Search Documents

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By George H. Ashley

Character The bituminous coals of Pennsylvania range from low volatile to high volatile, but are all low moisture coals The coals are of three types caking of coking, noncaking or splint, and cannel The percentage of volatile matter in all kinds changes from low at the east to high at the west This change is thought to be due to the pies sure and folding to which the coals along with the other rocks have been subjected In the Broad Top field, and in Somerset, Cambric, Clearfield, Centre, and other counties to the northeast, most coals contain from 3 to 5 times as much fixed carbon as volatile matter, the fixed carbon ranging from 67 to 75 per cent, and the volatile mattes from 16 to 24 per cent These coals are classed as lovol coals In the line of counties just west of those listed the coals are of the medium volatile class (midvols) This includes the famous Connellsville coking coal Still farther west, covering most of Washing ton and Westmoreland counties, and the counties to the north of them are high volatile coals of gas coals (hivols) This is discussed in Part I on the geology of the coals of Pennsylvania, where is given in isocaib map Cannel coals ale found in many par is of the bituminous coal field of Pennsylvania, but in particular in Beaver Butler, Armstrong, Indiana, and Clear field counties The cannels of Beaver and Butler. counties are typical high volatile cannels, many of which have been used in times past for oil distillation The cannels of Armstrong and Indiana counties are medium volatile cannels, and while main taming the physical character of cannels, have no more volatile neat ten than the coals around them The cannels of Clearfield County tie low volatile Splint coals of noncakmg coals are not abundant in Pennsylvania. The Sharon coal, formerly mined in Mercer County, was a noncaking or splint or block coal, and was formerly used in the raw state in non smelting Uses STEAM COAL Practically all of the coals of Pennsylvania are steam coals, though many coals in the Commonwealth, because of high ash, are not good steam coals The coal of the Pittsburgh district has long been famous

Jan 1, 1928

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

On a continuous miner coal face methane concentrations are affected by the quantity of fresh intake air reaching the face. When mining the box cut on a 12.2-m (40-ft) two-pass extended cut face, the continuous miner is always at the point of deepest penetration, and operation of the machine-mounted dust scrubber and water spray system improve the flow of fresh air to the end of the box cut. However, when the continuous miner leaves the box cut to begin cutting the 40-ft slab, little is known about how much ventilation air reaches the end of the box cut. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health conducted a full-scale study to answer this question. Tests were run to determine how much ventilation air reaches the end of the box cut with the continuous miner at three locations in the 40-fttwo-pass extended cut mining sequence; at the end of the 40-ft box cut, at the start of the 40-ft slab cut, and 6.1 m (20 ft) into the slab cut. During these tests, methane gas was uniformly released at the end of the 40-ft box cut. Methane concentrations measured0.3 m (1 ft) from the roof and face of the box cut were used to estimate face airflow quantities. Fresh air flow rates of 1.89and 4.72 m/sec (4,000 and 10.000 cfm), scrubber flow rates of 0, 4,000 and 10,000 cfm, water spray pressures of 0 and3827 kPa (0 and 120 psi), and a blowing curtain setback position of 15.2m (50 ft) were used during these tests. To improve ventilation to the end of the 40-ft box cut when the continuous miner was starting the 40-ft slab cut and 20 ft into the slab cut, the blowing curtain was advanced from its 50-ft setback to locations 40-ft and then 8.5 m (28 ft) from the face. KEYWORDS: Face ventilation, Extended cut, Methane, Box cut, Continuous miner, Scrubber

"Health standards in the U.S. are among the highest in the world. Achieving these standards have often had an impact on productivity, slowing output, and raising prices to levels that make it difficult to compete with many foreign industries. The answer to many of these problems lies in the development of new and advanced control techniques. This overview has identified some of the major respirable dust technological hurdles that have been overcome, and provided some insight into current and future approaches underway to remove these obstacles and to provide the United States with the most advanced state-of-the-art mining industry in the world from a respirable dust standpoint. The necessary developmental research is costly and time-consuming. The long-term, high-risk aspects of this effort are being addressed by the Bureau and the Generic Center on Respirable Dust, with support by industry. This should be recognized as one of the principal agents through which the great mineral potential of this Nation can be realized, and our international status as a mining power be assured without compromising the health and welfare of those who ensure it.The problem of more stringent dust standards will continue to grow. To date, approximately 40 pct of the coal mining industry has been placed on more stringent dust standards due to quartz. Control techniques must be improved if mandated levels are to be met. As longwall production increases, dust levels will also increase. In light of the industry trend toward longwall mining, if no new control technology is available, the Federal dust standard will act as a constraint on future output per hour. The Bureau has recently completed a survey of 18 coal preparation plants; 50 pct of these operate at dust levels which exceed 2.0 mg/m3; future work will be directed toward solutions in this area. The 2.0 mg standard for respirable dust is for dust particles which are below 10 pm in diameter. Recent studies have shown that dust in the range between 10 and 25 pm can cause obstructive airway disease. The Bureau is currently determining the extent of exposure to dust in this size range from various mining operations."

Nov 1, 1988

By A. C. Fieldner

It is estimated that 6,202,235,000 gallons .of- gasoline was produced during the year 1922. The crude light oil- output Burin- the same year is estimated at 111,000,000 gallons, or 1.8 per cent of the gasoline production. In fact, if all the coal mined were coked in by-product ovens, and the light oil recovered therefrom, this product would amount to only 15 to 20 per cent of the quantity of the petroleum gasoline now produced annually. It is obvious therefore, from these figures that the light oils by present coking processes can not assume great importance as a gasoline substitute in a national sense. However, the use of light oil as a motor fuel is of real importance in districts adjacent to by-product coking operations from which a reasonable proportion of the local motor fuel supply may be derived. The certainty of diminution of petroleum resources in the relatively near future demands the utmost utilization of gasoline substitutes from the distillation of coal as well as other sources. Motor benzol is a by-product from the destructive distillation of coal. From 11/2 to 3 gallons of refined motor benzol is obtained per ton of coal carbonized. The light oil vapors are extracted from the by-product coke-oven gas by passing it upward through a series of towers in which these vapors are absorbed in a descending current of "wash" oil (petroleum distillate). The light, oil is recovered from this wash oil by distillation with live steam, the resulting crude light oil consisting of a mixture of benzol, toluol, xylol, solvent naphtha, and a small amount of other substances (unsaturated hydro-carbons, carbon disulphide, and other sulphur compounds, phenols and pyridines) is then transferred to an intermittent still and fractionated into crude motor benzol, which includes the toluol and a part of the xylol or light solvent naphtha. The crude, motor benzol is yellow in color, contains sulphur compounds which corrode copper and brass, and also contains unsaturated bodies which oxidize and polymerize on standing, producing sediment and forming gummy deposits highly objectionable when the benzol is used in motors. These objectionable

Jan 1, 1923

By Van H. Manning

EXPLOSIVES RESEARCH. As the physical laboratories of the explosives section of the Pitts- burgh experiment station were equipped for testing the physical properties of explosives, both the Army and Navy Departments for many years had requested the Bureau of Mines to make such tests. Chemical control of the physical tests through analyses, heat tests, analyses of gaseous products of combustion, and sand tests was exer- cised through the explosives chemical laboratory. Often an investigation was cooperative between two laboratories. The explosives chemical laboratory also aided the work of the Ex- plosives Regulation both by chemical tests and investigation of acci- dents in explosives plants. COOPERATIVE WORK FOR ARMY AND NAVY DEPARTMENTS. The explosives chemical laboratory devised, at the request of the Bureau of Ordnance of the Navy, a more economical method of making hexanitrodiphenylamine. This problem was assigned to the Bureau of Mines by Dr. C. E. Munroe, chairman of the committee on explosives of the National Research Council, acting as the depart- ment of science and research of the Council of National Defense. Before the United States entered the war the following reports of investigations were submitted to the Army or the Navy: 1. Report of sensitiveness and relative efficiency of TNT and ammonium picrate, dated February 6, 1913, undertaken at the re- quest of the Chief of Ordnance. 2. Report of tests and examination of two samples of TNT and one of TNA for the Ordnance Department of the Army, dated August 5, 1915, was undertaken at the request of commanding officer, Frankford Arsenal. 3. Report of tests for sensitiveness to detonation of mercury ful- minate of 21 samples of TNT crystallized from various solvents, for the Bureau of Ordnance, Navy Department, dated June 17, 1916. 4. Report of tests of two samples of mercury fulminate for Frank- ford Arsenal, dated December 2, 1916, undertaken at the request of the commanding officer, Frankford Arsenal. After the United States entered the war the following reports of investigations were submitted: 5. Report of pendulum friction and large impact tests on two samples of "sodatol" and two samples of "amatol." The final report was dated July 20, 1918; and the preliminary report, May 15, 1918. This investigation was undertaken at the request of the Ordnance

Jan 1, 1919

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By C. P. Bowie

"It is well known by all who are familiar with the oil industry in America that the oil pipe line is as fundamentally a part of this industry as the railroad is of most other American industries. The oil pipe line was first introduced about 56 years ago, and since that time has so demonstrated its superiority as a means of carrying crude oil froze the well to the refinery, that this method of transportation has largely superseded all others. This has made possible the building of refineries in or near the large consuming centers, rather than at the wells, which are usually remote from the centers of population.The pipes for conveying the oil are laid on the surface of the ground, or at a depth varying from 18 inches to 3 feet beneath the surface, and the main lines are generally eight inches in diameter. The oil is forced through the pipes by means of pumps operated either by steam or by internal combustion engines. The pump stations are located from 1 1/2 to 90 miles apart, varying with the condition of the country through which the pipe lines extend, and the viscosity of the oil to be handled.Some of the larger pipe-line systems and hundreds of miles in length. It is estimated by the U. S. Geological Survey that the total mileage of oil trunk lines in the United States today is approximately 34,000, and that the gathering systems, which are a fundamental part of the trunk systems, aggregate about 11,500 miles in length, making a total of 45,500 miles.Using those figures as a basis, some general conclusions as to the investment represented will be made. At the time most of the lines were constructed, the average cost per mile based on eight-inch pipe was about $6,500. The cost of the average pump station at that time varied from $130,000 to $250,000. The cost at the present time, on account of the increase in price of labor and materials, would be much in excess of these figures. The fixed investment in pipe lines is, therefore, very extensive. It corresponds closely with the actual cost of the property, and is estimated to be approximately $500,000,000."

Sep 1, 1920

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

Objective Develop a method to warn of hazardous conditions and enhance safety during operation and inspection of vertical mine shafts and hoists. Background Mine hoisting is the most critical and potentially the most dan¬gerous operation in underground mining. Many hazards are related to falls of miners and materials, ground instability, and malfunction or lack of safety devices. All have the potential to cause a cata¬strophic accident. A condition known as "slack rope" is particularly dangerous, expecially if it occurs without the operator's awareness. The most common occurrence of slack rope is in metal or nonmetal mines that have a history of ground control problems near the "haft. Approach Studies of hoist safety features and Mine Safely a and Heath Administration (MSHA) accident statistics suggests a need to measure wire rope tension, conveyance speed and position, and shaft guide misalignment. The most accurate data are obtained directly from the conveyance. Such data could warn of potentially dangerous situations during hoisting operations, as well as during inspections, maintenance, and lowering of large equipment. Figure I shows the concept for monitoring wire rope tension, conveyance position, and guide displacement. Progress to Date A conveyance-mounted system has been developed that monitors rope tension: hoist conveyance position, speed, and load; and shaft guide misalignment. A "flex-beam" load sensor mounted just above the- conveyance protects against slack and tight rope. The measurements are transmitted 60 times a second via wireless equipment from the conveyance to the hoist room. An encoder mounted on the conveyance eliminates the need to correct the position because of rope stretch. Figure 2 shows the encoder wheel and guide displacement sensors being mounted on a cage in¬spection deck. A potentiometer monitors misalignment of the shaft guides during inspections. Information about the cage or skip can be acquired by the shaft inspector using a hand-held indicator. Inspection can also he conducted remotely from a station or hoist room using the wireless link to a laptop computer. Figure 3 shows test results from a simulated slack rope condition. Patent Status NIOSH has a patent pending on this device entitled "Cable-Load¬Sensing Device." For More Information NIOSH is seeking cooperators to assist in further tests of this technology to improve hoisting safety. Additional information can he obtained by contacting Michael J. Beus, Steven Iverson, or Elaine Cullen, Technology Transfer Officer, NIOSH, Spokane Research Laboratory, Spokane, WA 99207 at (509) 354-8000.

Feb 1, 1998

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By Maria I. De Rosa

For all coal mining categories, data on coal mine fires during 1990-1999 have been reported as actual numbers and calculated values. 1. For each mining category, actual numbers include the total number of fires, fire injuries, employees' working hours, lost workdays, and coal production (for underground and surface mines only) for a 1 0-year period (1 990- 1999) and for five successive 2-year periods with the 10-year period. These numbers have also been reported by state ( 10-year period). The actual number of fire fatalities has been reported by time period. Furthermore, actual numbers of fires for the five 2-year periods have been reported by ignition source, method of detection and suppression, equipment involved, location, and burning material. Actual numbers of fire injuries per number of fires causing injuries and total fires have been reported by year, ignition source, equipment involved, and location. 2. For each mining category, the calculated values include the fire and injury risk rates during the 10-year period and the five 2-year periods. The fire risk rate (Frr) values were calculated according to the USBM formula [Pornroy and Carigiet 19951. The injury risk rate (Irr) values were calculated according to the MSHA formula [MSHA 1991a, 1992, 1993, 1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. Also, risk rate values for individual states (10-year period) were calculated according to the above-mentioned formulas. Of note is that only the risk rate values for the 10-year and five 2-year periods and risk rate values for individual states with the highest number of fires and fue injuries were considered for comparison purposes. The fatality risk rate values were not calculated because of the extremely small number of fire fatalities during the 1 0-year period. 3. Calculations of risk rate values are as follows: a. Fire risk rate (Frr) value: Number of fires per million tons of coal produced [Pornroy and Carigiet 19951. b. Injury risk rate (Irr) value: Number of fire injuries multiplied by 200,000 working hours per total employees' working hours [MSHA 1991a, l992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. The Irr value is the average risk rate value for the number of fire injuries per 200,000 working hours for a given time period.

Jan 1, 2004

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.

Mining and reclamation procedures that meet the requirements of SMCRA are illustrated on pages 8 and 9 for each of the three major surface coal mining methods -- area mining, contour mining, and mountaintop removal mining. The three methods involve the same basic steps: clearing the land of trees and other vegetation, removing topsoil and overburden, mining the coal, and reclaiming the land. Although all three methods would not usually occur on any single site, the illustration facilitates comparison of mining and reclamation methods and aids basic understanding of the reclamation processes that take place under SMCRA. Area Mining The area mining method is commonly used to mine coal in the flat to moderately rolling terrain found principally in the western and midwestern states. After the overburden is excavated down to a coal seam, the mining area is enlarged horizontally to expose more coal for removal. In the West, where coal seams are commonly 10 to 20 feet thick (and range up to 100 feet thick in the Powder River Basin of Wyoming), the life of some mines maybe more than 50 years. In the Midwest, coal seams are typically 3 to 7 feet thick and 75 to 100 feet below the surface. Because of the large expanse of area mines and their relatively unrestricted sites, enormous equipment is used to remove overburden and reconstruct the land. The area mining operation in the illustration is on land that was formerly used for farming. The drawing shows that the agricultural use is being reestablished immediately following reclamation. Mining is proceeding across the land toward the left side of the site. The initial excavation was made far enough away from the stream along the right edge of the site to prevent damage to the water supply. The coal under most of the site has been removed, and reclamation has been completed on some of the land. For example, some of the cattle in the foreground and those in the feedlot behind the silo are grazing on reclaimed land that has been mined. At the far left of the illustration, topsoil from the unmined area is being removed by scrapers, transported across the area of active mining, and immediately spread on the land on the right, which is being reclaimed. (Reclamation of mined land as soon as practical, as required by the Act, is called contemporaneous reclamation.) A

Jan 1, 1992

By Linda L. Chasko, Ronald S. Conti, John D. Cool

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion, roof fall or water innundation. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted, and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety and several mining companies. The exercises were conducted at NIOSH’s Lake Lynn Laboratory and operating mines during 1995 to 1999 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included various chemical light shapes and laser pointers to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escapeways and marking crosscuts, and thermal imaging systems to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. Anew team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 400-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” administered first aid, mapped the passageways, built temporary stoppings, and ventilated the smoke-filled entries. Advanced training included the extinguishment of a conveyor belt fire in a surface fire gallery. Two teams, each carrying charged waterlines, were escorted into the fire gallery through both doors. These teams controlled the rollback smoke and extinguished 7 to 9-m of burning conveyor belt. Team members indicated that the exercises were extremely beneficial due to the realism of thetraining simulations.

By Scott Turner

The settlers of a new country necessarily suffer at first from the lack of accumulated stocks of metals - in-use that are possessed in older countries . Our American colonists were at first compelled to import their metals in manufactured forms , and it must have proved difficult to produce an exportable surplus of commodities with which to pay for them . These circumstances stimulated a search for domestic ore deposits . Various discoveries resulted , so that as early as 1628 , we find the colonists importing two craftsmen from England to establish iron -works in Massachusetts to beneficiate local ores . In 1648 , an iron -works at Lynn was producing metal at an annual rate of 400 tons . Later on , the colonial iron industries became of importance , some metal being actually exported to England . The people of this country thus early became convinced of the necessity for domestic mineral production . It is now little realized how persistent were their efforts to - make mineral discoveries , before the gold- rush to California ; the extraordinary success of our subsequent mineral explorations has overshadowed the earlier record . Precise and complete accounting of our mineral production , having the character of national bookkeeping , is available only for the series of years beginning with 1880 , when commences the official record that is provided by the Government publication called Mineral Resources of the United States . In the period of 52 years , from 1880 through 1932 , the value of mineral production of the United States amounted to more than 122 billion dollars . Only 12 billions of this total were produced in the 21 years , 1880-1900 , while nearly 110 billions were produced in the first 31 years of the present century . Of this 110 billions , over 53 billions were produced in the most recent decade , 1921- 1930 , the production of the previous decade , 1911-1920 , having been only 37 billions , though it included the war period ; that of the decade 1901-1910 was 16 billions . In 1931 , the total value of mineral products of the United States was $ 3,180,000,000 , compared with an average annual value of $ 5,556,000,000 during the previous five - year period , 1926-1930 . The decline in 1931 from that average was therefore 43 per cent . As to the three great groups of mineral commodities , metals fared worst , with a decline of 55 per cent in the value of their production , while the value of fuels declined 39 per cent , as did that of the nonmetals group .

Jan 1, 1933

This chapter explores leadership behavior in a life-threatening situation-fire in a coal mine. Previous chapters have discussed the database of interviews with miners who escaped from underground fires. Researchers raised questions such as: (1) Who led the miners out of the mine? (2) Did leadership make a difference in the escapes? (3) Was the escape leader the hierarchal leader? (4) What, if any, characteristics did the escape leaders possess? Subsequently, researchers analyzed the mine fire database from a group interaction perspective to address the leadership questions posed. Leadership has been one of the most researched topics of human behavior in the twentieth century. Studies have ranged from individual characteristics of leaders, to situational leadership, to interaction of leader and follower, suggesting different leadership techniques for different followers. The question that emerges here is: Are there different types of leadership that "fit" different kinds of situations? In a crisis situation like that examined in the present study, such information about leadership may significantly improve the chances of escape. To address these issues, the study team looked at the formal authority structure before each fire, considered leadership behavior or lack of leadership during the escapes, and examined those conditions associated with the emergence of leadership. According to Bardo [ 1978], "Emergent behaviors are those forms of action, and the norms, values and beliefs governing those actions, that rise out of the disaster situation." This chapter discusses previous studies in the area of crisis leadership and examines the emergent behaviors of leaders under duress during the mine fire escapes. Previous Studies The research on leadership during emergency situations has consisted mainly of simulation and field studies, with the principal concern being escape from building fires. During the 1980s, Hayashi [1988] created a computer simulation model to evaluate leader behavior in a fire. Although his purpose was to aid in planning for disaster prevention, his findings are relevant because they address the issue of situational leadership in crisis-where a leader changes his or her behavior to fit the situation. Essentially, his simulation model was designed to judge the actions and thinking of leaders. The simulation was tried by 101 subject/leaders 4 times each. The simulation consisted of amaze containing the leader, an informal leader, and 50 evacuees. Interestingly, the results indicated that the leader's actions were not dictated by circumstances. Any differences in behavior were attributed to the individual characteristics of each leader. The study also showed that the worse the situation became, the less individual

Jan 1, 2000

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974