Search Documents

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

By Wilbur I. Duvall, Thomas C. Atchison, David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain en- ergy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy E/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form Analysis of the data showed that the intercept parameter H depended upon the type of explosive used but that the absorption coefficient B was practi- cally independent of the type of explosive. Comparison of the intercept pa- rameter H and the calculated energy of the explosive showed that the percent- age of explosive energy transferred to the rock increased linearly as the ratio of the characteristic impedance (product of density and propagation velocity) of the explosive to that of the rock increased toward unity. From 5 to 9 percent of the calculated total energy released by the explosive was transferred to the rock as radial strain energy.

Dec 1, 1959

By Charles E. Munroe

On March 14, 1921, an explosion occurred at about 6:15 A.~. on the premises of an iron-mining concern throug:1 which two magazines, one containing upwards of 9,000 pounds ot a high explosive of the dynamite class, and a second, 60 feet distant, containing upwards of 10,000 No. 6 detonators, were completely destroyed, and a ncratertt,? f3et deep by 30 feet in diameter, was excavated in the gro~ at ~he place whare the mag~iine containing the high explosive had been lo~ated. As a rule any eye wit~esses to the circumstances im.~ediataly preceding and d(irectly concurrent with a.c.ci.:lental ex;losions ar.e victims of s11ch explosions, and, therefore, the conclusions reached as to the cauoa. of such explosions must, perf'orce, be based aln:ost completely on circumstantial evidetJ.ce. In this iii.stance, b:ecause both the explosive and detonators were of -orov{:;d: character; because of the time of the day and the state of operations iit the·· time of the e:.q,losion; because the rerroteness of the location of the n:-1agazi::1es 1 0::1 the side of a ravine, easily admittfi of unobserved approach; beca:iise differencas existed, and because no obvious cause was at once apparent, there arose suspicfon that the explosion was not accidental.

Sep 1, 1921

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

By E. J. Gleim

"When permissible equipment is first placed in a gassy mine, those in charge may not realize the amount of attention and care they must give it if they intend to secure its full value as safety equipment. If permissible machines are installed as a safety measure, then they must receive regular, intelligent inspection and upkeep to forestall the development of unsafe features.Certain fundamentals have been followed in the design of this type of equipment in order to minimize the possibility of its igniting gas and dust. Hence, some knowledge of these fundamentals is essential to the inspector or official charged with the duty of ascertaining the condition of permissible machines with respect to safety. Familiarity with the constructional details of a machine is of first importance in making a thorough inspection of it. A knowledge of Schedule 2C3 which gives the requirements for practically all types of motor operated equipment receiving the United States Bureau of Mines' approval is also a requisite.There are certain special features in the construction followed by different manufacturers that can not be made clear for the purposes of inspection except by a lengthy description which would be inappropriate in this paper. There are, however, some general points that are applicable to the inspection of any machine employing trailing cable for connection to the power supply, also some that apply to any permissible storage-battery locomotive.The following list, based on the writer's experience in making field inspections, gives these general points in the form of questions which may he used as a guide by the inspector. A brief explanation is given after each question so that the reason for checking up on each point will be understood.1. Is a U. S. Bureau of Mines' approval plate attached to the machine? (Such a plate is necessary in order to establish identification as a permissible machine.)2. Is approval plate clean?(The plate should be clean so that the precautions enumerated on it are readable.)3. Is trailing cable protected by a fuse or other automatic circuit-interrupting device?(Trailing cable must have a fused trolley tap or other suitable means for short-circuit protection in case the cable is run over or splices fail. Proper fusing will minimize the possibility of fire in the cable reel.)4. If a trolley tap is used, does it contain a fuse of the proper capacity? (A piece of trolley wire or, too large a fuse may entirely defeat the purpose of fusing.)5. If a fused trolley tap is not used, how is connection made to the power supply? (The end of the trailing cable must be fitted with an insulated arrangement to minimize shock hazard when connecting the cable to the power supply.)6. Are the main fuses (or overload relays) of the correct size (or setting) for protection of the machine against overload?(Too large a fuse or too high a setting of the overload relay will permit damage to the machine by abuse through sustained overloads.)7. If the machine has a headlight, does the headlight circuit have overload and short-circuit protection?(The wiring of the headlight circuit on a machine is usually of a smaller size than that for the main circuits and therefore requires fuse protection proportionate to the size of wire.) Note: This same question may be asked relative to coal drills sometimes mounted on a machine."

Apr 1, 1932

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By Thomas J. Peters

This report is part of the U.S. Bureau of Mines Idaho Land Assesment Program to study the mineral resources of priority roadless areas in Idaho. The results of these mineral inventories provide minerals information needed to make wise decisions regarding future land management practices, and to ensure a dependable supply of minerals at a reasonable cost. The 16,300-acre Lionhead area, studied in 1991, lies along the Montana border north of Henrys lake, 10 mi west of West Yellowstone, Montana. The study area includes much of the rugged Henrys Lake Mountains, and is largely covered with conifer forest. Several peaks are over 10,000 ft in elevation. The Lionhead area has been proposed for Wilderness. No mineral resources were identified within or near the Lionhead study area. Five prospects occur in, or within 1 mi of the area: these include 1) an intermittently used road gravel pit, 2) the Thimbleberry lateritic iron prospect, of geologic and historic interest only, 3) the Tick Heaven talc prospect, 4) the Dry Fork garnet prospect, and 5) the lynx prospect, which appears to be of historic interest only. Talc is seen only as float at the Tick Heaven prospect, but the geology is permissive of talc resources at depth. The garnet prospect, and nearby similar alluvial terrane, mainly outside the study area, appears to be the most likely setting to contain mineable resources. Examined workings include four trenches and pits in rock and one gravel pit.

Jan 1, 1992

By R. H. Lien

The Bureau of Mines, U.S. Department of the Interior, has developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. This process, known as the citrate process, involves absorption of sulfur dioxide (SO2) in a buffered solution of citric acid. The S02-loaded solution is regenerated by reaction of the S02 with hydrogen sulfide (H2S) to form elemental sulfur. As an adjunct to the citrate process, bench-scale research has shown that S02-loaded citrate or glycolate solutions can be regenerated by countercurrent contact with steam (stripping) in packed towers. Concentrated S02 is produced by condensing the steam from the stripper product. Thus, steam stripping provides strong S02 gas for liquefaction, sulfuric acid production, or reduction to elemental sulfur. Stripping steam requirements were determined for treatment of 0.25-, 0.50-3 1.0-, and 2.0-pct-S02 waste gases. Steam requirements decreased with increasing S02 concentration n the simulated waste gases. For example, 5 grams of steam per gram o S02 was required to remove 90 pct of the S02 from a simulated copper smelter gas (2.0 pct S02), while 30 grams of steam per gram of S02 was needed for 90 pct S02 removal from a simulated coal-fired powerplant gas (0.25 pct S02).

Jan 1, 1979

Rank the dust knockdown (airborne capture) ability of six different types of water spray nozzles, Approach A fixed quantity of dust is released into a large, closed chamber in a laboratory. Water sprays are turned on inside the chamber and their effectiveness on the dust cloud is evaluated from the rate at which the dust disappears. This method better simulates dust suppression underground than methods tried earlier. The results of the laboratory test were confirmed by conducting tests on a full-scale mod-el continuous miner face where dust levels were measured in the return airway. Results of the Closed Chamber Tests The graph indicates that atomizing nozzles provide the best use of water for dust scrubbing. However, use of these nozzles is limited by their susceptibility to damage and clogging. Hollow-cone nozzles perform almost as well as atomizing nozzles. Test results also indicate that full-cone, venturi-assisted, and flat-fan spray cones are about two-thirds as effective as hollow-cone nozzles. The least effective were venturi nozzles designed for moving air. The most significant advantage of hollow-cone nozzles over other nozzles tested is reduced clogging due to larger orifice size. The hollow-cone nozzle used in the test and depicted by the graph was type BD-3 manufactured by Spraying Systems Co., Wheaton, IL. This nozzle is already used on many continuous miners. Other hollow-cone nozzles of

Jan 1, 1982

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

By C. N. Schuette

"The production of silica and magnesia crucibles in the induction furnace was attempted and achieved in the laboratory of the Pacific Experiment Station of the United States Bureau of Mines. This work was undertaken at the request of other stations for laboratory crucibles of a certain specified wall thickness and capacity.The essential new parts of this work are the development of a technique for the high-frequency furnace production of silica crucibles of greater wall thickness than could be readily fabricated from commercial fused silica, and for heavy-walled magnesia. crucibles of great density and mechanical strength. A considerable bode of patent literature on the Production of fused silica ware in resistor-type furnaces was examined, but it furnished no significant help for the present problem. Similarly sintered magnesia refractories are often made for technical purposes, but for use at temperatures of 2000o C. or over, the material must be sintered at higher temperatures than can be attained by combustion firing, and the very great shrinkage encountered at these temperatures requires special methods. Small crucibles. of magnesia fused in the electric arc have been made by Tritton and Hansen,3 but the practical size of such containers is very limited.Many different methods of making crucibles in the induction furnace were tried before satisfactory results were obtained. The following description covers only the most satisfactory method, which produced crucibles of excellent quality in a reasonable time and with a moderate expenditure of power and materials."

Oct 1, 1929

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By V. P. Bhavanandan

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. Trachea removed from pathogen-free rats were maintained as organ cultures and used to study the effects of coal dust exposure on the synthesis of mucin. The high molecular weight isotopically labeled (3H-glucosamine, 14Cleucine or 35S-sulfate) mucin could be purified by gel filtration, treatment with testicular hyaluronidase, ion exchange chromatography, delipidation and CsBr density gradient centrifugation. To examine effect of coal dust on mucin production, groups of explant cultures were exposed to media containing coal dust at 100 µg per ml every 2 days for 2 weeks while control cultures were treated with media without dust. Analysis of the spent culture media showed that treatment with dust markedly decreased the production of nondialysable glycoproteins as well as hyaluronidase-resistant acid-precipitable fraction consisting mainly of mucin. Since the synthesis of protein was not affected to the same extent the decrease in mucin production is not entirely due to cell death. In separate experiments rats were subjected to in vivo coal dust exposure in inhalation chambers and tracheae of these and control rats were removed for explant cultures. The incorporation of precursor isotopes into mucin by these explant cultures are being examined. (Supported by U.S. Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust under grant G1135142, project 4210).

Jan 1, 1988

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

BIBLIOGRAPHY 1. Dougherty, John J. , "Control of Mine Fires", Publication of the Mining Extension Service, School of Mines, Appalachian Center, West Virginia University (1969). 2. Coal Age, "Fire, Explosions and Recovery, Federal No. 1 Mine", November, 1963. 3. Nagy, et al., "Sealing a Coal Mine Passage through a -Nor-ii-hole: A Progress Report", U.S. B. M. Publication No. 6453, (1964). 4. Murphy, et al., "Use of Fly Ash for Remote Filling of Underground Cavities and Passageways", U.S. B. M. Publication No. 7214, (1968). 5. Pennsylvania Drilling Company, Pittsburgh, Pennsylvania. Personal Review of Equipment. 6. Industrial Hazards and Communication, Division of U. S. B. M. Personal Communication with John Murphy and Merle Bowser. 7. Instrument Technology, Inc., Borescopes and CCTV Systems for Inspections of Nuclear Reactors; Personal Communication. 8. "Public Works", July, 1972. 9. The Industrial Hazards and Communications Division of the U.S. B. M. , Personal Communication regarding Cohu Model No. 2006. 10. "Bibliography on Underwater Photography and Photogrammetry", Eastman Kodak Pamphlet No. P-124. 11. Optical Properties and Visual Effects of Smoke-Stack Plumes, U.S. Department of HEW, 1967. 12. Middleton, W. E. K. , "Vision Thru the Atmosphere", Univ. of Toronto Press, 1952. 13. Kodak "High Speed Infra Red" film and Singer Corporation Model TI Silicon Vidicon TV Camera. 14. Night Vision Laboratory, Fort Belvoir, Maryland; Barnes Engineering Company, Stamford, Connecticut, Model, T-101; AGA Inc. , Secaucus, New Jersey, Model, "Thermovision" 680.

Jan 1, 1973