Search Documents

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

The reality of rising electrical power costs and the haunting prospect of decreasing electrical power availability are a threat to the growth of new projects and expansion programmes that could negatively affect the sustainability of mining operations. These threats require the adoption of effective power saving measures aimed at three principal objectives: the elimination of wastage, the reduction of power usage particularly during peak demand periods and, more importantly, improving the efficiency of high power-demand processes. It is reasonable to assume that the greatest impact will be achieved by concentrating on those processes that are large electrical power consumers. For Anglo Platinum operations, mine ventilation and, currently to a lesser extent, mine cooling are two continuous processes that fall in this category. It is estimated that these may consume fifteen to thirty-five per cent of the power delivered to the shaft head-depending on the shaft's design. Mine ventilation systems suffer from inherent, historical inefficiencies that lead to excessive power consumption. Air cooling systems are designed to be energy-wise in terms of modulating refrigeration plant operation to meet the underground requirements while maximizing use of 'free' cooling from surface conditions. Currently about ninety-five per cent of the refrigeration capacity used in Anglo Platinum mines is dedicated to surface bulk air coolers. The net thermal efficiency of these systems is compromised as mines expand in depth and on strike. Looking to the future, this practice will be complemented by more energy demanding underground cooling tactics requiring considerably higher electrical power consumption per unit ton produced. To counter this increase in power consumption, more energy-efficient systems and advantageous transient strategies such as thermal storage and the use of ice-on surface and possibly even underground-are being considered. This paper describes work currently undertaken and planned by Anglo Platinum operations to reduce power consumption by main fans during off-shift periods, the associated efforts currently introduced to reduce underground air leakage, the possibility of introducing more efficient auxiliary ventilation systems, the feasibility of thermal storage, and a brief look at energy recovery system as a means of countering the anticipated power demand associated with underground cooling. Keywords Mine ventilation, mine air cooling, energy efficiency, chilled service water, energy recovery, air wastage, fan selection.

Jan 1, 2011

By P. S. G. Leon

One of the most difficult areas in concession contracts in resource-rich developing countries is achieving an equitable balance between the interests of investors, host states and, increasingly, mine and near mine communities. While some countries in the Andean region have resorted to outright or creeping expropriation of natural resource contracts under the guise of resource nationalism, others such as the Democratic Republic of the Congo (DRC), have claimed international best practice in the review (and setting aside) of important concession contracts.

Jan 1, 2011

By N. M. Skarbøvig

Safety nets have been used selectively in several South African mines over the years. Recently, however, an increased emphasis on mine safety has seen a resurgence of their utilization underground. This renewed interest has, however, also raised questions about the design and performance of these nets and their practical applications underground; these are the subjects of this paper. Generally, mine safety nets are used to protect personnel from falling rock in temporarily supported development ends, tunnels, ASGs and stopes. These diverse applications each require specific net designs, resulting in a wide product range. As a rule, however, mine safety nets need to carry specified static or dynamic loads with the least possible deformation. Because of the application-specific characteristics of mine safety nets, there is no South African national standard for them. Consequently, neither the SABS, nor the CSIR, performs standard tests on these components. In 2007, therefore, SIMRAC made available their Savuka facility for the testing of mine safety nets; the Savuka drop test became the accepted industry test standard for mine safety nets. From late 2007 to mid 2009, Norsenet, in collaboration with SRK Consulting, the designated operators of the site, conducted approximately 200 tests, which formed the core of Norsenet's database of safety net performance under various loading conditions. The test specimens comprised a wide range of net materials and config¬urations; the materials included: high density polyethylene, polypropylene, polyester, nylon, as well as a blend of polyester and polypropylene used primarily for reinforcement ropes. Net configurations encompassed the following parameters: net type, i.e., knotted nets or sewn nets; net strand type, i.e., braids, twines, or webbing; strand size; mesh size; mesh orientation, i.e., parallel or oblique to the net edge; net edge reinforcement, i.e., knotted, tied, with or without reinforcement ropes; internal reinforcement ropes, i.e., diagonal ropes and/or orthogonal ropes; as well as net attachment options, including loops and chainlinks. From the number of variables listed above, and the limited number of tests available, it can be appreciated that the findings of the test series required careful scrutiny. Nevertheless, principal performance factors clearly emerged: besides the obvious net mesh variables, such as net strand material, strand diameter and mesh size, it was the configuration of the reinforcement ropes and their attachment to the net panel which had the strongest influence on net performance. All the structural elements of a safety net need to work together to transfer the imposed load from the net panel, through the reinforcement ropes, to the net attachment points. In this load transference chain, the weakest link limits the strength of the structure. From this development work, Norsenet has gained valuable expertise to custom-design and manufacture nets to clients' specifications. The examples presented in the paper will also show the experience acquired in the installation of nets underground. Future work will include the establishment of a state-of-the-art net testing facility at Norsenet's factory in Vredenburg.. Keywords Mine safety net, safety net, protective device, mine safety, safety net design, safety net performance, safety net applications.

Jan 1, 2011

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By R. G. Votteler, A. C. Brent

"The business performance of mining corporations in South Africa is adversely affected by the constantly increasing electricity costs. The most commonly used power sources are the national utility supplier via a grid connection, and on-site diesel generators. Previous research has identified the renewable sources of solar photovoltaic (PV), onshore wind, and geothermal energy in hybrid versions with current sources as possible opportunities to counteract rising electricity costs. To provide a clear understanding of the new, developing market of renewable energy sources, this research is divided into two papers. This first paper investigates the internal business structure of mining corporations in order to evaluate electricity generating sources. The multi-criteria decision analysis (MCDA) method is selected as the most suitable approach for this. The paper identifies the criteria used by mining corporations to evaluate possible electricity generation sources for self-generation by means of the corporations’ own investment. Four mining corporations with several mining locations were interviewed. The interviews revealed both new and identical evaluation criteria when the findings were compared to earlier MCDA adaptations analysed in the literature review. The second paper (Part 2) combines current knowledge about the external macroeconomic environment with the findings about the internal environment described here. MCDA is adapted in Part 2 and implemented to analyse and compare current to hybrid renewable sources from the perspective of mines. IntroductionMining corporations in South Africa are currently adversely affected by increasing electricity prices. Electricity is supplied mainly by Eskom1 and, especially in remote locations, by on-site diesel generators (Boyse et al., 2014). Electricity price increases, emanating from diesel price hikes and Eskom, have escalated the total operational expenditure on electricity by the largest mining corporations from 8% to 20% of total operating costs in the past seven years (EIUG, 2015). The reliability of electricity supplied by Eskom has decreased drastically (Govender, 2008), and the prices will increase annually by at least 13% until 2018 (Numbi et al., 2014; Eskom, 2015b). In addition, the South African government plans to introduce a carbon tax on greenhouse gas emissions (Alton et al., 2014)."

Jan 1, 2017

By M. Kahn

This paper traces the rise of South Africa's mining industry in the context of the different state forms that oversaw its development. It commences with the mining-led industrial revolution through four periods of conflict, each of which contributed to a deepening of the industrial base, with constant battles between domestic and foreign capital and labour, and the rise of both Afrikaner and African nationalism. The role of state-owned enterprises has been crucial in shaping this dynamic so that at its peak the public sector and leading mining houses constituted two massive centres of power. This was followed by a thirty-year period of neo-liberal experimentation. The current debate on the 'developmental state' is an attempt to reconstruct the state as a counterweight to capital. It is argued that while the country has moved toward inclusive political and economic institutions, these are both limited by deep 'extractive' characteristics. This transformation failure provides a fertile ground for populism that presents one of the biggest threats to inclusive growth. Cited examples point to the many ways that states have sought to deal with the bonanza that conversion of mineral non-resources into resources brings. Such greenfield resources on state land, or in areas where the state holds monopoly rights, do not present ownership issues. It is suggested that this is the route that South Africa should follow, as the alternative will be conflictual.

Jan 1, 2013

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P205 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

By N. Reddy

The influence of local geology and rock mass characteristics on deformations during a rockburst caused by a controlled blast was studied. This was done by means of visual examination, mapping and photography both before and after the blast. We found that the ejected material was bounded mostly by fractures associated with the bow-wave fracturing and bedding surfaces and that existed prior to the blast. Most of the damage was caused by shake-out. This information is important input for the design of rockburst resistant support systems under conditions of moderate stress.

Jan 1, 2001

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By S. E. Cook

This article uses the case of the Royal Bafokeng Nation to argue that royalties and dividends from mineral resources, if managed well, can provide direct benefits to the surrounding community even while the state collects its share of mining revenues through taxation. The key to this model is the effective management of the resource income flowing into community coffers. Where some of this income may fund urgent interventions in the community, a portion of the income can also be used to establish an intergenerational wealth fund to meet the needs of future generations. As a depleting resource, minerals like gold and platinum are not a sustainable source of income, and must be replaced over time by more regenerative income streams. These strategies and dynamics are manifest in the Royal Bafokeng Nation?s status as both community and quasi-municipality, a labour hosting and a labour sending community, a mine operator and a mine owner. The Royal Bafokeng Nation also owns one of South Africa?s largest community-based investment companies, which channels revenue derived from platinum deposits into a broad investment portfolio that in turn funds an aggressive social development program for 150,000 people living in twenty-nine rural villages.

Jan 1, 2013

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By L Singheiser, W. Willenborg, M. Mueller, K. Hilpert

The limitation of fossil fuel resources and the necessity of reducing CO2emission require an increase of the efficiency of power plants by using combined cycle power systems. Pressurized Pulverized Coal Combustion (PPCC) is a potential concept to realise these objectives. The direct use of hot flue gas for driving a gas turbine requires a hot gas cleanup to achieve corrosion prevention of the turbine blading. One of the main problems is the alkali release during the coal combustion process. Molten coal ash slag has a high potential for alkali retention which depend son the alkali oxide activity in the slag. Knudsen Effusion Mass Spectrometry (KEMS) was used to determine thermodynamic data of alkali gas species over molten coal ash slags and of alkali oxides in molten coal ash slags. The main interest of the investigations focused on the structural dependence of the thermodynamic properties of the alkalis. It was found that there is a strong correlation between the thermodynamic properties and the ratio of nonbridging oxygen to tetrahedral oxygen (NBO/T). An increase of the polymerization of the slag results in a decrease of the alkali oxide activity in the slag and thus a decrease of the alkali partial pressure over the slag. Keywords: coal ash slag, structure, alkali oxide activity, alkali vapour pressure, PPCC, KEMS.

Jan 1, 2004

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

By M. H. Solomon

After the global financial crisis of 2008, African mining is entering anew phase of development. The rapid withdrawal of emerging market funding from the critical exploration and development industries provided a hiatus in funding, a gap which was quickly filled by Chinese and other Asian investors. While the continent is still economically dependent on its extractive industries, the prevalence of Dutch Disease has undermined Africa?s ability to benefit fully from its mining, oil, and gas industries. While the extractive industries are closely related to many of the more fragile and failed states in Africa, it is equally true that the strongest states in Africa have mining-based economies. This paper explores the possible linkages between mining, strong and weak political economies, and poverty in Africa. It draws the conclusion that neither Dutch Disease nor Resource Course is a given in resource-endowed countries, and that it can be avoided if the mining economies in these countries are actively integrated into their respective broader economies and used to foster economic diversification. The author asserts that given the capacity constraints of many African governments, it is contingent on mining companies to become integrally involved in catalysing diversification around their infrastructure and supply chains.

Jan 1, 2011

By Gerard de Vries

pipeline industry and are still growing in size. Liquid epoxy and polyurethanes are an excellent choice for whatever the aggressiveness of the substance transported and whatever the harmful outside influences, maximum protection is required. They can be used as coatings on all kind of pipelines varying from the mainline coating to the field joint coating. Compared with traditional systems like dual layer FBE and 3-layer polyolefin there are some benefits to be considered like easiness of repairs, amount of coats, application temperature and film thickness. The interior coating renders the pipe surface so much smoother that considerable savings can be realized in pump stations. Apart from the interior of the pipeline, the industry is faced with new challenges like higher operating temperatures of lines and an emphasis on product benefits in order to save money. Key words: liquid epoxy, liquid polyurethane, phenolic epoxy, pipeline, field joint coating, internal coating, corrosion control

Jan 1, 2006