Search Documents

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By George A. Morgan

The successful expansion of crude oil production begun in late 1977, led to promising development of the nonfuel minerals sector. Although actual production of nonfuel minerals was limited both in variety and in percentage of output on a world scale, the potential for expansion with a rapidly developing infrastructure was significant. The energy base was expanding with construction of two new hydroelectric powerplants in addition to the existing plant near Edea. The Song Loulou plant will have a 240-megawatt capacity, and a hydroelectric plant under construction in the northern part of the country by mainland China will have 72 megawatts of installed capacity. Inflation of between 15% and 20% resulted in a real gross domestic product (GDP) of $2.8 billion2 in fiscal year 1980 (July 31 to June 1), up 6% from that of the previous fiscal year. Petroleum became the leading export item in terms of value, surpassing coffee and cocoa exports. Mineral exports as a whole increased eightfold in value, mainly because of oil sales. Oil exports also caused a reduction in the trade deficit by nearly one-third, and the Government expected its 1980-81 budget to be balanced at $1.17 billion. The Port of Douala accounted for about 8 million tons of cargo, or 93% of total maritime traffic for Cameroon. Expansion plans for the port call for an initial increase to 5 million tons, and a cargo handling capacity of 7.5 million tons in 1985 and 10 million tons by 1990. The Port of Victoria will gain importance with the startup of an oil refinery. The country's third seaport at Kribi was used solely for timber shipments, and capacity at the Port was to triple by 1981. The Government operated its own shipping line with six oceangoing freighters. France was the dominant trading partner, accounting for 25%

Jan 1, 1982

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By Richard L. Sanford

This report summarizes the results of an update on a previous Bureau of Mines grant (G0264026), and includes 5 additional years of computer pro-gram development. The directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various governmental agencies. References to computer applications throughout the industry are presented as well as comments on program availability. The work effort on the updated directory concentrated on programs that are available to the public and are well documented.

Jan 1, 1982

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area or the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using ?big hole? drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in detail.

Jan 1, 1978

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By Sheridan J. Rodgers

Toxic fumes generated during shot firing were measured in a phosphate rock mine and a copper mine. Fumes generated during firing of explosives in the Bureau of Mines 1350 ft3 test chamber were measured also. The release of fumes from water gels, ammonium-nitrate oil mixtures and nitroglycerin based explosives was studied. Direct reading instruments were used to monitor the fume concentrations. The amount of CO produced per unit weight of nitroglycerin explosives (0.41 ft3/200 grams) was higher than that produced by ammoniumnitrate-oil mixtures (0.24 ft3/200 grams) and water gels (0.16 ft3/200 grams). The amount of NOx produced by nitroglycerin based explosives was also higher than the amount produced by water gels or ammonium nitrate-oil mixtures.

Jan 1, 1976

By Thomas Fraser, E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916/ and an investigation of Illinois coal-w.ashing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coa 1.

Jan 1, 1925

By C. W. Morris

The continuous miner training system provides classroom materials training aids, and a continuous miner simulator to provide a short, intensive instruction and skills development program for training or retraining continuous miner operators. This project included refinement of training objectives, revision of training aids, improvements to the simulator, and evaluation of the entire system. This report describes the revised classroom materials and the validation of the training system.

Jan 1, 1982

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year's activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By Francis E. Federspiel

Based on the investigation by the Bureau of Mines, tungsten is the principal metal found in the study area; gold and silver were the primary metals found at one property. Tungsten occurs in tactite zones formed near contacts of calcareous metasedimentary with granitic intrusive rock. Gold and silver were found primarily along quartz veins in granitic rocks; small amounts of those petals also occur in the tactite zones. Since 1856 approximately 200 lode claims or relocations have been recorded, mainly in the southwest corner of the study area. Tungsten production in this part of the area has been inure than 7,800 short ton units (70,800 kg) of tungsten concentrates; about 4,800 short ton units (43,500 kg) were from the Mud Lakes Mine; and 3,100 short ton units (27,200 kg) were from the Rainbow Mine 1/.

Jan 1, 1981

By Dennis J. Grigal

The objective of this contract was to monitor operating conditions of, four flooded, fibrous-bed filter panels used during normal underground mining operation and to analyse clogging and structural problems. After observing structural and clogging problems and conducting laboratory and field tests, a final, Flooded, fibrous-bed filter design which minimizes clogging and structural problems was recommended to the Bureau of Mines. This report also describes the dust sampling procedures used to determine the dust concentration at the flooded, fibrous-bed scrubber intake duct.

Jan 1, 1979

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee' water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Walford S. Wright, NORMAN EBBLEY

During the past decade (1937 to 1947), including the war years of heavy demand for metals, the United States realized about one-eighth of its antimony requirements from domestic production, chiefly in Alaska. In World War II, our foreign supply sources became endangered; and uncertainty in our Far Eastern supply made this nation focus on Alaska’s mineral resources with a Production Gear that centered in the Bureau of Mines experimental station at College (Alaska). The development work known as District or central deposits. The strategic mining districts included that of central Alaska was reorganized at Ketchikan Mining Districts. Mines were located here had produced considerable quantities since 1901; but methods for exploration had come from 1936 to spring 1942, some $4 million produced in gold alone. Statistics relating to available ores are those selected by type and exploitation periods with wide variety applied. During the summer of 1941, as part of an extensive Geological Survey program continuing through funds provided by U.S., geological surveys spent six weeks mapping an area approximately two square miles surrounding mines. The mines working both surface & underground work employed these men in mapping exercises.

Jan 1, 1948

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977