Search Documents

By Wayne A. Charlie

An experimental test program being conducted at Colorado State University and involves the study of the behavior of water saturated sands under shock and explosive loadings. The study is being conducted to evaluate potential blast induced changes in dynamic soil properties, soil shear strength loss (liquefaction) and densification of water saturated sands under single and multishock loadings. This paper presents testing and measurement objectives, and the equipment and instrumentation developed to load, measure, record and analyze the transient and long term soil behavior. The laboratory shock facility is capable of generating multi-shock pulses with milli-second rise time, peak stress amplitudes of up to 35,000 KPa (5000 psi), peak particle velocity of 5000 cm/set and peak acceleration of 10,000 g. The field explosive facility subjects saturated soil to controlled explosive loadings. Of major interest is the soil strain and water pressure, both during and after the passage of the stress wave, as a function of peak particle velocity, peak strain, loading rate, soil density, initial confining stress and the number of loadings. Based on data obtained to date, soil densification is due to consolidation following liquefaction.

Jan 1, 1991

We had a cold, gray winter here in Kansas City and I spent a lot of time watching out my den window at the squirrels and birds trying to get by in the lousy weather. I remember too well working in the cold, loading shots. I was frostbitten several times since I couldn’t tie in MS connectors with gloves on. Those old connectors had a piece of detonating cord on either end of a metal tube that held the delay and you tied them to the trunk lines with square knots. Doing this on a “warm” day in Alaska or Montana shooting ditch for a pipeline could be a frosty experience. Also remember how hard it was to connect up electric caps (detonators to you new guys) in the cold. Now I don’t want you to feel sorry for me ‘cause I suspect most of you younger fellows have also paid your dues in the cold and for that matter in the heat too. Wowee, the heat at the bottom of a Chicago dolomite quarry in August was enough to fry the brains of all that were there. Maybe that’s why the third deck of my brains doesn’t exist.

Jan 1, 2004

By L C. Taylor, H U. Lesiste

This paper describes a method for estimating the density distribution in the soil cap as a function of distance from its top at the time of impact with the target. It provides an estimate of the density distribution in the soil on the center line of the soil cap at the time of target impact for a single depth of burial of the charge and two heights of target and shows that, for the heights of target and the depth of burial considered, the thickness of the soil cap first increases from the in situ value and then decreases. The distribution of soil density along the centerline of the soil cap changes significantly with distance from its original position. These results can be used for validating hydro-code computations and the soil models used in the computations.

Jan 1, 2011

By Mohsen Sanai, Paul Gefken

"SRI International has developed and patented* a castable dilute explosive tile @ET) that offersunique advantages over conventional high explosive. The primary advantages of DET are that itsdetonation pressure can be adjusted over a wick range and its impulse can be controlled independently by adjusting its thickness and configuration. Because DET has a much lower detonation velocity than conventional explosives, the pulse duration produced by DET is as much as 10 times longer than the pulse duration produced by conventional explosives for equal explosive weights. These features of DET present several advantages to the mining industry. For example, DET can be tailored so as to control fragment size and distribution to enhance extraction of desired elements from ore or breakup of specific regions."

Jan 1, 1995

By Ian R. Firth

For the majority of open pit precious metal mines in the western United States, grade control practices have evolved as a direct result of the variable geology of the ore body and the lack of a clear visual or geologic distinction between ore and waste material. These practices often include the extensive use of buffer or choke blasting, in an attempt to minimize lateral movement of the muckpile. The Mackay School of Mines is conducting ongoing research, which aims to develop a practical method of measuring the movement of discrete “targets” placed within the body of the blast. The movement experienced by these targets can then be used to interpolate the movement of the blast as a whole. Typically, the boundaries between different material types are known as digging limits or polygons and are marked using colored flagging on the muckpile. If material movement can be measured using targets placed in the blast, these digging limits can be altered to reflect the blast-induced rock movement, reducing dilution and improving value recovery.

Jan 1, 2002

By David Weidner

Public relations, regulatory compliance, determination and implementation of pre-blast inspections, and accurate blast monitoring data are all essential components when conducting blasting operations for a large scale, high profile, urban site development. By working closely with the contractor, an independent vibration consulting firm can provide the commitment of time, energy and resources to tie all of these elements together. When this comprehensive approach is properly implemented, problems often associated with projects of this magnitude can be almost completely eliminated.

Jan 1, 2001

When a company has an effective hearing loss prevention program, everyone wins-the employers, the employees, and the safety and health professionals who implement the program. This guidebook is not about minimal programs that meet only the letter of the law. It is concerned with programs that are effective as well as efficient: those optimizing program elements that succeed in preventing hearing loss in a practical and cost effective manner.

Jan 1, 2006

By Victor C. Bryan

"One of the more challenging issues facing operators of U.S. mines and quarries is blasting in an environmentally acceptable way. It is quite important that industry management understand and apply guidance, discipline, and control in the exercise of blasting operations. This presentation is a discussion of problems related to that environment away from the blasthole that may or may not be adversely affected by blasting and the steps management may consider in resolving resultant problems. In any case, one of the main concerns that will continuously be brought up is thatmanagement procedures inherent to good blasting is a uxporate responsibility of the mine or quarry business entity; and can not be delegated to the explosive manufacturer or supplier. This management attitude, based on education, training, and the comprehension that the process of production begins with drilling and blasting and consumes a significant amount of overall production costs."

Jan 1, 1995

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

Jan 1, 2002

By Bruce Notthup

Using a Three Dimensional Laser Profiler, persomrel from Austin Powder were able to determine drilling patterns for use in underground mine Room and Pillar blasting operations, The faces had got out of alignment, causing concave faces across the 100 feet wide, 28 feet high tunnels. This was leading to poor drilling and poor blasting results. By profiling the faces, modifications could be made to the drilling pattern to help gradually straighten the faces. The Laser Profiler was also used to check the accuracy of collaring the holes and also perform post blast surveying of the positions of the bootlegs. This allowed recommendations to be made to improve drilling operations at the face. In addition, other volumetric calculations could be performed using the systems’ surveying software, all a lot more easily and quickly than by standard methods.

Jan 1, 1994

By Douglas A. Anderson

It is quite common for people exposed to blast vibrations to ask questions such as "How big was that blast on the Richter Scale?" Although it is tempting to dismiss such questions out of hand, for the lay person it is understandable that something which shakes their house should have some sort of measure attached to it. Since a layman doesn't usually know about particle velocity, frequency or the other terms used in describing and regulating blast vibration, the Richter Scale is usually the only measure they can relate to.

Jan 1, 1994

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By S. J. Dillingham

As we enter the new century and close out the old, it has become standard procedure for most blasters to complete a blasting log or shot report following a blast. However, how can you be sure these completed blasting logs are worth the paper or electronic space they occupy.3 Is the recorded data accurate and meaningful? Will the blasting logs stand up under investigation? This paper will attempt to define the purpose of a blasting log, illustrate common mistakes, discuss potential problems, and indicate steps that a company or individual blaster can take to improve and protect against costly errors. The end result will be a reminder of the importance of accurate documentation following a blast that must be given the same individual effort as went into the blasting itself. This paper will also attempt to achieve a proactive training resource to improve the use of blasting logs. A completed blasting log is, quite possibly, the only witness to the overall credibility of the work of the responsible blaster. The log may remain perpetually silent, only to end up in a file that is moved progressively with time to various levels of long-term storage. But, will this silent witness be ready to speak out should a concern arise from the blasting ? Will the blasting log communicate with authority and credibility, or will it be ridiculed by investigation and silenced in shame with costly adverse results for the blaster and company? It is not enough to simply complete a blasting log. The information it contains must be accurate enough to stand the test of time and arduous scrutiny. Unfortunately, most blasters and their associated blasting companies do not realize the status of the silent witness until it is too late.

Jan 1, 2000

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By Paul Kunze

For some of us, the most disagreeable part of being the blaster- in - charge is doing the required paperwork. Cost coding on time cards, drilling reports, magazine inventory logs, and blast records all eat into our time. When all goes well, which I suppose is 98% of the time, the blast records are submitted and filed, probably never to be seen again. Sometimes a progressive operation will use the information documented in the blast reports to evaluate blasting effectiveness and improve results. When the report is consistently used in this fashion, costs can be reduced and other efficiencies will be realized. A blast report in times past was a simple form that mainly was used to keep track of the drill footage and of the powder used in the shot. However, as the population and consequences of careless blasting increase, multiple levels of blast documentation are now being required nearly everywhere, during all phases of the drill and blast process. We are now compelled to create preliminary blast designs prior to commencing work. We are required to submit pre-blast plans before each shot, and we need to generate post-blast reports that document the details and results of each shot.

Jan 1, 2004

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool to evaluate the success of ground preparation. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile diggability. This approach is considered to provide a very comprehensive survey of post blast conditions since such a shovel interacts which every cubic yard of a blast.

Jan 1, 1990

By P D. Katsabanis

The dynamic tensile strength of geomaterials is known to be highly dependent on the strain rate of the load applied. This is significant in applications where the material is subjected to shock waves and impact loading. This paper proposes the use of a simplified method to determine the dynamic tensile strength of hard brittle rocks using an explosively impacted version of the Hopkinson Pressure Bar. A compressive stress wave was propagated in a sample, representative of the material of interest, by detonating a small charge at one end of a cylindrical sample. The tension wave, generated upon reflection at the free face, causes spalling in brittle materials. Strains at four points in the specimen were continuously measured and the dynamic tensile strength was determined by applying the one-dimensional wave theory.

Jan 1, 2010

By John Brulia

It has been said that the only thing that remains constant is change. After more than 33 years in the explosives industry, I do not take any exception to that adage. I have seen changes in people, changes in ownership of companies-both small and large, domestic and international; changes in products; changes in the way we use products; changes in the way we handle products; changes in regulations; and last, but not least, changes in our perceptions of threats to our industry.

Jan 1, 2008

By Roberto Golchi

This article describes the method used to quantify the Environmental Impact for the mining, by drilling and blasting, of a borrow pit for a gravity-dam. The affected environment was broken down into a number of components, such as public health and safety, social relationship, air and water quality, flora and fauna. The effect of the various impacting factors from the mining activities, both directly and indirectly, was then calculated for each environmental component. To do this, each impacting factor was first given a magnitude, a number based solely on the range of scenarios possible for the impacting factor. A matrix of weighting factors was then derived to systematically quantify, and normalise, the effects of each impacting factor on each environmental component. The overall impact upon each individual environmental component was then calculated by summing the weighted magnitudes for all the impacting factors.

Jan 1, 2003

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003