Search Documents

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By Pejman Oghazi

During the last decade the output of mining companies has increased rapidly. The key driver is the increase in demand for raw materials in the developing world, and thus this demand has driven up ore prices. From the time when the Raw material group (year 2000) started to introduced their index, it was set to 100 points. Today, year 2011, the index is over 400, which means that ore prices have quadrupled since then. Mine companies have to go deeper in the mines to access the ore bodies to increase the mine capacity and to be able to respond to the market. By going deeper in the mine, there will be new challenges that have to be considered. One of these challenges is how to handle the mine water that is produced in the mine. The water has to be moved to the surface in order to keep the mine from flooding, and this causes more challenges. One solution is to pump the mine water up to the surface without treatment; however, this causes considerable pump wear and the water will still require treatment on the mine?s surface. Another solution is to treat this water in the mine before pumping it to the surface. Metso Minerals has a system solution to treat the mine water, by separating the solids from the mine water. This system reduces the erosion in the pumps and will save many maintenance hours in the long term. One other option is to use the treated water in a closed circuit and reuse it in the process. This system can be divided into three steps: Firstly, a spiral dewaterer to remove the coarse solid particles. For the next step, lamella thickener is used to remove most of the solids, and lastly tube press to handle the sludge from the underflow lamella thickeners. Keywords: mine water, mineral processing, dewatering, separating

Sep 1, 2012

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By Luis G. Bergh

Today, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design. In this work, a model of a rougher flotation circuit, based on operating variables and parameters fitted from industrial data, obtained in some previous work, is used to develop a set of logic rules in order to aid operating decisions. The simulator was first used to sensitize the effect of changing the froth depth profile on target variables, and then to find out the best profile to reject common disturbances coming into the plant. The flotation circuit simulator was redesigned to incorporate an expert system following the proposed control algorithm. Several tests were performed to evaluate the control responses to different correlated series of input variables, such as feed grade, tonnage, particle size distribution, and solid percentage. Control alternatives are discussed based on the circuit simulator. Keywords: modeling, industrial data, flotation control, mineral processing.

Sep 1, 2012

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate. The technology has been tested on several different waters in pilot plant campaigns. Results obtained indicate that potable water can be produced (containing less than 200 mg/L sulphate and no heavy metals) as long as the monavalent ions (Na+, Cl-, etc.) are within limits.

Jan 1, 2003

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By A. J. Ren

The ore, dealt with in this paper, is a certain rutile in Shanxi province, China. A trunk flowsheet with gravity concentration is used, and the TiO2 grade of rutile concentrate is about 90%, but the TiO2 recovery is less than 50%. In order to increase the rutile recovery, the laboratory test, using the truck flowsheet with flotation, is carried out. The flowsheet is that firstly floatable gangue is re-moved by flotation; secondly rutile is recovered by flotation; and thirdly impurity is separated by LIMS, HIMS, gravity concentration and flotation from the rutile concentrate. In rutile flotation, BK423, a phosphonic acid, is used as rutile collector, and Na2SiF6 is used as silicates depressant. The experimental result shows that the recovery of rutile concentrate is improved obviously, and the recovery of ultimate rutile concentrate is 68.01% TiO2 and 84.88% rutile. The TiO2 grade of first concentrate is 95.98%, and the TiO2 recovery is 45.60%. The TiO2 grade of second concentrate is 80.53%, and the recovery is 22.41%. Furthermore, magnetite and ilmenite are recovered in the flowsheet.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

By J. J. Liu

In the Bayer process, control of alumina trihydrate particle size, oxalate stability and morphology and foaming is crucial for improving the yield and quality of alumina trihydrate. One way to economically achieve such control is to employ specifically developed chemical additives, termed, crystal growth modifiers (CGM?s). In this paper, the mechanism of action and practical application of CGM?s in the Bayer process are summarized. The application of CGM additives allows for both enhanced agglomeration and secondary nucleation control, and hence coarsening of the particles. Current research efforts have utilized the information gained from mechanistic studies to enhance the performance of CGM products. It was demonstrated in both laboratory tests and industrial operations that the newly developed CGM formulations have a range of properties with enhanced performance, compared to the current commercial products.

Jan 1, 2014

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014