Search Documents

By L. T. MCELVENNY, Robert B. McElwaine, M. Clair Smith

Production of mercury from the cinnabar deposits of the southwestern Arkansas mercury district began in 1931 , reached its peak in 1942 , and ended in 1944. The mines are now idle . Virtually all the cinnabar was obtained from deposits in a belt , about a mile wide , of steeply dipping sandstone beds in the overriding blocks of three thrust faults . The belt was productive for a length of about 27 miles eastward from eastern Howard County, through Pike County, into Clark County . During the early life of the district, Federal agencies watched and recorded its progress as a contributor of a strategic metal, and later, during the war, conducted investigations designed to advance its development . In 1941 , the Bureau of Mines and the U. S. Geological Survey cooperated in investigations on eight mineralized areas in the western part of the district , to wit : Hales mine , U. S. mine , Lulu Bell property, Hopkins Hill , East Gap Ridge , Gap Ridge , Parnell Hill , and Section 17 mine area . U. S. Geological Survey prepared both surface and mine maps and designated the areas to be investigated ; the Bureau did the drilling , trenching, and sampling involved in the investigations . Twelve holes , aggregating 3,539 feet of bore , were diamond drilled on six properties ; 5,309 linear feet of surface trenches were bulldozed in six areas and 19 samples taken from them ; and 86 underground channel samples were cut in two adits on one property . In 1944 , the Bureau of Mines measured mine dumps and calcine dumps in the district in an investigation of their mercury content . Two mine dumps and one calcine dump were sampled . The data pertinent to the work done by the Bureau are included in this report .

Oct 1, 1950

By D. Harrington, B. W. Dyer

"Two recent occurrences in Western metal mines in each of which 3 men were killed due to breathing fumes from explosives, have aroused keen interest among mining men not only as to the exact cause of such accidents, but also as to possible preventive measures.In sinking the forty five degree incline Marsh *haft near Burke, Idaho, on May 13, 1920, a round of holes containing about sixty pounds of 40 per cent gelatin explosive was blasted by the night shift upon leaving at 11:30 P.M. It was customary for the night shift to leave compressed air blowers open at bottom of abaft until the compressor was shut down slightly before midnight. Presumably this was not done on the night of the lath as the fumes were so heavy in the shaft bottom on the morning of the 14th that at about 8 o'clock, Superintendent Bergen and one of the shaft men, on reaching the shaft bottom, were overcome and fell from the bucket into the sump containing about six feet of water; and when two other men went down in the bucket a few minutes later to investigate, one also fell into the sump and the other was barely able to roach the shaft collar. The three bodies were later on recovered from the sump.At 400 P.M., June 10, 1920, at the Dominion Mine, Colville, Washington, a round of 11 holes containing about fifteen pounds of 60 per cent nitro¬glycerine explosive was blasted in a fifty degree raise about fifty feet above the main tunnel level by the shift going off for the night. in this mine it was the practice not to try to blow out the fumes until just before the shift went to work the next morning, Although no work was being done on the night shift, one of the raise men, curious to ascertain the effect of the shots, about 7:45 P.M., wandered into the mine (which was a tunnel only a few hundred feet in length), and was missed by one of his companions about an hour later. When three men tried to remove the body of the inquisitive miner, two of them were also overcome; ultimately these two and the first man were removed from the point at which all were asphyxiated, which was practically at the foot of themaise."

Jul 1, 1920

By G. S. Rice

[This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail ira bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite to it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion Of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of exclusive mixture, was at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 foot and an upper layer of coal 2 1/2 feet thick had been removed, the recess so made would save a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in this volume to produce this 9 per cent explosive mixture.]

Jan 1, 1930

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By J. W. Miller

From 1889, when the first railroad shipments of coal were made from McDowell County, W. Va., until today, the coals produced from the New River and Pocahontas groups have had a good reputation as premium low-volatile coals. Although there has been a large production from the Pocahontas No. 3 and. Pocahontas No. 4 beds, considerable reserves remain. This Bureau of Mines publication is one of a series appraising the Nation's coking-coal reserves by presenting data on the basis of which the practicability of upgrading marginal deposits to metallurgical standards can be determined. This study of the preparation characteristics of McDowell County coals is the second of the series to be undertaken in West Virginia. The Pocahontas No. 3 and No, 4 beds have not been included because their washing characteristics are well known.

Jan 1, 1954

By R. L. Schmidt

Research conducted over the past 20 years in France, Great Britain, and the United States on the use of the large-hole burn cut has established cer¬tain advantages for this system. Advantages include longer pull and more complete fragmentation from blast rounds. However, research is needed to establish a set of parameters for optimum performance. As part of the Bureau of Mines Advancing Mining Technology for Marginal Resources program, the Twin Cities Mining Research Center, Twin Cities, Minn., acquired a horizontal rotary drill capable of boring holes up to 24 in. in diameter. This was used for a series of underground experiments at White Pine mine, White Pine, Mich., during 1973. Exceptional results were obtained with a 12-1/4-in void hole that yielded up to 18 ft of pull in a 10- by 20-ft drift, Fragmentation was excellent, and the compactness of the muck pile facilitated loading.

Jan 1, 1975

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

By W. D. Musgrove, B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Cahaba coal field is the second largest coal—producing area in Alabama. This field underlies parts of Shelby, Jefferson, St. Clair, and Bibb Counties and has an area of about 270 square miles. The Cahaba formations contain a number of coal beds, about 8 of which are mined at present. Although the area contains many folds and faults, samples from various mines and beds indicate that, except for the variation in ash content, the coal from this field is very uniform in character and quality. It is a high-volatile bituminous coal used chiefly for steam-raising purposes and domestic fuel. The coal as mined usually contains too high a percentage of impurities to be marketed without some preparation. The majority of the mines have washing plants in which jigs are the favorite type of equipment, although at some mines tables are used for cleaning the slack sizes. The washing characteristics of the coal from the Cahaba field are very uniform and differ from those of the near-by Warrior field, in that the coarser sizes contain a much lower percentage of bony material than the finer sizes. In general, the bone increases with decrease in size. It breaks into thin flakes, making difficult its elimination in the cleaning process, and gives rise to what is known among the washery operators of the Cahaba field as the ""rash problem.""A previous publication 5 referred to rash from the standpoint of jig operation and suggested some means of handling it with jigs. This report presents the results of table tests on two samples of fine coal from the Thompson and Woodstock beds, respectively, of the Cahaba field to determine the influence of rash on table efficiency.This investigation has been made in connection with the study of coal-washing problems now being conducted by the U.S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators of Alabama."

May 1, 1934

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By R. V. Ramani

"The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety arc directly connected with mine atmospheric environments their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions arc also an indication of the remarkable professional progress being made in the field of mine ventilation.Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952.The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) arc the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history.It is worthwhile to ask, ""How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?"" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and. in some cases, what constitutes good ventilation practice."

Nov 1, 1995

By A. Oyler

The U.S. Bureau of Mines has compiled data on the major causes of fatal and nonfatal electrical accidents related to mining, and their associated costs, for the 1980-85 period. Specific electrical problem areas were identified, allowing future research to be focused on reducing the frequency of these occurrences. Recommendations for reducing the number of electrical accidents and injuries are provided. The four mining sectors for which data were gathered and compiled are (1) underground coal mines, (2) surface at underground coal mines, (3) underground metal-nonmetal mines, and (4) surface at underground metal-nonmetal mines. Nine categories of information pertaining to specific aspects of the accident are used in this report: activity engaged in when the accident occurred, source of injury, job title, mining method, location, machine, nature of injury, accident type, and part of body affected. The number of years of experience at the specific job the employee was performing when the accident occurred, time of accident, and in the case of nonfatal accidents, the total days lost per year, are also summarized.

Jan 1, 1990

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999