Search Documents

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than four percent P205 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low grade feed In sea water required that the conventioinal Crago Process, comprising direct anionic flotation, deolling, and inverse cationic flotation be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1986

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

By Yuting Xue, Mark Van Dyke, Joe Wickline

The understanding of coal mine roof lithology is a critical component in the determination of engineering solutions for roof control. Coreholes were the first technology available to determine lithology of the roof in reserve areas, but coreholes are typically drilled 500–2,500 ft apart due to their cost and sometimes reach more than $125,000 dollars per hole, depending on mine conditions. The next method developed to bridge this gap was the fiber-optic scope which is utilized in the roof at the faces of underground development. High-end fiber-optic scopes can also be costly (20,000–40,000 dollars) but are more affordable than drilling a corehole, and the information can be processed immediately to make quick roof support determinations. The fiberscope can be operated wherever a roof bolter can drill a hole, and there are no restrictions related to property owners, proximity to streams, elevation changes, etc. The latest borescoping method utilized by mining companies is the use of videoscopes. Videoscopes and all borescopes in general are limited by the lengths of the scope and the length of the borehole drilled in the mine. Videoscopes have the advantage of being able to record video while examining the roof lithology. The information can be recorded quickly underground and then be examined on the surface which allows anyone to capture the video so that a geologist can make lithology descriptions without ever going underground. In the past, videoscopes had limited resolution, a short battery life, were fragile and were relatively costly. As technology progresses, videoscopes have become more affordable, have increased battery life, and offer enhanced 1080p resolution. With the broader availability of affordable videoscopes, videoscopes can be more readily used in various mine environments at every active section underground. This paper will discuss the types of videoscopes available, the features that will aid in lithology description/identification, the deployment methods pertaining to supplemental roof support recommendations, and an advanced methodology to enhance accuracy in understanding roof lithology.

Feb 1, 2025

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By B. Seegmiller, W. A. Hustrulid, O. Stephansson

Introduction The concept of in-the-wall haulage was formally introduced to the mining community in the early 1970s. The basic concept is simple. Rather than the traditional in-the-pit haulage/access ramp, single or twin ramps driven in the pit wall are used with crosscut connections on the working levels. The in-the-wall pit haulage system could be considered as part of the opening of a new mine, a way of completing to final depth an existing pit, or part of the transition from open-pit to underground mining with the ramp remaining as part of the access. This paper is intended to acquaint the reader, particularly mine planning engineers, with some of the possibilities presented by the concept. Nordstrom (1983) said, "In many countries, mining engineers are either open-pit or underground specialists and, hence, often don't consider the possibilities for combining the best aspects of each into a hybrid mining system." This is believed to be true. There are few "hybrid mines" employing, for example, open-pit methods with underground haulage systems. One reason is the variance with the experience of the mining company and the engineers involved. However, with today's low metal prices, innovative and unconventional thinking may be just what a property requires to remain in production. All the possible situations where an in-the-wall ramp might be considered cannot be presented here. Rather, a few examples will be discussed for illustration purposes. Potential savings in stripping costs A major cost in open-pit mining is associated with the removal of overburden and waste rock. Although much of this stripping cannot be avoided, the volume (V) associated with the presence of an in-pit haul road can be quite large, V 100 (pit depth) a (road width) 2 x road grade (%) As an example, consider a vertical ore body 400 m (1312 ft) long, 60 m (197 ft) thick, extending to a depth of 160 m (525 ft). Cross sections are shown in Fig. 1. Other data are: ore tonnage = 11 Mt (12 million st), ore density = 2.9 t/m3 (0.09 st per cu ft), waste rock density = 2.7 t/m3 (0.08 st per cu ft), road width = 20 m (66 ft), road gradient = 10%, and level interval = 10 m (33 ft). The evaluation has been made assuming that the pit slope (0) is constant around the pit except on the side with the haul road. On this side, the slope is decreased to allow for the road. Slope angles of 30° to 60° have been selected to indicate the dependence of stripping volume (V) on slope angle. The stripping at the ends have been calculated assuming representation by cones. The volume associated with the haul road is 2.6 Mm3 (92.8 million cu ft). A comparison of the strip volumes involved is shown in Table 1. As can be seen, the percent savings in strip volume varies from about 4% to 17% and depends greatly on the slope angle. It is perhaps more interesting to examine the savings in stripping costs that could then be used to cover the cost of the access ramp and the crosscuts for stripping costs of $3/m3 ($0.08 per cu ft). The cost with the road volume is 2.6 million x 3 = $7.8 million.

Jan 1, 1988

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By W. J. Nosek

Reserve Mining Company completed construction on a major process modification project in June of 1980. These modifications enabled Reserve to reduce and control its final iron ore pellet silica content from 9.0 20.77 percent to 5.0 50.26 percent. The paper outlines the implementation of neutron activation on-line analysis and associated computer control loops for measuring and closely controlling the silica content of the iron ore concentrate at Reserve Mining Company. It contains a general overview of Reserve's taconite processing facilities and a presentation of the theory and operation of the neutron activation analysis equipment coupled with the computer silica control loops.

Jan 1, 1983

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By S. J. Lefond

Most people, when Borates are mentioned, mentally visualize the famous twenty mule team (really eighteen mules and two horses), trudging across the Mojave Desert or "she burns green Rosie, we are rich." Actually, however, the first use of borax was prior to Babylonian times. Their emissaries had orders to bring borax Iron the Gobi desert for use as a flux by the Babylonian goldsmiths. The borate mineral imported for this is not known but probably was borax. The ancient Persians and Arabians knew about borax and the Arabic word "Baurach" appears in a two thousand year old manuscript. The Sanscrit word for borax was tincana which has been corrupted to tincal. The Chinese were using borax as a glaze in three-hundred B.C. Marco Polo brought the first borax, along with gunpowder and spaghetti, from Mongolia to Europe in the late 1300's. Borax from Tibet was imported to Europe for nearly 500 years. In 1772 boric acid (sassolite) was discovered around Tuscany, Italy as a precipitant from volcanic steam vents. Production of boric acid started there about 1815 and provided the sole competition to the borax from Tibet. Borate deposits in Turkey have been known and exploited on a small scale since the 13th century. It is only recently that the operations are being modernized and production increased. About 1836, borax minerals were found in Chile and Argentina with borax production starting in 1852 in Chile and in Argentina in 1886. During the latter half of the 19th Century, Chile was the principle world producer of borax.

Jan 1, 1980

By Xinyang Wang

It is believed that sulfur and volatile matter contents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal - three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982