Search Documents

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

By R Frank' Mammele Chiappetta, Conny Postupack

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1988

By W. De Graaf, C. Mkumbo

Bulyanhulu Gold Mine Limited (BGML) commissioned a project of sinking a Bulk Air Cooling Shaft during its programme to improve the ventilation system on the mine. As part of this project, a ventilation drift had to be developed and holed into the Main Shaft at 4920 Level. AEL Mining Services (AEL) were requested to provide a technical solution, which included monitoring of blast induced vibrations and to design drilling and timing plans to ensure blasting activities on the vent drift were conducted without disrupting the main shaft’s infrastructure.

Jan 1, 2011

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Shuli Teng, Vladimir Sujansky, Matthew Rawls, Ivan Junarsa

In recent years significant advances have been made in chemical processing technology. In particular, process intensification using micro-technology has had some success in changing and improving chemical processes including mixing. Process Intensification is the miniaturization of unit operations and processes whereby a smaller compact piece of equipment takes the place of a larger one at the same given capacity or mass flow rate. This paper summarizes research into the application of the technology for manufacture of high internal phase water in oil ammonium nitrate emulsions (ANE’s) at low energy cost and with very low oil/fuel blend content. The emulsions can be used as precursors for preparation of explosives. The quality of the emulsion prepared was assessed through droplet and crystal analysis and compared with that of emulsions made by conventional large scale jet mixing technology.

Jan 1, 2014

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By Thomas Barkley

Mining tradition holds that a parallel round underground can not be any deeper than it’s smallest face dimension. ln other words, a mine using a 12’ (3.7 m) high by 24’ (7.3 m) wide room and pillar mine, the deepest pull that can be achieved is plus or minus 12’ (3.7 m). After experience with decking of rounds in a 12’ (3.7 m) diameter shaft to achieve more than 12’ (3.7 m) advance per round, the concept of deepening the pull on horizontal parallel rounds seemed to be a feasible concept. Tests were conducted in a conventional room and pillar metal mine with a round size of 12’ (3.7 m) high by 24’(7.3 m) wide. Standard rounds were drilled with a 16’ (4.9 m) steel as parallel rounds to an average depth of 14.5’ (4.4 m). The average depth of pull on these rounds was about 13’ (4.0 m). Using the available drilling equipment, 20’ (6.1 m) drill steel was used to drill holes to an average depth of 18’ (5.5 m). Five rounds were drilled and shot with a resulting aven$e pull of 16.2’ (4.9 m) or 90 % of drilled depth. Rounds were designed with decked bum cuts to maximize depth of pull in the cut area An innovative method of de&mining drilling accuraq was used to estimate it’s effect on depth of pull in the rounds. This method used a standard automatic 35-mm camera and scaling to determine the average drill deviation for many of the holes in the rounds.

Jan 1, 2000

By Xue Yongpeng, Zhu Zhenhai, Zhu Ming

The purpose of the Solid Medium Controlled Blasting Technique and Its Applications is to have the inside of the vessel-shaped framework (e.g: oil tank , water pool, gas chamber, chimney, water tower, grain warehouse and etc.) or the one side of the thin wall-shaped structure(e.g: steel bar concrete wall and etc.), both of which are intended to be demolished, inserted with the required solid medium (e.g: soil , sand , coal, salt and etc.) ,in which there is a certain mass density, and then through which the blasting energy is transferred to fulfill the blasting task. For such a technique, it is necessary to bury the explosives into the inserted solid medium and then to start the explosion to blast the intended target into pieces. The filling of the solid medium may be done mechanically or by man. Compared with the water pressure blasting technique, this one has the characteristics of good effect. wide application, simplified construction procedure , safe and reliable operation and small vibration (less vibration than water pressure blasting by 80% to 90%)in particular without any flying stones, thus resulting in better and comprehensive social and economickfficiency.

Jan 1, 2000

By Tapan Goswami

A column of stemming material keeps explosion gases at high pressure for longer times in a blasthole. In general, use of appropriate stemming enables the achievement of the desired level of fragmentation and looseness of muckpiles, as well as the reduction of airblast and fly rock. The ejection resistance of a stemming column varies with the type of stemming material employed. In an effort to optimise stemming at Mt Owen Mine in the Hunter Valley, Australia, a trial was conducted to assess the efficiency of two types of stemming materials. Mt Owen mine relies on through seam blasting and stemming quality is important in this challenging blasting environment. Each type of stemming was trialed in different section of a blast. The blast was designed using Orica’s SurveyPlus@, LoadPlus@ and ShotPlus@ software. Measurement was done using high speed filming of the blast and then post blast information was obtained from analysis of the film. Data analysis included determination of the ejection velocities and percentage swell. Digging rates were measured from excavator production rates. Despite the presence of rounded surfaces and finer particle sizes, River Pebble stemming material showed superior ejection resistance. It also appeared to perform as well as more angular and expensive Crushed Stone, a finished quarry product, based on excavator productivity and heave. It was recommended that future blasts at the mine be stemmed with the River Pebble stemming material.

Jan 1, 2000

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025