently account for approximately 182,000 persons supported by mining related activities.

Jan 1, 1994

By Ronney Rodrigues Silva, Renata Mendonca, Gabi Knesel, Cathrine Monyake

Locus Mining is working side-by-side with a prestigious iron ore company to evaluate the addition of Locus ESG-friendly green flotation reagents with the primary goal of improving recovery and grade. In this paper, we will focus on the cationic reverse flotation application. The most “established industry” reagents for cationic reverse flotation are amine as the collector, starch as the depressant, and in some cases frothers are also used (among them MIBC, pine oil, others). Here, we evaluate the synergies of different classes of eco-friendly biosurfactants and industry-standard reagents during the cationic reverse flotation method. Exploratory research was done first with an analog sample under different pHs, eight different biosurfactants with starch and no-starch, and a customized DOE was used to perform 145 microflotation tests. The results show Separation Efficiency from 20% (baseline) to 50% (biosurfactant), and Selectivity from 3.27 (baseline) to 5.67 (biosurfactant). Optimized result conditions were then applied to the iron ore samples received from our client to perform flotation tests on a Denver Lab cell. Similar results were obtained by improving Separation Efficiency and Selectivity, which corroborate with the previous work.

Feb 1, 2025

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By J. F. Childs

Montana consists of an Archean crystalline basement overlain by Proterozoic through Cenozoic sedimentary rocks. Igneous rocks range in age from Archean to Pleistocene; the most voluminous magmatism and volcanism occurred during the Late Cretaceous and early Tertiary. The state can be divided into three tectonic provinces whose deformational styles are a function of different bedrock responses to Late Cretaceous-early Eocene compressional tectonism. Several long-lived structural zones have been periodically reactivated since the Precambrian, and were the sites of recurrent magmatism. Regional gold distributions are strongly influenced by the tectonic provinces and structural zones. Lode gold systems in Montana occur in diverse geologic settings resulting from a complex interaction between structure, magmatism, and sedimentary depositional processes. Reserves or resources are known for 19 significant lode gold systems, and additional unannounced discoveries have been made recently. Mineralization ranges in age from Archean to Tertiary. The influence of long-lived structures is apparent at both the regional and deposit scale, and in some cases multiple mineralizing events have been superimposed upon one another. Most Montana gold systems have a direct spatial and genetic association with Late Cretaceous through Oligocene igneous rocks. However, the importance of sedimentary rocks and associated depositional processes should not be underestimated.

Jan 1, 1993

By D?Arcy R. George

A survey of the copper mining industry in Western United States revealed that uranium is almost universally present in the solutions resulting from leaching the waste ore dumps to recover copper. The U308 content ranges from about 2 to 15 ppm and a potential production of up to 1,000 tons of U3O8 per year is indicated. A six-week pilot plant test at the Bingham Canyon mine of Kennecott Copper Corporation showed that the uranium is readily recoverable by ion exchange techniques. The design of the new types of countercurrent ion exchange columns and operation of the pilot plant are described.

Jan 1, 1967

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T '1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, some 240 mines were registered in New Mexico, including 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production of potash, perlite, zeolite, and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. New Mexico has potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REE), and zircon. Other REE deposits are being explored. REE-Th-U veins are found in the Gallinas, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Recent exploration has occurred for beryllium in the San Mateo Mountains, Iron Mountain, and Victorio districts. Companies also are examining High-Ca limestone and High-Mg dolomite for potential development. Aggregate continues to be important in urban areas and along highways. INTRODUCTION Industrial minerals and rocks are literally the building blocks of our way of life and they are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure, and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics and refractories to paper. Although industrial minerals permeate every aspect of daily life, their presence and their role are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a by-product of cleaning natural gas, one of the world's major energy fuels. Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 40% of the more than $2.8 billion generated by mineral production in New Mexico in 2013 (Table 1, see APPENDIX). In 2015, some 240 mines were registered in New Mexico. This total includes 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production in potash, perlite, zeolite, and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. Additional production statistics are in Harben et al. (2008). Major industrial mineral districts are shown in Figure 1."

Jan 1, 2016

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 800-6,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phase vertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well as volumetric flow rates were measured by electromagnetic (EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 104 < Re < 105 show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991