Search Documents

By Michael D. Fenton

The modest mineral industry of Afghanistan continued to suffer adversely from internal disorders that were essentially the result of the continued presence of elements of the armed forces of the U.S.S.R. Despite press reports near yearend intimating that the Soviets might reduce troop strength in Afghanistan, there were no indications of any significant numeric reductions. Indeed, there were clear demonstrations of heightened military actions along the Afghani-Pakistani border, including bombing raids on settlement sites for Afghanis within the territorial limits of Pakistan, actions hardly demonstrative of conditions indicative of Soviet withdrawal.

Jan 1, 1988

Develop a method of dewatering ultrafine mineral waste that will increase water recovery from the waste and produce a dewatered material that eliminates the need for large settling ponds. Background In the hydrometallurgical treatment of many ores and concentrates to recover mineral values, slurries of fine particles are generated. Some of these slurries settle slowly and are difficult to dewater. This inherent property causes environmental and handling problems for the minerals industry. Examples of such problem wastes are clay wastes generated during the mining and beneficiation of phosphate ores, the processing of coal to produce a low-ash material, the cleaning of bentonite, beneficiation of potash, and the recovery of mica from clay-containing ores. At the present time these waste slurries are treated by techniques such as impoundment, thickening, and thickening followed by filtration. But factors such as new environmental regulations, the loss of mineral values in the waste slurries, the need to recycle water in the processing facility, and the lack of land suitable for impounding the waste have shown that new technology will be needed in the future to handle waste slurries.

Jan 1, 1986

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

By Donald N. H. Chi

This Bureau of Mines report is concerned with a theoretical study of the aerodynamic response of a single mine entry to flame-induced disturbance. The unsteady, one/dimensional, compressible flow equations were solved using the method of characteristics. This study was primarily undertaken to determine the feasibility of extending the method of characteristics to study the aero-dynamic response of complex mine networks. It was demonstrated that although the technique has merit in studying the complex wave interaction in single entries, it appears to be too unwieldly and too expensive for network analysis. Effort was also directed at a further study of the dispersion and filtering characteristic of aerodynamic disturbances in mine passageways.

Jan 1, 1975

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

By W. J. Fene

"The prevalence of accidents in the coal-mining industry has prompted a study of the workmen's compensation laws of the various States and the statistics of accident costs, for the purpose of explaining to operators how the compensation laws are regulated and to show the cost of accidents.The subject of compensation laws and accident costs is by no means new, but the prevalence of coal-mine accidents would indicate that the mine operator in general is not thoroughly conversant with their importance. Unquestionably, compensation laws are a large factor in promoting accident prevention, and it is believed that a greater measure of success would be accomplished in preventing accidents if all mine operators were fully aware of their important bearing on the cost of production.Many operators seem to be indifferent to accident occurrence; possibly they do not real¬ize the seriousness of the accident hazards that exist in their mines, even after the hazards are brought to their attention. There is no question that material financial advantages are to be gained by the prevention of accidents and it would appear that when these advantages are thoroughly understood, operators would be anxious to eliminate, insofar as is feasible, conditions likely to cause accidents.The unsettled state of the mineral industry and the irregular operation of mines during the past several years has probably been an important factor in influencing the apparently indifferent attitude of the operator. The chaotic conditions in the mining industry and especially in coal mining are unquestionably a factor that tends to increase accidents, just as mine idleness increases roof hazards and results in deterioration in mechanical, electrical, and haulage equipment, and promotes disorganization of the personnel. During such times greater efforts should be exerted toward the prevention of accidents because of these increased hazards and of the financial advantages brought about by the various savings to be effected when mine accidents are held to a minimum.This report on accidents in the coal mines of Pennsylvania was made possible largely through the cooperation of William J. Maguire, director, Bureau of Statistics, Pennsylvania Department of Labor and Industry, and Rush N. Hosier, superintendent, Coal Mine Section, Pennsylvania Compensation Rating and Inspection Bureau, who made available their records and extended much assistance and numerous courtesies during this study."

May 1, 1932

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

By J. R. Wait, D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the pre- dicted fields more nearly model the measured data than does the homogeneous half-space model.

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events. This is the second of two articles which report experts responses to questions about training for future mine emergencies. During the interviews they discussed how training should be conducted, who should be trained, and what topics should be included. This article will cover the third area: Topics that should be included in training for mine emergency response managers.

Jan 1, 1997

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

This chapter details the perspective from which collected data have been examined. The first part, intended primarily for lay readers, discusses several topics related to mining as an enterprise. Initially, the organizational functioning of atypical large mine will be described. It is the formal structure above a miner that decides the conditions of his or her work. A second point of concern is the technology itself An underground coal mine is a sociotechnical system, with workers and machines organized in particular ways during production. Third, general conditions and dangers underground will be described in detail. The physical environment of an operation is a powerful factor in the work life of miners. Fourth, a discussion of the process of formal training is given. During this training, a new worker is taught what the organization expects of him or her in the role of safe, productive, coal miner. Next, there are outside organizations that act as significant forces in the workplace. Examples include the Mine Safety and Health Administration (MSHA), State agencies, and the United Mine Workers of America (UMWA). The roles of these entities will also be examined. The second part of this chapter will depict each study site as a concrete setting, so that findings can be interpreted in their proper context. The Organizational and Technical Nature of Mining A coal mine is a complex system. It is defined as all parts of a mining plant's property (both underground and surface) that contribute, under one management, to the extraction or handling of coal [American Geological Institute 1997]. As suggested, many functions that must be carried out at an operation are only indirectly related to coal mining and processing. Even the jobs that are di¬rectly related tend to be numerous and varied [Wallwork 1981]. According to Palowitch [1982], the chief reason for this sophistication is that "after more than two centuries of exploiting our coal resources, today's coal industry finds itself saddled with a horrendous legacy of human impairments and environmental damages which society demands be corrected." Now, the effects of government regulation are evident in every aspect of the mining industry. Any operation, if it is to survive, must be administered with an eye for social efficiency and accountability. Long-range planning is needed to ensure that the mine produces coal in a cost-effective manner. One of the first things that must be considered is location and method of access. To extract coal from an underground mine, a coalbed (or "seam") must be reached from the surface. The term "portal" is generally given to any entrance that provides access to a coal mine. In hilly terrain, such as is found in Appalachia, the coal may "outcrop" on a hillside. This allows direct

Jan 1, 2000

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By M. L. Whisman

Several commercial processes for reclaiming used lubricating oil were duplicated on a laboratory bench scale. Laboratory tests were selected and in some instances modified to determine the physical properties of each oil produced. In addition, the hydrocarbon composition of some samples was determined using a liquid chromatographic technique, and compared with the composition of new oil in order to determine the severity of the re-refining technique. Selected samples of reprocessed oil were reformulated with an additive package for further estimates of quality as determined by wear, corrosion, foaming, and oxidation stability tests. Additionally, several samples of commercially re-refined oil and new oil were obtained and physical properties were determined for comparative studies.

Jan 1, 1974

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By Dennis R. Dolinar, Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mineworkers. Skin failures do not usually involve failure of the support systems, but result from rock or coal spalling from between the support elements. For instance, in 1997 more than 800 miners were injured by roof and rib falls, of which 98% were the result of skin failures [Bauer et al. 1999]. Also, nearly 80% of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and for roof and rib failures is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper reviews the roof and rib accident statistics resulting from skin failure, and highlights the incidences by type, numbers and percentage, in-mine location, supported and unsupported roof, and worker activity at the time of injury. Also discussed are the causes of roof and rib skin failures, current and improved support methods and materials for skin surface control, and machine design modifications for improved roof bolter operator protection. It also reviews the historical literature on skin failures and control methods.

Jan 10, 2000