Search Documents

By Elimame Elaloui, Kais Elghniji, Constantin Virlan, Aurel Pui, Chaima Ouled Amor

Separation and identification of minerals composing the Tunisian silica sands have been conducted by acid etching and hot filtration/sedimentation (HFS) without affecting the quartz component. It was found that the hot acid etching process is an effective method to separate quartz and clay minerals in the silica sand. The SEM micrographs of the silica sand show rough surface and some cracks with irregular shapes. The surface becomes clean and smooth after acid etching process. After chemical dissolution, the clay minerals were recovered by hot filtration following by sedimentation at low temperature. FT-IR, EDS maps, and secondary electron (SE) analyses of separated clay minerals reveal the presence of Fe2O3, montmorillonite, and kaolinite minerals. The LIBS analysis of clay minerals shows the presence of Al, Fe, Ca, Al, and Mg. The sequential etching process can be introduced in the purification methods as an effective way to separate quartz from clay minerals.

Jul 29, 2020

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

During the past 20 years, FKC-Lake Shore, located in southern Indiana, has been working with Contitech, the German conveyor company, to push vertical conveyor technology to new depths and open up additional opportunities for underground mine owners. Historically, the underground mining industry has largely been unable to realize the benefits of these efficient systems due to the design limitations in maximum depth and capacity. Until recently, only relatively shallow depth mines with low production rates have been a ?t for a vertical conveyor system. This, however, is changing with technical advancements in the Pocketlift system. With each milestone, a new vertical conveyor record is set for depth and capacity. For instance, in 2002, FKC-Lake Shore set one such record with the installation of a Pocketlift system at a mine in the Illinois coal basin with a lift height of 273 m (896 ft) and a production rate of 1.8 kt/h (2,000 stph). Although it was unthinkable at that time, today?s vertical conveyors are capable of reaching lift heights up to 700 m (2,300 ft) with an average production rate of 450 t/h (500 stph). These new lift heights and production rates are opening the technology to more potential mine owners and shifting the way people look at moving material in the future.

By James O. Glanville

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal, prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. The literature relating to this process has been reviewed as has the literature relating to the chemical treatment of coal and mineral particulates. Some important articles are discussed and speculations are made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1980

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017

By Walter B. Hester

All persons and communities that have experienced strong-motion earthquakes are convinced of the importance and complexity of earthquake problems thatmust be solved in order to reduce the personal hazards and property losses to a reasonable minimum. It is also clear that absolute elimination of all risks is impossible. Reduction of existing hazards and precautionary measures which will minimize chances for disaster can be accomplished by realistic appraisal of the effects of recent earth- quakes on modern structures and installations. Localities that have reason to expect so-called strong- motion earthquakes can anticipate these effects by taking appropriate steps. Valid earthquake information can only be obtained from earthquakes. Each earthquake contributes to the body of knowledge by additional facts and by clarification of previous observations. Rational interpretation of the data followed by practical application of the conclusions can contribute greatly to the safety of persons and property. The general public expects the architectural and engineering profession to accept this obligation and render this service. Most earthquake hazards are man-made and arise from the imperfections of the works of man and his failure to anticipate the consequences when the natural characteristics of his environment are ignored. If it is not given to man to prevent such natural phenomena as earthquakes, it is sometimes within his power to control their destructive effects and to reduce to a minimum the toll of life and human suffering.

Jan 1, 1958

By Kevin Lofftus

The rest potentials of molybdenite electrodes are measured as a function of pH in absence and presence of flotation reagents. The chemicals used include sodium ethyl xanthate, kerosene, dextrin,sodium hydrosulfide, hydrated sodium molybdate, sodium sulfate, and hydrated sodium thiosulfate. The effect of dissolved oxygen is also noted. The obtained data are correlated with the results of micro-flotation tests obtained under similar chemical conditions.

Jan 1, 1984

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By H. EI-shall

Bench top centrifuge is used to study the consolidation behavior of phosphatic clays. A mathematical model (based on first order kinetics) is developed to describe the relationship between the void ratio (at any time) and the effective stress. Permeability of the sediment as a function of the void ratio is also described. The obtained data are compared with that obtained by other consolidation testing methods. Centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1995

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022