Search Documents

By T. Wallmach

Heavy mineral deposits are a source of the economic important element titanium, which is contained in minerals such as ilmenite, pseudorutile and rutile. In the Ranobe heavy minerals deposit these minerals occur not only as primary unaltered minerals but also display various degrees of alteration resulting in an increased titanium content of the deposit. The presence of the various FeTi-oxide minerals? textural relations is a reflection of geological processes and may ultimately be used to unravel the geological history of the deposit. These minerals have different chemical and physical properties that influence metallurgical tests and the quality of products produced from various mineral beneficiation streams. It is therefore of metallurgical importance that the minerals are well characterized, defined and monitored during preliminary beneficiation tests.

Jan 1, 2007

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L'article décrit l'application des méthodes de modélisation continue/discontinue pour l'étude des conditions de stabilité de la mine d' Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d'estimer les conditions de stabilité de l'amas rocheux au terme de l'exploitation de la mine susmentionnée. La modélisation continue a impliqué l'application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing `Mine to Mill' or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change - both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices - so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or `buy in'. Ensuring this buy in continues is the challenge facing every company involved in PIO work - but the benefits are well worth it. This paper will review MMPT-AP's experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-AP's involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By S. J. van Wyk, A. S. H. Haagner, A. Abraha

Opencast coal mining is responsible for the greatest area of land disturbance across all of the commodity types in South Africa. Many thousands of hectares have been rehabilitated to date and, although rehabilitation performance is not always measured or reported, a significant database, spanning 24 years, has now been analysed to identify the main shortcomings holding back rehabilitation sustainability across the industry. Data from 48 different collieries with rehabilitation performance scores measured from 2000-2024 were analysed. A standardised assessment framework was implemented at all 48 collieries, focusing on aspects of land capability, soil fertility, landscape form and drainage, vegetation species composition and basal cover, implementation of maintenance programmes, and prevalence of invasive alien plants. The findings show that, although invasive species management, plant species composition, and plant basal cover are often adequate, the implementation of aftercare and maintenance programmes (influencing soil fertility) and deficiencies in overall landform design and drainage systems are most significant in preventing overall rehabilitation progression and self-sustainability. Integrating these during design and rehabilitation execution, followed by intensive maintenance (especially in the first five years post-topsoiling and seeding) will be key for the overall industry performance to improve to acceptable levels. The database is biased towards collieries that actually do undertake rehabilitation and that do measure it, hence the actual industry performance is likely worse than what is presented. Due to the substantial hectarages involved and the main post-mining land uses being grazing and crop production, the industry cannot afford to keep perpetuating deficiencies in achieving the foundational aspects of rehabilitation that would pave the way for sustained economic future use.

Apr 25, 2025

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the Theory of Sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of a long chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even log-normal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2009

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By R. M. G. Machunter

The use of testwork to establish an economically feasible separating plant has been a long established practice in the mineral processing industry. However, uncertainties in orebody characteristics and equipment/plant operation can have a significant impact on the separation performance of a given project. This paper explores the impact of uncertainties derived during testwork at key processing stages on the overall performance of mineral processing flowsheets. Case studies for both mineral sand and iron ore projects will be used to illustrate the concepts studied in this paper.

Jan 1, 2007

By K. Grossauer, W. Schubert

For tunnelling in poor and heterogeneous ground a reliable on-site short-term prediction is required to allow a safe and economical construction. With the use of absolute displacement monitoring data and advanced software for evaluation of the data in combination with a routine update of the geological model a considerable increase in the reliability of the short-term prediction could be achieved. The paper deals with theoretical considerations, numerical studies and case histories from alpine tunnels in heterogeneous rock. Tunnelbau in schlechtem und heterogenem Gebirge erfordert auf der Baustelle eine verlaessliche Kurzzeitprognose, um ein sicheres und wirtschaftliches Bauwerk gewaehrleisten zu können. Die Verwendung von absoluten Verschiebungsmessdaten und deren Auswertung mit Hilfe von hoch entwickelten Softwareprogrammen in Kombination mit einer laufenden Aktualisierung des Gebirgsmodells ermöglicht eine erhebliche Erhöhung der Verlässlichkeit von Kurzzeitprognosen. Dieser Beitrag beschäftigt sich mit theoretischen Ansätzen, numerischen Modellen und Fallstudien von Tunnelvortrieben in heterogenem Gebirge. La construction de tunnels dans la montagne hétérogène de faible résistance exige un pronostic fiable à court terme sur le chantier, afin de pouvoir garantir un ouvrage sûr et économique. L'utilisation des données de mesure de décalage absolues et de leur évaluation à l'aide de logiciels sophistiqués en combinaison avec une mise à jour courante du modèle de la montagne permet une augmentation considérable de la fiabilité des pronostics à court terme. Cette contribution présente des approches théoriques, des modèles numériques et de cas pratiques de progressions de tunnels dans des montagnes hétérogènes.

Jan 1, 2003

By S. K. Mahata, P. G. Suresh Kumar, B. B. Singh

Improvement of post tap hole practices is achievable by mechanized handling of melt during the production of Ferro Chrome, resulting in higher recovery of chromium. The paper deals with modern practices adopted in the production of ferro-chrome since past two decades. The methods and practices deal with various areas : a) Improved method of operating the tap hole by selection of right quality of refractory to maintain the life of tap hole. b) Collection of melt in different types of receptacles like refractory brick lined mild steel ladles, cast steel ladles, cast iron pans being chosen for cost effective and efficient handling. c) Separation of slag and metal, casting of metal, crushing, sizing and stock piling etc. d) Slag disposal and recovery of entrapped metal. The drive behind the above development is continuous improvement, which results in higher chromium recovery and reduces loss of metal in slag by completely mechanized method so as to be at the same level with producers of ferro-chrome in other advanced countries , in the emerging global economy.

Jan 1, 2007

The statistical methods described in the previous chapter permit the estimation of the average value p of a deposit, and the calculation of confidence limits for this value. They are based on the assumption of independence of sample values. As soon as a reasonable number of samples has been obtained from a deposit, local valuation, or estimation of blocks of ore within the mineral deposit, becomes necessary. The assumption of independence of values must then be rejected. Local valuation is possible only if there is a relationship between the value of a sample and the value of the surrounding ore, provided this relationship is a function of the position of the sample with respect to the blocks of ore to be valued. Whichever method is used for the valuation of a block of ore, the following assumptions are always made: ? The values of samples located near or inside the block are related to the value of the block. ? The values of the samples located closest to the block are most closely related to the value of the block. These assumptions will hold true only if the following assumption can also be made: ? There exists a relationship between sample values which is a function of the distance between samples. We are saying that the value x (z) of a sample centred at a point z has properties which are functions of this point. A certain spatial structure exists in the sample distribution. We are therefore dealing with a regionalized phenomenon, and we must treat x (z) as a regionalized variable. This can be done statistically by means of a model chosen to represent the spatial structure of the phenomenon. We shall see that the relationship between block values and sample values can be deduced from the relationship between sample values, and all local valuation problems can be solved using the statistical model obtained from the analysis of the sample values. It is important to realize that this statistical model is obtained by analysing the properties of known sample values, and will be used for the estimation of unknown block values. Such a statistical inference is valid only if the model developed represents the properties of both the sampled section of the ore body and the section to be valued: some stationarity conditions must be satisfied, and the model with the least restrictive conditions is preferred. In the following chapters, the most important models used in spatial geostatistics are presented. The models which can be used when there is no significant drift (trends) in values are described in Chapters 3-1 1. These models can also be used to solve some specific valuation problems when a linear drift is present. A general study of the more difficult problem of analysis of an ore body whose values present a drift is described in Chapter 12. Note that the area considered for local valuation of a block of ore is often small enough for any drift which might be present to be ignored.

Jan 1, 1978

By V. K. Risinggård, M. Sparta

We report on the development of a finite-element method model for a pilot furnace for the production of manganese alloys. The model is a multiphysics model that addresses material flow, electrical conditions, heat transfer, and physical and chemical transformations. It is capable of studying both quasi-steady and transient states in time-dependent simulations. The model includes common charge materials and fluxes and can simulate production of both ferromanganese and silicomanganese alloys with acid and basic slags, as well as changing charge compositions. The model output provides access to the material distribution in the furnace during furnace runs, temperature profiles, current paths, energy balances, and alloy and slag production rates and compositions.

Apr 16, 2024

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024

By G. Segaetsho

"Conventional blasting rules of thumb used to develop blast designs are based on parametric ratios, with insufficient consideration of the rock mass factors that influence the achievability of final wall designs. At a hard-rock mine in Botswana, catchment berm designs were frequently unachievable, which exposed the mining operation to safety hazards such as local wallrock failure from damaged crests, frozen toes, and rolling rockfalls from higher mining levels. Increased standoff distances from the highwall reduced the manoeuvring area on the pit floor and the extraction factor that was safely achievable. Application of rock mass classification and the Blastability Index (BI) as a means to improve wall control was investigated. Zones were defined according to rock types forming the western highwall rock mass, and distinguishing rock mass classification factors were used to establish the suitable wall control designs. The approach combined rock mass classification methodologies such as the Geological Strength Index and the Rock Mass Rating, and related them to the BI and discontinuities of the rock mass to produce a design input tool that can be used to develop objective wall control designs. The designs driven by the tool inherently take into account the rock mass characteristic factors at the centre of the rock mass classification methods mentioned above, and significantly reduce the dependence on rules of thumb. It was found that this approach produces designs with explosive energy measures that are consistent with the required rock-breaking effort and the behaviour of discontinuities, while preserving perimeter walls.IntroductionBlasting is the first step in the comminution process. Various coordinated inputs contribute to its success, and in turn to the efficient execution of processes that lie downstream from the blasting step. Primary to meeting production and operational objectives of a mine, as well as the protection of human life and the mineral resource, is the achievement of highwall design specifications and competence. To this end, this study investigated the use of existing tools and knowledge for the achievement of highwall control goals at a hard-rock mine in Botswana."

Jan 1, 2018

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019