Search Documents

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

By J. McCoy

Charged sprays and fog have been evaluated for reducing respirable dust concen¬trations. Charged spray technology was reviewed for effectiveness, equipment and theoretical considerations. A mathematical model was developed for predicting dust reduction effects. Laboratory tests were made showing charged spray is considerably more effective at reducing dust on a unit water basis than hydraulic spray. Positive and negative sprays are equally effective. Combined polarity sprays are considerably less effective than either polarity alone. Little difference in effectiveness by dust type was observed. The charged cloud can present a spark hazard in explosive atmospheres. Due to this spark hazard from the charged droplet cloud this technique must not be used in gassy mines. Predictions were made for field test conditions but confirmation was impossible due to particles resulting from dissolved solides in the spray water. Dissolved or suspended solids in atomizing sprays can result in an increase of the respirable dust burden. Charged sprays are an available dust control technique best suited to applications where water usage must be limited and long contact time between spray and dust is possible.

Jan 1, 1983

By R. C. Adams

This report describes the feasibility of mining the oil-shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt, at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By W. T. Benson

The Bureau of Mines has undertaken investigations to examine selected deposits of beryllium throughout the United States. The beryllium deposit about 6 miles southeast of Lone Pine in the Owens Valley region of Inyo County, Calif., was among those selected for study. In 1960, field work was conducted on the Inyo Beryl claim to determine the extent and character of the beryl-bearing deposit. This report describes the work that was done. In the area investigated, the beryl occurs disseminated in granite and limestone and as stringers. Apparently, the stringers are related to nearby pegmatite dikes, inasmuch as some appear to contain fine-Grained pegmatite. Granitic rocks enclose most of the stringers, which occur as fracture fillings, ranging from thin seams to 4 inches in thickness. The stringers are of muscovite, quartz, albite, and beryl. Some also include epidote and fluorite. For the most part, they are widely spaced. Therefore, mining of substantial tonnages averaging better than 0.2 percent beryl does not appear feasible.

Jan 1, 1962

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By William G. Hedling

The operation of electric face equipment in underground coal mines has proven to be extremely hazardous to mining personnel, including equipment operators and others working in the vicinity of active equipment. Recent industrial engineering studies* of accidents and fatalities indicate that a major contributor to this hazardous situation is noncompliance with modern principles of human engineering, particularly lack of standardization of control configurations. Control configurations differ not only among different machine types, but also among the same machine types produced by different manufacturers. This lack of standardization can produce a high incidence of error in the operation of electric face equipment, thus creating a potential source of accidents. Other examples of non-compliance with human engineering principles are the widespread use of identical black, round control knobs (regardless of the function being performed), and the inappropriate location, spacing, and labeling of controls. Any or all of these factors may place the operator in a "negative transfer" situation, which means that control manipulations appropriate for one type of machine are different from (or even the reverse of) the control movements required to produce the same effect on other machine types. This situation increases the accident potential to the operator, as well as to others in the vicinity. Accident potential is further increased by circumstances which do not allow for large error tolerance-specifically, emergency procedures. Reports of accident statistics cite operator inexperience as a primary cause of most accidents involving underground electric face equipment. Several factors contribute to operator inexperience, including: 1. High personnel turnover 2. Employee absenteeism 3. Current union practice of bidding for jobs.

Jan 1, 1974

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By M. O. Serbousek

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed an eight-piece precast reinforced concrete drift set for a small opening. Twenty-two sets of three different member sizes were tested to destruction under two loading conditions. A discussion of the test results and typical failure patterns is presented.

Jan 1, 1969

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Kenneth L. Whitehead

After many years of research, the occurrence of pneumoconiosis, black lung disease, among miners has been related to the mass of respirable coal dust to which mining personnel have been exposed. Congress passed Public Law No. 91-173 in 1969, which limited the dust concentration of respirable dust allowed in the mine working areas to 2.0 mg /M3 as of December 31, 1972. As a result of these restrictions, much work has been done in determining methods of either eliminating or suppressing respirable dust. The purpose of this project is to determine the state-of-the-art in continuous mining machine bit technology, particularly with regard to dust production.

Jan 1, 1973

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By James N. Bayne

An examination and analysis of Landsat digital data in the monitoring of surface mines in selected counties of South Carolina.

Jan 1, 1979

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959