Search Documents

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

By C. W. Lee

"Introduction of diesel engines in underground mines may generate severe health hazards associated with exhaust contaminants. One of the most important parameter in determining the optimal air quantity for hazard reduction is the exhaust dispersion. Through analyzing the exact solution of the diffusion equation and its approximation by finite difference method(FDM) , this paper aims at doing a fundamental research to find an efficient dispersion model suitable to the domestic mines. Diffusion coefficients are likely to be small in the underground airways with high ventilation resistance. This makes concentration profiles similar to the convection-based step functions. It is the case for fixed as well as moving engines. Concentration estimation by exact solution is almost impossible in the case of either a single engine moving at a variable speed or the existence of multiple engines. Application of FDM to the diffusion equation including turbulent dispersion results in the various problems; unstable concentration profiles depending on the engine location, nuctuating concentrations near the engine, and overestimation of the dispersion region of which error grows with waning diffusion coefficient.Convection-based dispersion model is found to fit well for dynamic simulation of exhaust dispersion from multiple diesel engines in the airways showing low diffusion coefficients. Its suitability is more likely in the regions with frequent equipment passage. Published"

Nov 1, 1995

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Martyn F. Roetter

The work of the operational communication systems' group dealt with a range of communication needs and functions within mines, primarily along haulageways, to and within sections up to the working face itself, and in mine shafts. A mixture of communication techniques and hardware is needed to satisfy this variety of communication needs within the differing environments encountered in U.S. mines. Substantial progress, both experimental and theoretical, has been made in recent years towards developing alternative communication systems suitable for use in mines which are based on "guided" waves, including wire-less (waveguide-like propagation in mine tunnels) and wire-based systems (leaky coaxial cables or wires) . Major priorities identified for further work needed to confirm (or deny) the applicability, and refine the operational specifications of promising communication systems for mine use include: Short-Term Projects o Cost/performance analyses of promising leaky coaxial cable and UHF radio communication systems which require further data from: - Experimental investigation under U.S. mine conditions of the performance of potentially applicable leaky coaxial cable communication systems developed in Europe (France, Belgium, and the U.K). - Cost estimates on these coaxial cable communication systems. - Measurements of UHF radio propagation in low-coal mines. - Investigation of the influence of obstacles (e.g. shuttle cars and section machinery) in the entries on UHF radio propagation in mines. o Investigation of the problems of transmitter and receiver coupling and termination matching associated with the two-way propagation of low frequency radio waves in hoist shafts.

Jan 1, 1973

By Oliver Bowles

"In a previous report of the Bureau of Mines (Serial No. 2080 reference was made to a fatal accident from falling rock in a quarry in Utah, and ways of avoiding such accidents were pointed out. A fatal accident similar to it in some respects recently occurred in a limestone quarry in Maryland. All operators of stone quarries are desirous of reducing accidents to a minimum, and almost without exception they welcome any suggestions having in view the establishment of safer quarry practice. It is believed, therefore, that a brief outline of the cir-cumstances surrounding this later accident may be of practical advantage to quarry-men, as it may serve as a guide to them in so conducting operations that such unfortunate occurrences may be reduced in number.The quarry where the accident occurred is in form a circular pit 500 to 600 feet across an 80 to 100 feet deep. The rock is a dense limestone with the beds dipping at an angle of 35 to 45 degrees from the horizontal. Numerous erosion cavities in the form of pockets or narrow spaces following joint planes are filled with red sand and clay. They are confined largely to the upper 20 or 30 feet of the deposit. Open bedding planes are 4 to 10 feet apart toward the surface, and are spaced at wider intervals toward the base of the quarry. The open bedding planes present smooth uniform rock surfaces that dip steeply into the pit at the northeast side of the quarry opening. These smooth surfaces constitute a source of danger, as they may permit loose material to slide into the pit.In this particular instance a blast had been discharged, throwing down a mass of rock for steam-shovel loading. Three men wore employed thereafter for a period of about two days in cleaning down all loose material that might be dangerous to workmen luring the loading process. A mass of red sand and clay in which several large bowlders were embedded was left on one of these slanting surfaces, for the material seemed to be sufficiently secure to be quite safe. The lower edge of the slanting surface was about 25 feet above the quarry floor. The quarry conditions are illustrated in fig. 1, where (a) represents the quarry floor, (b) the vertical quarry (c) the slanting joint plane surface, and (d) the rock and earth resting on the surface."

Dec 1, 1921

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

Objective A cable bolt can be a strain-measuring device as well as a supporting device in underground mines. Placing instruments on a cable bolt allows certain characteristics of a rock mass, such as high strain and load, to he evaluated during mining and provides a means for mining engineers and mine inspectors to forecast a potential roof fall. Background Thousands of cable bolts are installed in U.S. mines each year. Studies performed by NIOSH researchers show that support loads can exceed the yield point of the steel, which can result in unstable ground conditions that pose direct safety hazards for underground workers. Rock falls can also create secondary hazards, such as caved escape ways and blocked ventilation passages. Development of methods and tools to assist in the evaluation and selection of rock supports could reduce the number of unplanned rock falls significantly. Approach Instrumented cable bolts developed at NIOSH’s Spokane Research Laboratory were used along with existing ground control systems to monitor rock mass loads and movement Axial and shear loads on the cables are determined as these loads are transferred to strain gages embedded in the king wire. In longwall, room-and-pillar, or underhand cut-and-fill mines, rock mass loads and movements can be detected down to microstrains of stress or millimeters of movement. By detecting such small amounts of ground movement and support load, early intervention to prevent a roof fall is possible, and miner safety and health are increased. How it Works Up to 10 strain gages are embedded in the king wire at whatever locations a mine ground control engineer may specify. The gages m either be set in pairs in the same plane to detect shear or set at 90° angles to detect loading in three dimensions. The cables are up to 5 meters long if they arc to be grouted with resin or up to 15 meters: if they will be grouted with cement. They arc capable of holding m ultimate lend of 214 kN and produce reliable readings to 178 kN, as shown in the calibration curve. The cables are fitted with an instrument plug for monitoring the gages and a special head for insertion into the rock. A data acquisition system, such as a Vishay strain indicator box, Campbell Scientific, or Omnidata system, is required to obtain the data for load and displacement calculations.

Nov 1, 1998

This section contains a summary of our investigation of the soil conditions (type, porosity, moisture content, etc.) at the two sites (Lanse and Kato, Pennsylvania) selected for field testing of latex as a soil sealant. Other natural conditions such as rainfall, frostline, depth of the water table, etc., were also measured and recorded for possible later use in assessing the effect of the latex seal on the total environment. The numbered sites referred to throughout this report are shown on the maps of the Lanse and Kato sites (Figures 1 and 2). KA, RB and KC are positions at the Kato site - all other numbered positions refer to the Lanse site. Two other terms used throughout the report which should be explained are “horizon” and "profile". These are synonymous terms for soil layer, A horizon (or A profile) referring to topsoil and B horizon (or B profile) referring to subsoil. The properties that control the flow of water through the soil are of special interest because these will also govern the passage of a sealant into and through the soil. Normally the particle size distribution is a good measure of soil permeability, which is directly proportional to sand content and inversely proportional to silt and/or clay content. Tables I1 and I11 show the percentages of gravel or stones, sand, silt and clay of Lanse and Kato soil samples. According to the United States Department of Agriculture classification, the gravel is ,ignored and the residue separated into sand, silt, and clay fractions. Figures 4 and 5 indicate by means of the USDk soil texture triangle that the variability of composition of Lanse soil ranges from sandy loam in the creekbed to clay loam. The variation is even greater among soil samples from Kato. Porosity of soil, also known as percent voids, is another indication of how readily water will travel through soils. Soil density usually increases and porosity decreases with depth, and as expected, the porosity of the top soil at Kato, a forest, is exceptionally porous and open (see Table IV) The pore diameter and length of soil capillaries is extremely variable, and its distribution in the field is impossible to determine. In addition to the capillaries, soil also contains many macro cracks, crevices, and passages around stones and roots. All these affect the flow rate of water through soil. Poiseuille's law states that the rate of flow of a liquid through a narrow tube is proportional to the 4th power of the radius of the tube. Pore size normally decreases with depth and in soil containing appreciable amounts of silt and clay this is especially true. Thus, deeper soils should be less permeable and such was the case at Lanse and Kato.

Jan 1, 1972

SMCRA contains five principal regulatory provisions that form the basis for its implementation: Performance Standards Performance standard safe intended to ensure that all surface mining is conducted in a way that protects the environment and the public and ensures that the mined land is restored to productive use following mining. Permits Before developing a surface or underground coal mine, an operator must have a permit issued under SMCRA. An application for a permit to conduct a surface coal mining operation is a detailed document that consists of text and numeric data describing the proposed mining and reclamation. Information must be furnished on pre-mining environmental conditions, existing land use, proposed mining and reclamation, how the performance standards will be met, and the post-mining land use. This provides the regulatory authority with the information necessary to determine that the operation can be conducted in accordance with the regulations. Performance Bonds Before a permit can be granted, an operator must post a performance bond sufficient to cover the cost of reclaiming the site in the event the operator fails to complete reclamation. The bond is not fully released until all performance standards have been met and reclamation of the site has been determined to be successful after five years in the East and Midwest, and after 10 years in the arid West. However, the bond can be partially released as various phases of reclamation are completed. Inspection and Enforcement If a violation of SMCRA or of a state surface mining and reclamation law is observed, an inspector issues a notice of violation to the operator. The violation must be corrected within a specific time, and the operator may also have to pay a fine based on the severity of the violation. If the violation is not corrected, acessation order is issued to immediately stop active coal mining, and the operator must pay a fine. If a violation is especially serious (for example, creates an Following reclamation, the land was immediately put back into agricultural production. Today, grain and corn crop yields have continually exceeded targets. 2 imminent danger to public health or safety or causes significant damage to land, air, or water resources) the inspector immediately issues a cessation order. An operator must correct all violations in order to obtain permits for new mines. Lands Unsuitable For Mining Congress recognized that certain coal deposits cannot be mined without permanent damage to unique cultural or natural resources. As a result, SMCRA protects these resources in two ways: It prohibits mining within the boundaries of national parks, forests, wildlife refuges, trails, wild and scenic rivers, wilderness and recreation areas; in areas which will adversely affect sites listed on the National Register of Historic Places; and within a restricted distance of occupied dwellings, public roads, buildings, parks, schools, churches, and cemeteries; and Provides a process that allows anyone whose interests may be adversely affected by proposed mining to petition to have specific lands designated unsuitable for mining.

Jan 1, 1992

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.