Search Documents

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By Charles Zdazinsky

Many blasting applications in the mining industry demand that the hard rock being blasted remains structurally competent. For example, pre-splitting is a common technique to reduce fracturing, and operators of dimension stone quarries use this blasting method to eliminate overbreak. When pre-split design parameters are not applied correctly, there will be a redistribution of stresses within the rock, resulting in Blast Induced Rock Damage (BID). Advances in geophysical technology are enabling blast technicians to monitor BID and then use the results to correctly design their blasts.

Jan 1, 2011

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By S. M. Geerts, M. T. Wild

In this paper the performance effects of various shaped charge liner designs will be discussed. Several different charges will be tested and the liner design will be reviewed based on the performance in testing. The first type of shaped charge to be tested is a conical charge with dual confinement. For the purpose of this paper, dual confinement is a shaped charge with two liners but containing one explosive charge. Several charges with different dual confinement designs will be tested. Variations in configuration include charges with similar angle and similar diameter. The second type is a double conical shaped charge configuration. A double shaped charge will be considered to be two complete charges formed into a single cone. The goal of the project is to determine if any of the designs increase the efficiency and/or effectiveness of the shaped charge in comparison to the standard conical shaped charge. A standard conical charge will be detonated against a witness plate to get a standard depth of penetration or a baseline. All charges will have a seven cone diameter standoff, allowing the data to be compared to the control charge. Computer modeling will be used to predict the results of the testing that will be conducted. The actual results will be compared to the computer simulation for validation.

Jan 1, 2010

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

By Rhys Baker, Tim O’Brien, Joshua M. Hoffman

This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms.

Feb 1, 2020

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By Petr Mostak, Miroslav Horacek, Miroslav Stancl

Detection of plastic explosives is an important task in the security measures against criminal misuses of this type of explosive. Particles and vapour detectors are basic instruments in this detection. Colour reactions and dogs are also used. Marking system in accordance with requirements of Montreal Convention was developed and applied in full scale production of plastic explosives including Semtex since 199 1. The influence of marking on technology, performance and other properties of plastic explosives is discussed. 2,3 dimethyl 2,3 dinitrobutan is the most popular marking agent which is broadly used. The detectability of this compound is not optimum by some detectors. The substantial effort has been given to development of plastic explosives with controlled shelflife. Some results of this work are presented. Technical and economic aspects of identification marking are discussed.

Jan 1, 2001

By B. M. P. Pingua, M. Nabiullah

Number of mine accidents occurred in Indian surface mines are due to poor quality of explosives and blasting accessories. Amlori open cast project is one of the major coal producing projects in India. Standard drilling and blasting parameters are used to achieve desired productivity of the mine. 150 and 260 mm diameter blast holes are used for blasting in coal and overburden benches. Most of shovel benches are 12 to 16 m in height and dragline benches vary from 25 to 30 m. High-energy bulk emulsions are used for blasting. The cup density and velocity of detonation of bulk emulsion explosives are 1100 to 1200 kg/m3 and 3.8 to 4.5 km/s respectively. An incident occurred on fire bench of Amlori open cast mines during mucking of blasted muck.

Jan 1, 2008

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

The following situation was submitted as an ethics case study for inclusion in the Journal. To the best of our knowledge, they are based on actual circumstances encountered in the field. Blowing the Whistle Protecting Confidentiality or Doing the Right Thing? This case centers around a construction job and involves a contractor, subcontractor/blaster, and a farmer/homeowner who lives near the job site. It is essentially a study of professional ethics versus morality, our professional code of conduct versus what is right or wrong.

Jan 1, 2007

By K. M. Kim, J. B. Kemeny

A case study was conducted with 5 shots with varying pre-blast block sizes and explosive energies. From this case study a site-specific predictive fragmentation model was developed. There are two main innovations in this study. One is using an image analysis program (Split-Desktop 3.0) on the bench face to obtain the pre-blast block size (F80) quickly and consistently. Another innovation is to utilize the Schmidt Hammer Hardness (SHH) to estimate intact rock strength.

Jan 1, 2011

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By August Ferraz Ribeiro, Guilherme Dias Mendona, Paula Henrique Lisboa, José Silvio Corsini

Correct slope adhesion is related to the conformity of the slope’s real geometry to slope planning. It is very important in mining because slope design has economic and safety implications. Slope design conditions can interfere with mining waste and ore proportion. Without a correct wall, the development of the mine can be hindered, which can reduce the amount of ore available. Furthermore, correct slope design reduces the possibility of melting and allows traffic with equipment and people in the mine. However, defining the wall is a more complex work as the characteristics of the rock require the use of blasting techniques. Therefore, Enaex Mining Technical Solutions (EMTS), in partnership with the engineering team at the Chapada Mine, at Lundin Mining, has developed this study in order to increase slope adhesion. The basis of this study is a near-field vibration test, which enables the creation of vibration attenuation law, and a seed wave damage model has allowed the characterization of the rock present at the Chapada Mine. Then, we could compare the model result to the real slope adhesion achieved with the buffer technique used in the mine. Therefore, it was possible to relate the real result to the model result.

Feb 6, 2023

By L C. Taylor, H U. Lesiste

This paper provides a preliminary description of the properties of the output pressure (shock) wave of an end initiated, cylindrical charge of low height to diameter ratio in saturated sand. The properties of primary interest are the pressure wave velocity, peak pressure and rate of rise of peak pressure to within 1.4 charge diameters from the output end of the charge. The behavior of these properties is seen to be quite different from their behavior at more customary ranges in water.

Jan 1, 2013