Search Documents

By El-Sayed M. Sherif, J. D. Comins, Erasmus R. M.

Corrosion of copper in aerated acidic chloride pickling (0.5 M HCl) solutions and its inhibition by 3-amino-1,2,4-triazole-5-thiol (ATT) have been investigated using electrochemical techniques and weight-loss measurements, along with Raman spectroscopy. Electrochemical measurements for copper after varied immersion periods of 0, 24 and 48h showed that the presence of ATT and the increase of its concentration significantly decrease cathodic, anodic, corrosion (jCorr) currents and corrosion rates (KCorr), as well as the dissolution currents at 300 mV vs. Ag/AgCl, while increase polarization resistance (Rp), degree of surface coverage (?) and inhibition efficiency (IE%) to a great extent. Weight-loss measurements after different immersion periods of 6 ~ 48h revealed that the dissolution of copper decreased to a minimum and the corresponding IE% increased with ATT concentration increases. The detection of ATT molecules on the copper surface by Raman spectroscopy indicated that inhibition of copper corrosion is achieved by strong adsorption of ATT molecules onto the copper surface. Aerated acidic pickling solutions; 3-Amino-1,2,4-triazole-5-thiol; Copper corrosion; Corrosion inhibition; Raman spectroscopy

Jan 1, 2006

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

By N. B. Devi

The extraction of Cu(II) from HCl media using Cyanex 923 in kerosene was investigated. The effect of shaking time, aqueous phase acid concentration, extractant concentration, chloride ion concentration, various metal ions (Mn2+, Mg2+, Fe2+, and Ni2+), and temperature on the extraction were studied. Using 0.1 M Cyanex 923 the extraction of Cu(II) was 6.7 per cent from 3 M HCl, which increased up to 78.5 per cent with 6.5 M HCl and then decreased due to acid extraction by the extractant. The maximum extraction (97.5 per cent) was obtained with 1 M Cyanex 923 from 5 M HCl solution. A mathematical model has been developed to describe solvent extraction equllibria over wide ranges of concentration of extractant, acid, and chloride ions. The composition of the extracted species has been predicted on the basis of slope analysis results and extraction equilibrium modelling. The negative values of enthalpy change and entropy change confirm the exothermic formation of the extracted complex.

Jan 1, 2012

By M. Dworzanowski

The difference in the magnetic properties of minerals is the basis for magnetic separation. All minerals can be generally classified as ferromagnetic (strongly magnetic), paramagnetic (weakly magnetic) or diamagnetic (non-magnetic). Magnetic separation can be conducted dry or wet. The majority of the applications of wet magnetic separation in the mining industry are based on the wet drum magnetic separator. The wet drum magnetic separator has been in use for over 50 years and its design is based on a rotating drum installed inside a tank. Inside the drum are stationary, permanent magnets arranged in an arc to provide the magnetic field. These magnets can be of the ceramic ferrite type providing a low intensity magnetic field or of the rare earth type providing a high intensity magnetic field.

Jan 1, 2010

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By M. Nicolle

The Tati Activox® Project will be the first full-scale implementation of the patented Activox® process (The Tati Activox® project was deferred in 2008. Please refer to the Norilsk Nickel press issue on the topic for more info). The process was developed by Norilsk Process Technology and has been tested on Tati mine sulphide concentrates in laboratory, pilot and demonstration plant scales and demonstrated its viability. There are inherent risks to the final scale-up of the process from the demo plant and one of them will be investigated in this paper. Compartment 1 is designed to leach approximately 77% of the total nickel leached. For this reason agitation requirements in the first compartment of the autoclave are reviewed. An attempt is made to minimize the process and mechanical risks associated in achieving oxygen mass transfer into the slurry solution. The agitator powers for oxygen mass transfer are calculated using empirical correlations and compared to demonstration plant testwork. The resulting gassed power per unit volume (P/V) is higher than most commercial autoclaves and raises uncertainty on the viability of using such high unit power inputs. Additionally, there is concern about the ability of the autoclave shell to withstand and support the higher loading of large agitators. An alternative solution to designing for the increased P/V is assessed in which the number of compartments within the autoclave is reduced from 5 to 4 by removing the compartment wall separating compartments 1 and 2. This results in an enlarged first compartment containing 3 agitators instead of 2. Therefore the compartment 1 oxygen demand is supplied through 3 agitators, which lowers the P/V per agitator. The reduction in the number of autoclave compartments raises the potential for short-circuiting the mean flow pattern by slurry particles. Short-circuiting and low velocity zones could result in a lower recovery of metal and localized hot spots, respectively. A computational fluid dynamic (CFD) analysis was conducted to quantify these concerns and also to evaluate further design considerations. The results indicate that the proposed design change to 4 compartments affects short-circuiting. The impact of increased short-circuiting on the overall autoclave recoveries is not quantified, however; it is expected to be negligible based on testwork done in the Tati Demonstration Plant and similar modifications made to another operating autoclave. The CFD analysis also suggests that there will be no low velocity zones within the compartment.

Jan 1, 2009

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By Sönke Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s and is recognized a shaving significant potential for optimizing production scheduling problems for both surface and underground mining. The major problem in long-term production scheduling for underground orebodies generally relate to the large number of variables needed to formulate a MIP model, which makes it too complex to solve. As the number of variables in the model increase, solution times are known to increase at an exponential rate. In many instances the more extensive use of MIP models has been limited due to excessive solution times.

Jan 1, 2010

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore , gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By F. T. Cawood

This article offers a personal and independent view on the threats to the sustainability of the South African minerals industry. It argues that if the six identified threats of insufficient spending on research and development, general standard of education, nationalization, inadequate infrastructure, Aids prevalence and labour inefficiency are not acted upon as a matter of urgency, the future of the mining industry, along with its important contribution to the economy, is at risk.

Jan 1, 2011

By L. A. Sandham

Environmental impact assessment (EIA) in South Africa is administered by the Department of Minerals and Energy (DME) for the mining industry, and the Department of Environmental Affairs and Tourism (DEAT) for all other sectors. Thus far, EIA research has focused on the process under the auspices of DEAT but none has focused on the EIA process that has been mandatory in the South African mining industry since 2004. Using the Lee and Colley(Lee et al.13) review package as a basis, a review model specifically tailored to the needs of the mining industry was applied to review the quality of a sample of 20 environmental impact reports (EIRs)approved by the DME. Results reveal that 85% of the EIRs are of a satisfactory quality. Presentational and descriptive components generally achieved higher quality grades than the analytical components such as impact magnitude and alternatives. The results show that in spite of some areas of weakness, and in spite of being conducted in terms of different legislation, EIR quality in the mining sectors appears to conform to the overall standard of quality of EIRs in other sectors in South Africa, and is also on a par with quality abroad. Hence, despite the criticism that DME is usurping the role of DEAT, it is concluded that EIRs of comparable standard are being produced, and that the quality of EIRs in the mining sector do not provide supporting evidence for this criticism. However, EIR quality is only a single aspect of EIA effectiveness, others including action and implementation of EIA proposals and mitigation measures.

Jan 1, 2008

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore, gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

By A. P. W. Briggs

Difficulties with the screening of large volumes of pulp to remove plus 600 /km material before the adsorption circuit and to retain plus 20-mesh carbon in the adsorption contactors have largely been solved, with the result that the plant can now handle its design throughput. The elution and electrowinning processes have been modified to simplify the circuit, but the regeneration of carbon remains unsatisfactory. The production of fine carbon in the plant can lead to increased gold losses, and this carbon must be collected and treated. Collection methods for fine carbon and some indications of the quantity of the carbon and its gold values are given.

Jan 1, 1983

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005