Search Documents

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

By Leonard Obert

This report describes an inexpensive triaxial equipment for testing 2-1 / 8- , 4- , and 5-5 / 8 - inch - diameter rock cylinders subjected to loading conditions comparable to those encountered in underground mining . Only minimal specimen preparation is required . The maximum axial load that can be applied is 250,000 lb , which corresponds to an axial stress of 70,000 psi for the 2-1 /8- inch- diameter specimen . The maximum radial pressure that can be applied is the same for each specimen diameter ; namely , 10,000 psi . The mechanical parts in this equipment are relatively easy to machine and fabricate . The cost of all parts , including the 250,000- lb hydraulic press but not including labor costs , was approximately $ 1,000 .

Jan 1, 1963

By David K. Ingram

The development of large open surface fractures over mined-out coal longwall panels is the focus of this U.S. Bureau of Mines report. The research concentrates on defining the fractures characteristics and their controlling variables. The investigation was conducted at two mines in south-central West Virginia. All but one of the fractures are subparallel to the trend of the underlying longwall panel. One fracture is perpendicular to the trend of a longwall panel. Overall length of the fractures ranges from 60 to 900 ft. In cross section they are V-shaped, ranging from a couple of inches to 25 ft in width at the surface, but narrowing as they increase in depth. Fracture depth varies from a few inches to over 50 ft into bedrock. A vertical fracture or joint plane was observed in the bedrock at several open zones along the fractures. All of the fractures vary in elevation and do not parallel surface contours. The fractures are aligned with local joint trends, they correlate with longwall development, and they are situated in an increased tensional area over the mined out longwall panels. These observations indicate that the fractures are tensional openings along preexisting joint planes possibly triggered by longwall mining.

Jan 1, 1989

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966

By M. M. Tilman

The Federal Bureau of Mines developed a rolling method that improves creep resistance and yield strengths of lead alloys containing up to 5 wt-pct Sb. The 0.69-inch-thick slab-cast alloys were breakdown-rolled to 0.226 inch and finish-rolled to 0.063 inch at 5-or 20-pct reduction per pass. Rolling was at room temperature to simulate conventional cold rolling, and at 75°, 125°, and 175° C. Two alternative methods evaluated consisted of (1) a single cold final pass followed by annealing and (2) a single hot final pass. Two additional processing methods involving percipitation strengthening were included for comparison. Compared with conventional cold rolling, hot rolling at 125° and 175° C with multiple light passes vastly improves creep resistance and raises yield strengths. Tensile strengths are less affected. The other treatments also improve creep resistance significantly and generally improve tensile properties; magnitudes vary with treatment and composition.

Jan 1, 1975

By Sean Gallagher, Thomas G. Bobick, Diane M. Doyle-Coombs, Richard L. Unger

The U.S. Bureau of Mines has developed an in-house facility to evaluate selected effects of whole-body vibration (WBV) levels experienced by underground mobile equipment operators, Vertical vibration data were collected from a coal haulage vehicle via a uniaxial accelerometer attached to the machine frame under the operator&apos;s seat. Data were analyzed and processed so a computer-controlled platform could approximate the vibration signals. Eight men (35.5 yr 2 6.5 SD) participated in a pilot study to evaluate the effects of shock and kBV on heart rate (HR), blood pressure (BP), and subjective discomfort. Subjects were exposed to vibration for 30-min periods while seated in a typical seat (backrest angle at 90° or 130°) &apos;that was plain steel or modified with 2 in foam padding. Subjects repeated the same protocol on a separate day, without the vibration. Results indicated the vibration significantly increased the HR (Q< 0.01), systolic BP, mean BP, the number of times subjects reported discomfort, and overall subjective discomfort rating (pc 0.85). When seated in the steel seat, the overall discomfort rating (E< 0,081) ad the number of times discomfort was reported (p< 0.05) increased significantly. Seatback angle had no significant effect on any of the dependent measures.

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By L. D. Stewart

The main reasons for developing an induction system for signaling from the cage are, first, to increase safety, and second, to effect economies in the operation of cage and ship hoists, especially when work is being done in the shaft. To-day nearly all mines which employ safe methods have installed safety gates on cages, at the different levels, and at the collar of the shaft. Under the old system in some instances signals could only be Given from the station outside the cage, and in other cases, after the signal was given the only method whereby those riding on the cage could control its movements consisted of pulling the bell-rope hanging in the shaft, an uncertain and somewhat hazardous procedure at best. With the system herein described, however, it is possible, without opening the gates, to signal to the engineer from any place in the shaft whether or not the cage is moving, and finder the same conditions it is possible to converse with the engineer by using the telephone. In short, the cage tender has at all times an opportunity either to signal or talk to the engineer without leaving the cage.

Jan 1, 1931

By S. R. Wilson

[The Anniversary-Bucky pegmatite is one of the largest, dikes in the Quartz Creek district, 21 miles east of Gunnison, Colo. The major dike consists of quartz-albite pear pagmatite and graphic granite with many quartz masses as individual cores occurring within the dike. A mining operation on one of the largest core areas has exposed several mineralogic cones directly associate with the core. These zones, including the large- units of the dike, are quartz pegmatitc, quartz-perthite pegmatite, perthite pegmatite, muscovite-feldspar -quartz pegmatite, quartz-albite pegmatite, and perthite-quartz (graphic granite) pegmatite. Muscovite and beryl are found in the muscovite-feldspar-quartz zone and are the only two products that have been marketed. Other potential products are perthite, graphic granite, and possibly small quantities of columbite-tantalite, monazite, and related radioactive minerals. The Bureau of Mines drilled two diamond-drill holes during April 1950 to investigate the largest and cost promising core area. This, report describes the results of this drilling.]

Jan 1, 1953

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By H. Foster Bain

Ten years ago there was no general , country-wide service for the systematic training of miners in matters relating to safety . A beginning only had been made at a few scattered points . Under the old conditions each man was left largely to look out for himself in meeting the hazards of his day's work, and the foreman , shift bosses , and superintendents chiefly relied upon improvision when major accidents occurred . So long as the mines were small and the workers highly intelligent and well trained in routine mining methods , and when too , the pressure for output had not yet speeded up industry to the extent it has since those days , there was something to be said for this lais- sez faire attitude . When , however , the rapid expansion of industry lead to the introduction of new and little trained labor and to units of production of greatly increased size , the natural dangers of mining were greatly intensified . An accident in a small mine affects only a few; the same accident in a large mine , unless proper precautions have been taken , may cost the lives of many . The public does not generally recognize that the greatly increased outputs of the mines , of coal mines in particular , have been in recent years , obtained from substantially the same number of miners as ten years ago but with a personnel not nearly so well trained in mining . It is inevitable under : such conditions that more care must be devoted to avoiding accidents and much more elaborate preparations made for meeting them . In the years immediately preceding the establishment of the Bureau of Mines this speeding up of industry , change in the character of mine labor , and increasing hazard had all begun to be felt . Immediately prior to the organization of the Bureau of Mines , public attention had been drawn to a series of disastrous coal-mine explosions , to the increasing frequency of these disasters , and to the terrible loss of human life . resulting therefrom. One of the first problems , therefore ; confronting the Bureau was clearly that of finding methods of reducing the number of such disasters and lessening the severity of those that continued to occur . Toward this object were immediately directed the energies not only of the Bureau of Mines but also those of State mine inspectors , mine operators and various other agencies , all of whom were urged to cooperate in this great humanitarian work. The results of this work naturally cannot be measured by figures only . Work for increasing the health , safety , comfort , and happiness of human beings may not be gaged with mathematical precision . But certain features of this work as revealed by the record from year to year are of much interest . ”

Apr 1, 1921

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

By Richard F. Hewlett

The mining industry utilizes a vast store of knowledge, wisdom, and engineering talent in designing mining systems. However, the complexity of the required systems and the presence of numerous variables frequently necessitates raking important decisions without having adequate accurately detailed information. That many of the decisions made in the past were nearly correct, in the long run, is substantiated by the number of successful mining enterprises that exist in the world today. Subsequent to 1940, the disciplines of operations research and systems engineering were developed. The disciplines have produced methods of providing better information to persons responsible for making decisions.

Jan 1, 1963

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965