Search Documents

By H. P. Rue

For the proper control of gasoline treating plants there is need of a quick test for corrosion. In "sweetening" gasoline that is, in treating it to remove evil smelling mercaptans or to convert them to disulphides or sulphides the sodium plumbite ("doctor") method is generally used. This method involves agitation of the gasoline with "doctor solution's (sodium plumbite made by dissolving litharge in a solution of caustic soda) in the presence of free sulphur3. One of the common mistakes in the technique of this process is the addition of too much free sulphur, which will dissolve in the gasoline and cause it to be corrosive. In the operation of a continuous sweetening; or treating plant, a check on the corrosiveness of they product is imperative at all times. The copper-strip test commonly used in specifications take, so long to perform that the plant may fail to function properly for some time before the operator discovers it. The writer has investigated a rapid corrosion test method involving the use of metallic mercury, recently developed by Messrs. G. T. Granger, refinery superintendent, and A. B. Comstock, chief chemist, of the Barnsdall Refineries, Inc., Okmulgee, Okla. They have used this test successfully for several months in controlling the operation of their continuous treaters any have come to the conclusion that it has several advantages over the copper-strip test. Chief among these is the time caved, as the copper-strip test takes at least one-half hour, while the mercury test can be wade in about five minutes. It is very evident that this is an important item in controlling a continuous treater.

Jan 1, 1928

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By Ruth F. Brinkley

This report is the 17th of a series originally issued annually, and more recently bienially, to acquaint the reader with the work of the Division of Explosives Technology, Federal Bureau of Mines. It differs from preceding reports in that its material is presented in two parts: Part I reviews briefly the overall activities of the Division during fiscal years 1955 and 1956;4/ part II presents in abstract form, the publications of the Division during that period. As it is not unusual for research completed in the course of one report period to be published only in the following period, the Bureau believes that the present approach will give a more accurate presentation of its work for the period considered. The Bureau hopes too, that the somewhat more concise presentation will prove convenient to the reader.5/ PART I -RESEARCH AND TECHNOLOGIC ACTIVITIES The activities of the Division during fiscal years 1955 and 1956 reflected the steadily growing preoccupation with factors affecting the safety of permissible explosives and those affecting the tests used for approval of these explosives. Findings by a team of French investigators prompted a study of the influence of atmospheric moisture on the ignition of firedamp by

Jan 1, 1961

By H. A. Watson

This circular, which is a revision and combination of two previous publications,3 4/ presents information on the different types of equipment that may be used to analyze mine atmospheres, with particular reference to the application and limitations of each type. Such information is frequently requested by mining companies, State mining departments, and other agencies concerned with safety in mining who wish advice regarding methods of analysis of mine atmospheres and the equipment necessary for establishing laboratories for that purpose. Since the Haldane-type apparatus is particularly applicable to the accurate determination of carbon dioxide, oxygen, and combustible gases such as methane in mine atmospheres, that apparatus and the method of operation are described in detail. The circular presents results of a critical study of the accuracy attainable with the Haldane-type apparatus in the determination of methane in concentrations of the order of 0.25 percent, by volume. Analytical procedures involved in the other methods discussed are presented in publications referenced in this circular. Information is given also on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres, and suggestions on laboratory design are included. INTRODUCTION 'The analysis of mine atmospheres plays an important part in promoting safety and maintaining safe conditions in mining operations, particularly in coal mining, where the flammable gas methane presents a continuous hazard in Nome mines and may be encountered unexpectedly in others.5/ Methane has been encountered also, often unexpectedly and with disastrous results, in noncoal mines and in tunnels under

Jan 1, 1956

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig. 1). The average fuel requirement per barrel of crude oil refined has remained virtually stationary for the past 3 years. Thus in 1937 the average was 562,000 B.t.u., in is it rose to 567,000 B.t.u., and in 1939 it declined to 557,000 B.t.u. she largest gains in fuel economy cane a decade or so ago on the widespread introduction of heat exchanges and pipe stills. In recent years many successful innovations in heat saving have been adopted, but the combined effect of those is completely masked by the degree to which the capacity is utilized. Some heat requirements are relatively inelastic, so the average consumption per barrel of crude oil refined tends s to increase when the operating ratio (crude runs divided by capacity) declines and vice versa. In 1939 crude runs to stills increased 6 percent (from 1,165,015,000 barrels in 1938 to 1,237,840,000 in 1939) compared with a decline of about 2 percent in 1938. The operating ratio in 1939 was 82 percent compared it's 78 percent in 1938.]

Jan 1, 1941

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By Jack I. Paige

The devitrification of lithium silicate glasses was studied to determine the effect of annealing temperature, composition, and additives on nucleation and crystallization. High-purity glasses, prepared from reagent-grade chemicals, had close to optical quality when prepared by a vacuum induction melting method developed during this research, The progress of devitrification was traced by differential thermal analysis and thermal expansion for those lithium metasilicate-silica compositions containing 80 to 90 percent silica. Microscopic studies of glasses partially devitrified at various temperatures and annealing times indicated that the primary initial mode of formation of individual crystals ,vas from densely crystalline zones that filled in as crystallization advanced Of the additives tested, calcium, potassium, and sodium helped promote devitrification with the least cracking or surface deformation. Tin oxide was most effective in reducing volume contrast ion during devitrification, but was not ClS effective in preventing cracking as calcium or potassium additions.

Jan 1, 1965

By E. A. Loria

The Bureau of Mines analyzed the effects of oxygen, nitrogen, and carbon on the tensile properties of electrorefined vanadium in terms of the Petch equation. The effects of the different impurities and grain sizes on the yield and flow stress between 2730 and 770 K were studied. For specimens of like composition, the values of the Petch parameters 01 and ky obtained by two different methods, extrapolation and grain size, were nearly the same. For high-purity electrorefined vanadium, the 01 value at 2730 K was 10,300 psi (5,150 psi shear). The 01 values for this metal at 1950 and 2730 K were lower by factors of 3 to 4 than for three less pure samples of commercial vanadium metal of equivalent grain size. Nitrogen was more effective than oxygen in increasing 01' the increase being about twice as much for the same impurity level. Carbon produced a slight increase in 01 up to 0.024 percent and then a gradual decrease in 01 to 0.11 percent, the maximum carbon content studied. The corresponding ky values followed the same trend in regard to oxygen and nitrogen additions, whereas the addition of carbon produced no variations at either temperature. Dislocations in vanadium are anchored by carbon, oxygen, and nitrogen with increasing firmness in that order. The high purity of electrorefined vanadium was confirmed by low yield stress and high ductility throughout the low temperature range. The metal also exhibited profuse twinning with high ductility at 1230 and 770 K. The effective surface energy for fracture, y, was found to lie between 3.3 and 3.6 x 1()4 erg cm-2?

Jan 1, 1966

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By P. C. Good

Work was done to determine conditions necessary for efficient electrodeposition of aluminum from fused chloride electrolytes. Aluminum was deposited from a molten chloride salt electrolyte over a temperature range of 150° to 750° C. At lower temperatures in a heat-resistant glass cell, aluminum was deposited on stainless steel and on aluminum cathodes. The deposit was recovered in the form of light, feathery dendrites that could not be consolidated. At 750° C, molten aluminum was deposited at cathode current efficiencies as high as 90 to 100 percent on titanium diboride cathodes and in molten aluminum cathodes. Nitride-bonded silicon carbide was the best cell material, although porcelain was also used. The electrolyte consisted of a mixture of sodium and potassium chlorides in 1 to 1 mole ratio, containing aluminum chloride in concentrations ranging from 2 to 30 weight-percent in cells holding up to 1,000 grams of electrolyte. Generally favorable results were attained in studies made at temperatures greater than the melting point of aluminum.

Jan 1, 1966