Search Documents

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By O. Fenn

Earlier work had shown that the use of water jets at moderate pressure enhances mechanical cutting in hard rock. To assess the potential of this technique for use in conjunction with free-rolling cutters, a series of laboratory tests was conducted with disc and button cutters to determine the effect of variations in the jet and cutting parameters on the cuter performance. In these tests it was found that the use of water jets at pressure in the range 5 to 40 MPa can reduce the forces on a free-rolling cuter by 40 per cent, which represents a significant improvement in cutting performance. The reduction in thrust force was found to be dependent on jet pressure: the greater the pressure, the greater the reduction. The reduction in rolling force was independent of jet pressure over the range investigated. The results indicate that no additional improvements in cutting performance of any significance are to be gained by an increase in jet pressure above 40 MPa. The most effective jet configuration for the reduction of cuter forces was found to be four coherent water jets, two lateraly disposed on each side of the cuter and directed at the arc of contact between the cutting edge and the rock.

Jan 1, 1987

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

By R. Falcon, A. J. Ham

This paper summarizes the characteristics of Southern African coals, presents a fundamental approach to the combustion performance of coal, and reviews some of the recent developments in the fields of technological evaluation and boiler design for coals typical of this region. This includes a summary of the petrographic constituents of coa~ highlighting the differences between the Palaeozoic coals of the northern and southern hemispheres (Laurasia and Gondwana respectively), and the effects of these properties on the combustion performance of coal as seen in terms of laboratory, pilot-scale, and full-scale operating conditions. Recent developments in boiler design linked to advanced characterization studies and commercial experience have led to unprecedented use, with maximum effect, of the low-grade, high-ash, high-inertinite coals typical of some parts of this region. In the light of this success, more adequate understanding and better methods of assessment of the coals typical of the Gondwana region are called for, particularly in the light of the price premium for high-grade coal and the more cost-effective lower grade coals on the international steam markets.

Jan 1, 1988

By C. S. Northcote, I. F. Buchan, L. F. Baars

In 1969 the Coal Division of the Anglo American Corporation was awarded the tender to supply coal to the new 3000 MW power station to be erected at Kriel, which is situated midway between the towns of Ogies and Bethal in the eastern Transvaal. The coal was to be supplied from the No. 4 Seam in the Kriel Area of the Witbank Coalfield. The No. 4 Seam in this area varies in depth of overburden from 75 m to 6 m, with an average of 55 m. Initially, the mine was planned as an underground mine incorporating a three-shaft system for transporting some 8 million tons of coal per annum to the power station. As the result of negotiations between Anglo and Escom to improve the volumetric extraction of coal from the new mine, the Kriel Division of Anglo Power Collieries was finally planned to produce 4,1 million tons of coal from an underground mine and 4,5 million tons from an opencast mine, with a resultant increase in volumetric extraction. This paper describes the opencast operation at Kriel, with particular reference to the water problems encountered and to the operation of the draglines on sloping ground to a depth of 40 m to the top of the coal seam.

Jan 1, 1980

By C. L. E. Swartz, I. J. Barker, J. H. Schubert

A dynamic simulator of the leaching and adsorption cascades of a gold plant was developed and used to compare the effect of various disturbances on the overall efficiency of the plant. These comparisons show which disturbances most critically need to be controlled to optimize plant performance. The simulator was based on an existing gold plant. Dynamic and steady-state data were collected on the plant and were used in the modeling of the process. Simple dual-rate models are used to describe the leaching and adsorption processes. Mole-balances of various species take into account the changes of concentrations in the leach, and also the movement of pulp and carbon up and down the adsorption cascade. Fluctuations in the flow rate, density, and cyanide concentration of the feed to the leach have a negative effect on the efficiency of the leach, while carbon attrition was found to be an important factor in decreasing the efficiency of the carbon-in-pulp (GIP) section. Badly regulated transfers contribute towards the decreased efficiency of the GIP section, but overflows and carbon leakage have only a limited long-term effect. Various carbon profiles and transfer schemes were studied, and the results indicated that a slightly heavier loading at the bottom of the cascade is beneficial, while the type of transfer is relatively unimportant.

Jan 1, 1993

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By D. G. Krige

Using a very large number of chip-sample values from a mined-out area of the Hartebeestfontein mine and accepting these as equivalent to borehole values (also areas of 1 km by 1 km as equivalent to 'mines'), the authors apply a series of borehole-valuation procedures to these 'mines', Large undeveloped sections of existing mines are also regarded as the equivalent of such 'mines'. These procedures start with the orthodox arithmetic mean and then introduce additional information in the form of the Iog normal frequency distribution model for Sichel's 't' estimator. Knowledge of the average log-variance within mines leads to the tH estimator. The mean grade of the 'family' of mines to which a new mine belongs is then introduced via regression or elementary kriging. Next, further information on the macro spatial structure of the grade is used, together with the grades of adjacent existing mines in ordinary and simple macro-kriging procedures; finally, via the distribution model, the grade is seen as a function of the logs of the grades and their variances. These are introduced as spatial variables, and both are estimated by macro-Iog normal ordinary and simple kriging procedures with grades and variances from adjacent mines'. Comparisons are also made between macro-kriging on lognormal transformed values versus untransformed values. Conclusions are drawn on the relative importance of the various items of additional information used, on the procedures followed, and on the significance of the advantages gained

Jan 1, 1992

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By G. Ferrara

The mathematical framework of a well-established model proposed earlier by the authors for the screening process is briefly recalled. Some numerical methods for the application of the model, concerning numerical solution of the equations and parameter estimation, are indicated. Some applications of the model to improve screening operations, sizing of screen, simulation of screening and of integrated plant operations are discussed, and the computer software to be used for these purposes is described in detail.

Jan 1, 1987

By S. Budavari

The effects of shaft pillars left in deep-level hard-rock mines during the extraction of tabular deposits were studied some time ago, resulting in the formulation of design principles and procedures, which have been used with success in the design of shaft pillars in the deep-level gold mines of South Africa. The method has not yet been utilized in the design of shaft pillars in shallow and moderately deep hard-rock mines. The purpose of the present study was to remedy the situation since a great number of deposits are worked at those depths. The object of this paper is to present governing equations for the components of stress and differential movement as derived by use of an elastic model. The pillar is taken to be circular in the plane of a horizontal deposit. On the basis of the numerical results obtained, a study was made of the distribution of the vertical strain and tilt along the axis of the shaft, and of the vertical stress along the shaft and across the pillar. In every case investigated, the most adverse geometry was taken into consideration. By use of an empirical criterion and the results of some in situ observations, the determination of pillar dimensions and differential displacement components for South African gold-mining conditions is demonstrated. Pillar dimensions for shallow and moderate depths are compared with those accepted for deep-level conditions.

Jan 1, 1986

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

The special mixing requirements for backfilling are discussed, and the problems associated with the mixing of coarse and deslimed slurries, as well as the tailings from the gold plant are outlined. The mixing of binders which are used to strengthen backfill and the parameters for the scale-up of mixer pilot plant work are also discussed

Jan 1, 1988

Traditionally, the term `total system' design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal `total systems' approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

Advances in extractive metallurgy, 1977. Proceedings of the third symposium organised by the Institution of Mining and Metallurgy held from 18-20th April 1977. London, the Institution of Mining and Metallurgy, 1977. 244 pp. £18,50. Coal preparation A meeting of the Organising Committee of the Eighth International Coal Preparation Congress took place in Moscow on 24th and 25th May, 1977. Representatives NIM reports Report no. 1906 An automated instrument for measuring the effects of impurities on cathodic-current efficiency during the electrowinning of zinc. (2nd Sep., 1977). Report no. 1908 An analysis of the replies to a questionnaire on materials of construction for ore hoppers. (16th Sep., 1977). Report no. 1913 The mechanism and rate of reduction of Mamatwan manganese-ore fines by carbon. (2nd Sep., 1977). Report no. 1914 The thermodynamics of the formation of sulphate complexes of iron (111), cobalt (11), iron (11), manganese (11), and copper (11) in perchlorate medium. (15th Sep., 1977). Report no. 1924 The composition of chromite grains from varwUB Witwatersrand reefs. (23rd Sep., 1977). Atomic absorption The Perkin-Elmer Corporation of South Africa is planning to hold an Atomic Absorption Autumn School in Cape Town from 10th to 13th April, 1978. Travel bursaries Two Atlas Cop co travel bursaries for study tours of Swedish mines may be awarded annually to young mining graduates. Stability in coal mining The First International Symposium on the above subject is to be held in Vancouver (Canada) on 5th to 7th April, 1978.

Jan 1, 1978

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

By G. Y. Nisbet

The contribution made to the economy of South Africa by the-minerals industry is discussed according to four of its aspects. Firstly, the industry supports both students and lecturers in technical and academic institutions. This support covers virtually the whole range of courses available at the universities and technikons, although most is obviously devoted to the engineering and science faculties. Secondly, the industry makes a direct financial contribution to the State in that it contributes about40 per cent of the State's receipts from direct tax paid on incomes and 30 per cent of the contributions to the total State revenue. It provides employment for 28 per cent of the total active labour force, and contributes 24 per cent directly to the gross domestic product. Thirdly, the industry is responsible for over 65 per cent of the country's foreign earnings in spite of the significant rise in exports from the manufacturing sector. South African minerals are of crucial importance to the word, since the country has the world's largest reserves of seven minerals and features very prominently in many others. Finally, the industry makes an indirect contribution, referred to as the multiplier effect. This is the ripple effect on the economy made by a large injection of momey by which that money acquires an added effective value. A study made of the total production of the mining industry in 1978, for instance, showed this multiplier to havea value of 1,5. Thus, if this effect is included, the industry's contribution to the gross domestic product is 44,S per cent. Similarly, the industry is responsible for the creation of jobs both within itself and in other industries, which could amount to 100000 for the period 1981 to 1935.

Jan 1, 1981