Search Documents

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By P. K. Fedotov

Centrifugal separation opens its new application fields in the Mining Industry. The up-to-date equipment for ultra-fine ore and concentrates grinding allows an efficient use of centrifugal concentration for micronic gold grains recovery. Moreover, advanced centrifugal concentrators are presented on the market: concentrators with continuous concentrate discharge designed both for ore and non-metallic minerals concentration process. The conducted tests proved the centrifugal concentration to be efficient process for gold recovery from finely ground concentrates and ores (less than 20 µm). Knelson concentrator application for such a fine material in different process circuits makes possible to raise the total gold recovery level of plants. In the circuits of coal plants and in course of coal slimes treatment the centrifugal concentration may be used before flotation in order to improve process performances. A centrifugal concentrator KC-CVD with continuous concentrate discharge working on 0.3 (0.5)mm fraction before flotation is

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By M. V. S. Cavalcante

The quality of iron ore pellets, represented in terms of parameters such as cold compressive strength (CCS) and Tumble Index (TI), has a strongly influence on the productivity and energy of reduction furnaces like the blast furnace and on the quality of hot metal or liquid iron. The main objective of pelletization operations is to produce iron ore pellets of desirable specifications and ensure high levels of plant productivity and energy efficiency. Advanced process control of an industrial iron ore pellet induration process using a soft sensor for pellet quality and fuzzy-logic based control algorithm is described in this paper. The pellet quality soft sensor consists of a rigorous mathematical model of the induration process and a statistical model for the pellet quality parameters. The mathematical model is based on the fundamental principles of heat and mass transfer between gases and pellets, kinetics of drying and condensation of moisture, combustion of coke, calcination of limestone, and melting and solidification of pellets. The predictions of wind-box temperature profiles are in close agreement with the measured profiles. The time-temperature profiles of the pellets during induration, along with raw material characteristics and induration process operating conditions, are used as inputs to the quality model to predict cold compressive strength and the Tumble Index. The predictions of the quality soft sensor along with the rules based on fuzzy-logic derived from simulation results and operator experience are then utilized to control the induration process to achieve precise control of the quality parameters and to optimize the induration process in terms of fuel efficiency and productivity. The mathematical model is also utilized as a soft sensor for temperature, moisture and composition profiles of pellets and gases. Results of implementation of this model-based control strategy on an industrial scale induration process will be presented. Keywords: iron ore, pelletization, simulation, process control, optimisation

Sep 1, 2012

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The methodology is to use plant data to build the models and to supplement this by laboratory data where necessary, for example the determination of breakage functions. The plant data come from comprehensive sampling surveys and so far 33 surveys of clinker grinding circuits have been carried out in 9 plants. The operating conditions have been• mill sizes – 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,• mill feed rates – 46 to 158 tonnes per hour,• air flow through mills – 25000 to 125000 cubic metres per hour,• cement clinker work indexes – 10.3 to 18,• separator sizes – 2. to 3.1 metres diameter,• separator feed rates – 132 to 689 tonnes per hour,• separator speeds – 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises on the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distributiongraphs are used to illustrate every aspect of the discussion.In case I the special emphasis on calculating the breakage rates and discharge rates separately is given in a high pressure grinding roll-ball mill-separator circuit. The tonnes of each size fraction in the mill and the calculated values of R/D, D and R are determined. The values of R per mw are also given to allow comparison with mills of other sizes. The circuit allows the comparison of the static type (V Sep) and dynamic type separators (SKS). Comparing the reduced efficiencies shows that the dynamic separator is slightly more efficient than the static one.In case 2 data are given from two compartment tube mills having the same diameter and the motor power but different ball size gradation. The breakage rate particle size variation of the second chamber of two mills indicate that having finer ball size distribution causes higher breakage rate values."

Jan 1, 2003

By Y. Rama Murthy

Around 90% of the chromite resources of India are concentrated in the Boula-Nuasahi Sukinda belt of Orissa state. In order to conserve these valuable ore resources strategically, several companies established chrome ore beneficiation plants in this region. The general beneficiation process in these plants consists of gravity unit operations such as Floatex density separator, spiral, wet shaking table etc. Most of these gravity circuits suffer huge losses of valuable minerals in the tailing. Any attempt towards decreasing these losses would not only increase the limited reserves in India but also make the economics of the operations more attractive. Apart from the liberation phenomena, in many of the operating plants considerable quantity of values are lost in the tailings, due to inconsistent feed quality, inappropriate selection of operating and design parameters. Mineral engineers in this regard have to play a proactive and continuous role to improve the performance of all separating units by modifying even small changes based on tests conducted in laboratory under controlled conditions followed by attempts to make necessary changes in the plant. For such improvements, accurate data collection and proper data interpretation followed by making necessary change which is implementable in an operating plant play a very critical role in performance of the circuit. Databank collected over a period of time under various conditions would also help in overcoming the future problems related to either variation in the feed characteristics or specific demand by metallurgical industries. The above concept was adopted in one of the operating chromite beneficiation plant at Sukinda. The approach adopted and practical problems encountered during the study were reported in this paper. The result of trial campaign has shown that, an overall product assaying 30.2% Cr2O3 from the feed (18% Cr2O3 ) can be produced to in single stage. The final discards of the process contain 12% Cr2O3. Keywords: chromite, chromite beneficiation, chromite losses, gravity concentration techniques, plant operating data bank

Sep 1, 2012

By C. L. Lin

Previous research on particle damage during high pressure grinding roll (HPGR) crushing was limited by the resolution of point-projection micro CT systems and the extent of damage was described by the percent of particles cracked for different crushing methods as determined at a voxel resolution of 40 microns. With recent advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. With the use of X-ray lens imaging the resolution is determined by the lens rather than by the spot size of the micro-focus X-ray source. The high resolution X-ray micro CT (HRXMT) system made by Xradia with a voxel resolution of less than 1 micron is now being used for the characterization of particle damage during HPGR crushing. In this way, the direct 3-D determination of the internal damage of crushed ore particles which vary from 40 mm down to 100 microns in size is being studied at a voxel resolution of a few microns. The number, size, and shape of cracks can now be measured at this improved resolution and for the first time the specific crack surface area distributions of the crushed product can be calculated from HRXMT images using specially designed software tools for 3D analysis. Results from selected crushing operations are presented. Copper ore particles from HPGR crushing at high pressure (6 N/mm2) are severely damaged having crack specific surface areas as great as 10 mm2/mm3. Keywords: HPGR, particle damage, X-ray micro tomography, crack surface area

Sep 1, 2012

By Yonghui Hu, Hongxiang Ran, Honggang Wei

"A new PVM vertical ring high-gradient high-intensity permanent magnetic separator authorized by China Invention Patent ZL201110294866.4, which featured with vertical magnetic field structure was developed to dramatically save energy consumption and running costs compared with electromagnetic separators. The specific magnetic circuit design ensures PVM separator generating high magnetic field intensity as well as solving equipment large-scaling. The newly developed industrial PVM separator has been proved suitable for recovery of weak magnetic minerals or purification of non-metallic minerals benefiting from its high background and induction magnetic field intensity up to 0.8/1.5T, stable service performance and low running costs. The first ?1.5mm PVM separator has been applied in removing iron from quartz sand in Fengyang, Anhui, and ?2mm PVM separator will be installed to separate hematite. Industrial applications and tests proved that PVM separators could gain similar separation effects and especially save more than 80% of power consumption compared with the conventional electromagnetic high-gradient high-intensity magnetic separator, which will contribute a lot for energy conservation and environmental protection. The development of high gradient magnetic separator technology has played an important role in utilizing weak magnetic minerals, which has been widely used in many mining enterprises. The main forms of high-gradient magnetic separators include both of electromagnetic high-gradient and permanent magnetic high-gradient. The vertical ring high-gradient high-intensity permanent magnetic separator features with high magnetic field gradient, large processing capacity and never clogging, which has been widely used in recovering fine weak magnetic mineral and purification of non-metallic minerals[1-3]. However, electromagnetic coils excitation needs more energy consumption, and relatively high running costs and maintenance costs as a result of the complicated cooling system. So permanent magnetization of the electromagnetic magnetic separation equipment is a very important research direction at present. With the continuous improvement of resource utilization standard and efficiency requirements, high energy consumption of the electromagnetic vertical ring magnetic separator have been highlighted, which has affected the economic benefits of mining enterprises to a certain extent. In the aspect of high-gradient high-intensity permanent magnetic separation equipment, considerable researches have been carried out at home and abroad and many small-sized prototypes were developed yet never strode into large-scale industry applications[4-6]."

Jan 1, 2018

By N. A. Dementyeva

To improve gold recovery from preg-robbing carbonaceous ores a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon-in-leach (CIL) process for intensive cyanidation tailings and the recleaned concentrate was developed. The final flotation tailings are shipped to tailings disposal. Total gold recovery by the proposed technology from the ore with the head grade of 0.8 g/t was 83.9%. The gold loading onto the activated carbon from CIL process was 6.5 g/kg.

Jan 1, 2014

By F. Burat

At the present time, methods of mining and coal preparation produce tones of coal fines. The removal of water from these fines is necessary for economical and technological reasons. Supplementary processes that utilize different physical and chemical methods have been developed to in-crease the productivity of mechanical dewatering processes. Researches have shown that chemical reagents used along with conventional systems diminish moisture and increase the capacity and the yields of the dewatering method. In this study, the parameters of the vibrating screen (incline, frequency, feeding rate and screen size), the effects of the application of additional vertical mechanical vibration and surface active reagents (CTAB, SDS, Umectante B-70 and Kerosene) were investigated. At the end of the optimization experiments, 61.0% moisture was decreased to 42.3%. By keeping optimum conditions con-stant, the experiments have been conducted to determine most effective reagent. 41.2% moisture has been obtained with 5 g/t CTAB at the normal pH of the pulp, which were 7.25. By using vibrating screen with combination of the vertical vibrating mechanism, CTAB gave the best result of 40.7% moisture. Finally, the effect of increased surface area of the screen has been investigated and de-creased the moisture level to 38.7%.

Jan 1, 2014

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014