Search Documents

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By Wendy M. Brunner

A 70% excess of mesothelioma, an asbestos-related cancer, has been reported among men in northeastern Minnesota, where iron mining has been the major industry. The Minnesota Department of Health has studied iron miners who developed mesothelioma to identify possible sources of asbestos exposure. A database of all Minnesota residents diagnosed with mesothelioma between 1988 and 1996 was linked to a database of approximately 72,000 current and former Minnesota iron-mining employees to identify cases who had ever worked in the mining industry. The job histories of the cases were examined to determine if any of their jobs could have involved exposure to commercial asbestos. Seventeen individuals diagnosed with mesothelioma in Minnesota between 1988 and 1996 were found to have worked in the iron mining industry. Of the 15 for whom adequate work histories were available, 14 had identifiable sources of exposure to commercial asbestos in jobs held both inside and outside of the mining industry. The time between employment in these asbestosexposed occupations and the diagnosis of mesothelioma is consistent with the 20 or more year latency period that has been observed in other studies of this cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Asbestos; Iron miners; Taconite; Epidemiology; Case series

Jan 1, 2007

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By A. Koski

A pond rehabilitation and environmental education project were proposed by Cleveland-Cliffs Michigan Operations (CCMO) and approved by the Michigan Department of Environmental Quality (MDEQ) and the United States Environmental Protection Agency (USEPA) as partial fulfillment of conditions for a stream mitigation permit. The goals of the project were the rehabilitation of a pond on a tributary of a local trout stream, enhancement of public access and appreciation, and the initiation of a site-based environmental educational curriculum. Cleveland-Cliffs undertook a suite of actions to rehabilitate a pond created by a previous mining operation in 1912 and make accessible to local schools the aquatic and riparian ecosystems. Cleveland-Cliffs partnered with the local governmental unit and two local school districts. The rehabilitated pond and riparian zone provide an accessible natural area that local residents can use for such activities as hiking, biking, walking, fishing and nature study. Vegetative enhancement includes the planting of native shrubs, wildflowers and showy herbaceous plants in the pond, on the riparian fringe and the surrounding area. An interpretive trail was developed around the pond with signs created by a local master watercolor artist. Local schools built and installed picnic tables, benches and a kiosk. Cleveland-Cliffs created pond lesson plans tied to the Michigan Curriculum Framework, developed inexpensive teaching kits and hosted a workshop for teachers from nine local schools. Classes regularly utilize the pond during the school year conducting environmental studies. Nesting boxes, wildflower gardens, bat houses, frog deformity surveys and water quality studies are a few of the activities that classes have conducted at the pond.

Jan 1, 2007

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

By David M. Spatz

The way people interact, collaborate, learn and improve can have a profound impact on a company’s efficiency, performance, productivity and return on investment. This is the motive behind corporate efforts today to replace the traditional hierarchical structure with team-oriented organization. The increased importance of communication and collaboration during the past 20 years has been propelled by rapid advances in technology and increased availability of information. Companies must take advantage of the information that is required for competitive performance and for the continued production of quality products. So it is essential that outstanding communication, cooperation and collaboration take place among multidisciplinary specialists assigned to work together to solve common problems and achieve common goals. Companies are searching for ways to increase knowledge transfer and learning, particularly among people who work on related topics. This will improve efficiency and quality and reduce redundancy and costs.

Jan 1, 2000

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By Alfred Weiss

Selecting a minicomputer is not unlike selecting a costly piece of mining equipment such as a truck, shovel, crusher, or conveyor belt system. A marked difference might lie in the frequency at which such selection takes place; another difference might be mine management's familiarity with mining equipment vis a vis a minicomputer. These basic differences might prompt a mining company to seek the aid of a consultant when selecting a minicomputer system. Advantages and Disadvantages The fundamental advantage of employing an independent consultant is that it provides management with a source of knowledge and breadth of experience not readily available within the organization. If the consultant has a minerals background, such knowledge and experience are further enhanced by actual experience in exploration, mining, and mineral processing. If the consultant has worked within a mining company, such hands-on experience is supplemented with a meaningful understanding of the client's business; this facilitates communication between the consultant and members of the client organization. The consultant has been, so to speak, "in the client's shoes." There are several other advantages. Since computer systems cut across organizational boundaries, the independent consultant may be able to move within the organization more easily than an inside staff person to collect necessary information. Also, detachment from any manufacturer should provide the client with an objectivity and a set of recommendations as near optimal as feasible. The principal disadvantages lie in the area of continuity and accountability. Once the consultant's report has been submitted and his recommendations implemented, a discontinuity might occur. Also, if implementation does not provide the desired results, the consultant might not be available to correct the situation or account for actions taken. Proper selection of consultant services, relative to kind and duration, and the consultant's method of operation, will often prevent many of these aftereffects. Services Offered The professional consultant can help a client: •Define and summarize information systems technology* needs; • Evaluate alternatives such as in-house capability and capacity, time-sharing, or service bureaus; • Prepare a formal request for proposal (RFP) to be submitted to vendors; •Evaluate vendor proposals; •Evaluate the economics of lease vs. purchase; and •Assist in the conversion and installation. Thus, consulting services may range from evaluating an existing system and upgrading to a larger piece of equipment, to selecting a new first-for-the-organization computer. First, Define and Summarize Needs Regardless of circumstances, the most valuable document required before equipment selection is the information system plan (I/S plan). It helps insure that the company's information needs are met in a cost-effective manner. An I/S plan is usually a comporient of the mining company's overall business goals. Since an I/S plan is a formal vehicle for establishing and communicating the direction the organization intends to take to satisfy information requirements needed to achieve goals and objectives, most initial systems services are likely to center around creating such a document or updating an existing document. The trend toward company-wide I/S planning is increasing in the mining industry; however, smaller scale efforts focused at the information systems needs to support an individual

Jan 11, 1981

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By William R. Bond, Jim V. Rouse

Introduction The pressure/vacuum (p/v) lysimeter or soil water sampler has become useful for monitoring vadose zone or unsaturated zone water conditions. The soil water sampler was first introduced around 1961. It was used as a monitoring and research device for studies in agriculture and soil contamination around landfills. Since then, it has been used for many purposes. The use of p/v lysimeters at mining facilities to monitor for solution loss is a relatively new idea. The primary purpose of the lysimeter here is to function as an early warning system. It detects leakage through liners of tailings ponds, heap leach pads, and leachate holding ponds. Their use has proven valuable for collecting baseline data and detecting loss of precious leachate fluid. Different lysimeter designs are capable of vadose moisture sampling from near the surface and down to 90 m (300 ft). They are also capable of sampling soil moisture or saturation plume contaminants from areas not accessible by conventional water well installations. The most common installations are usually simple and cost-effective. In many cases, they can be installed without the use of heavy drilling equipment. A properly placed and installed lysimeter can detect solution leaks in several days or weeks. A conventional perimeter monitor well may take months or years to detect a leak of the same magnitude. A discussion on the general design and installation of p/v lysimeters will give an understanding of its versatility. Three case studies of lysimeter installations at mining sites will be examined in detail. Design, Installation, and Sampling Design The basic design of a p/v lysimeter chamber consists of a porous material through which the soil is drawn into a collection chamber. Access tubes run from the unit to the sample station at the ground surface. Most units currently available range from 25 to 76 mm-diam (1 to 3 in.-diam). The sample collection chamber, or body, can vary from 0.6 to 1.8 m (2 to 6 ft) in length. The body can be constructed of PVC casing or Teflon, depending on the installation desired. The collection chamber functions as a holding reservoir for the collected soil moisture. The intake, or porous material, on the lysimeter is the most complex and vulnerable portion of the unit. The pore size selection varies based on the needs of the installation, type of fluid to be sampled, and type of soil material surrounding the unit. Teflon (PTFE) and porous ceramic are used in fabrication of the porous inlet portion. When using a Teflon material, which is hydrophobic, a larger pore size of 70 µm is needed to overcome surface tension and draw water into the collection chamber. It is typically used at sites involving organic contamination, because of its inert properties. Ceramic material is generally hydrophilic, having less surface tension. Therefore, it has a smaller porosity range to conduct the moisture through the porous medium while under vacuum. Pore sizes may be selected from 0.16 to 6 µm, and can be manufactured for the specific needs of the installation. The final major design component of the p/v lysimeter is the access or sampling tubes. The tubes are usually of 6.3-mm-outside-diam. (0.25-in.-outside-diam). They are made of rigid polyethylene or flexible Tygon with a wall thickness of 1.5 mm (0.06 in.). The con-

Jan 4, 1985

By Jai-Woon Moon, Wonnyon Kim

Deep-sea hydrothermal vents (hereafter chimneys) are commonly found on the new crust forming along divergent plate boundaries. Related to the chimney cycle from birth to death, it is hard to define the growth stage of the chimney due to a brief life span of the venting hydrothermal plume. Here we try to categorize the mineral magnetic properties of the chimneys according to their venting fluid-temperatures. Hydrothermal sulfide deposits in the Southwest Pacific were explored in 2012 and chimneys were collected using remotely operated vehicle (ROV) and Grab with AV camera (GTV). In the present study, mineral magnetic properties of three Cu-rich chimneys were measured: a high-temperature chimney showing a venting fluid-temperature of about 200°C (ROV01); a lowtemperature chimney of about 80°C (GTV01); and an inactive chimney (ROV02). The chimneys were sliced to ~1 cm intervals from core to outer margin. Magnetic properties of ROV01 are dominated by pyrrhotite, except for the most outer part that experienced severe oxidation. Concentration and grain-size of pyrrhotite are relatively low and fine respectively. In the GTV01, pyrrhotite, dominant in the core, is gradually mixed with hematite toward the outer margin of the chimney due to secondary oxidation. Both the concentration and grain-size of the magnetic minerals are greater compared to the GTV01. High concentration and large grain-size of magnetic minerals characterize ROV02. Dominant magnetic phases are pyrrhotite, hematite, and goethite. In particular, the most outer margin shows the presence of magnetite produced possibly by magnetotactic bacterial activity. Such distinctive contrast in magnetic concentration, grain-size, and mineralogy among three different types of chimneys enables the life stage of the Cu-rich chimneys to be determined through a mineral magnetic study.

Sep 1, 2014

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007