Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Audrey Boissier, Marie-Anne Camon, Cecile Cathalot, Yves Fouquet, Laurent Bignon, Arnaud Agranier, Ewan Pelleter, Sylvain Bermell, Florian Besson

INTRODUCTION In October 2014, on behalf of the French government, Ifremer, along with the International Seabed Authority (ISA), signed a contract to start a detailed exploration program for seafloor massive sulfide (SMS) deposits in the work plan located on the slow spreading Mid-Atlantic ridge (MAR). The contract has a fifteen-year lifetime and the related exploration program must include the outline of SMS deposits and a resource assessment, as well as detailed environmental base line studies in the contract area. The exploration for SMS deposits generally includes detection of hydrothermal plume anomalies, acquisition of surface and near-bottom geophysical data, sampling operations from the research vessel (e.g. dredges, cores), and dive operations. The environmental studies include, among others, short and long-term oceanographic measurements, water column studies, biodiversity evaluation close and far from SMS deposits, characterization of natural hydrothermal plumes and related sedimentation. The HERMINE research cruise held from March 13th to April 28th 2018 (R/V Pourquoi Pas?) was the first cruise dedicated to exploration of active and inactive SMS and to the quantification of natural chemical input to the water column. The HERMINE cruise strategy was built up around three main objectives: (i) regional exploration including the detection of plume anomalies and the research of SMS deposits, (ii) local exploration of a SMS district and (iii) integrated study of a natural hydrothermal plume. This 3-in-1 cruise required us to optimize the switch between dives and surface operations. Day-time was devoted to dive operations whereas night-time was mostly dedicated to CTD/Rosette operations. The Nautile HOV (Human Occupied Vehicle) was well suited to the working time schedule of the cruise because it was time efficient in shorter (i.e. < 10h) dives due to fast descent and ascent speed, fast submerged forward speed, high maneuverability and the ability to carry heavy science payload as well as large volume of samples. Regional Exploration The first seventeen days of the HERMINE cruise were devoted to regional exploration, i.e. the detection of new plume anomalies and the research of new sulfide mineralization in the French work plan (10 000 km2; 6 clusters).

Jan 1, 2018

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By Tobias Hens, Andrew Frierdich, Barbara Etschmann, Joël Brugger, Barrie Bolton

"Ferromanganese (Fe-Mn) nodules and crusts are prime targets for future deep-sea mining ventures due to their unusual enrichment of critical metals, such as Ni, Co, Cu, Ti, Te, Zr, Hf, Nb, Y, and REE. These metals are used in an ever increasing variety of high- and green-tech applications such as alloys, batteries for hybrid cars, fiber-optic cables, or liquid-crystal displays.1 Recovery and processing of these deposits will most likely be cost-intensive and require new solutions.2 Thus, innovative approaches towards the development of sustainable metallurgical processes represent one component that can positively affect the marine mining value chain. Dynamic mineral recrystallization of Fe- Mn oxide phases is a geochemical process that may have notable potential for future hydrometallurgical applications.Our research focuses on Mn oxides – potent trace metal scavengers with high sorptive capacity3 – and biogeochemical mechanisms that control Fe-Mn nodule and crust formation, alteration, and trace element enrichment. Biogeochemical redox cycling of Mn is characterized by microbial oxidation of aqueous Mn(II) to Mn(III,IV) oxides and (a)biotic reduction of these oxides to Mn(II)aq. During this cycling dissolved Mn(II) is in direct contact with solid-phase Mn(III,IV) oxides and can back-react via abiotic pathways (e.g., 4 and references therein). This results in continuous dynamic recrystallization of the Mn mineral substrate through coupled dissolution (trace metal release) – reprecipitation (trace metal incorporation) processes.4 We recently demonstrated in new experiments, that Ni is cycled during manganite recrystallization. It has been shown that, although Ni readily undergoes mineral-fluid repartitioning in the absence of Mn(II)aq, dissolved Mn(II) significantly catalyzes Ni exchange between solid phase and solution. Over a period of 50 days about 30 percent of the Ni atoms in Ni-substituted manganite (natural abundance composition) were exchanged with a 62Ni(II)aq isotope tracer at pH 7.5. Based on these outcomes we employed similar techniques to investigate the impact of dynamic recrystallization on Mn oxide phases in deep-sea ferromanganese nodules and crusts from three circum-Australian locations (South Tasman Rise, Lord Howe Rise, Coral Sea) and the Central Pacific Basin."

Jan 1, 2017

By R. W. Nesbitt

The TAG and Broken Spur hydrothermal mounds are located on the Mid Atlantic Ridge (MAR) at 260N and 290N (respectively). Both were initially discovered by exploratory work from surface vessels and both have since been investigated by submersibles. The discovery of TAG resulted from a NOAA Trans-Atlantic Geotraverse (Rona et al. 1975) which fortuitously sampled low temperature materials on the east wall of the MAR rift valley and follow up operations (Rona et al. 1986) located the high temperature (365°C) mound some 5km to the west. In 1994, ODP deep sea drilling (Leg 158) at over 3,500 metres of water recovered core to a depth of 150 m below surface (Herzig et al. 1998) and for the first time allowed a geological interpretation of an active mound. The Broken Spur mound was accidentally discovered in 1993 when sulphide fragments were observed on a deep-sea towed camera system (Murton 1993). Later that year, exploratory submersible dives by Alvin located the hydrothermal field and the area was again explored by submersible in 1994 and 1997. Despite the amount of work carried out, our geological understanding of the MAR mounds is limited. Much effort has gone into measuring fluid chemistry whilst practical difficulties have inhibited good geological mapping of the sulphide areas. It is clear from both TAG and Broken Spur that the mounds are not necessarily located in the areas of highest heat potential. Indeed, TAG is some 2 km from the rift valley axis and has been operational for several tens of thousands of years. Hence, heat availability is not a major consideration and the most obvious control is a structural one. Mapping on Broken Spur indicates a series of isolated vent-sulphide areas, concentrated around a minor graben. Their distribution, size and nature all indicate that they are residual parts of a much larger sulphide body which was at least the size of the present TAG field. The evidence is for a cyclical pattern of mound growth -mass wasting? rejuvenation and the Broken Spur mound appears to be in the rejuvenation stage of the cycle. Mound cyclicity must be related to the supply of hot water which itself is a function of the connectivity of fracture systems. Hence, we return to the theme that the major controls in mound development are structural ones.

Jan 1, 1998

By R. Moss

Gold and silver are important byproducts of mining volcanogenic massive sulfide (VMS) deposits. Both metals occur in VMS deposits ranging in age from the Archean to the currently forming massive sulfides found on the ocean floor. The gold- and silver-rich deposits on the modern seafloor are geographically diverse and occur in several different tectonic settings (Figure 1a,b) including seamounts (e.g. Franklin Seamount, Papua New Guinea), unsedimented mid ocean ridges (e.g. TAG and Snakepit, Mid Atlantic Ridge), sedimented mid ocean ridges (e.g. Escanaba Trough) and back-arc basins (e.g. Manus Basin, Papua New Guinea). Interestingly, the most gold- and silver-rich deposits are found in the back-arc basins of the western Pacific, commonly associated with differentiated volcanic rocks such as the dacite-rhyodacite suite at PACMANUS in the eastern Manus Basin. This suggests that different, or more efficient, mechanisms are concentrating precious metals in such back-arc settings. Such mechanisms may include leaching of volcanics enriched in gold (e.g. rifted arc crust) or silver (e.g. continental crust) and/or the introduction of gold into a hydrothermal system by a magmatic fluid. The gold content of modern seafloor precipitates varies from a few ppb up to a high of 54 ppm reported from eastern Manus Basin (1). The Jade Deposit in the Okinawa Trough has the highest silver contents with values up to 1.1% (2). Both gold and silver are preferentially concentrated in late-stage, low temperature precipitates with zinc-rich assemblages being favoured in most cases. Gold is found as relatively pure native gold and sub-microscopic inclusions in gold-rich deposits, but occurs predominantly as sub-microscopic inclusions and possibly as solid solution in the gold-poor deposits (3). Silver occurs as rare silver minerals such as acanthite and native silver in the silver rich Jade deposit (2), but more commonly in the silver-containing minerals tetrahedrite and tennantite, as is the case in the PACMANUS deposit. Tetrahedrite is also known to be an important host of silver in ancient VMS deposits (4). More abundant sulfides can contribute significantly to the silver balance. In the silver-poor deposits at 21 N East Pacific Rise, silver is contained entirely within chalcopyrite, isocubanite, pyrite, marcasite, sphalerite/wurtzite and galena. In this case silver may be present as sub-microscopic inclusions of silver minerals or in solid solution.

Jan 1, 2011

By Seung-Kyu Son

Environmental properties of the northeast Equatorial Pacific along 131.5 degrees west, between 5 degrees and 13 degrees north latitude, were investigated in association with changes in water column structures during the summer seasons of 1998 and 1999. Climatic disturbances such as El Nino and La Nina, should have affected this area during the study period. In 1998, a thermocline where temperatures rapidly decrease with depth, was formed at 90~110 m water depth. However, in 1999, a very fluctuating thermocline was observed with latitudes. As a result of changes in the water column structures, biological and chemical environment also showed fluctuation parallel to the changes in other physical parameters. Inorganic nutrient depleting areas, especially for nitrate+nitrite and phosphate, or oligotrophic regions were extended down to approximately 100 m depth, which coincided with the surface mixed layer depth. In the euphotic zone, depth integrated nitrogen (N) and phosphorus (P) values were 34 g-N/m2 (grams of Nitrogen per square meter of sea floor), 7 g-P/m2 in 1998 and 130 g-N/m2, 18 g-P/m2 in 1999, respectively. The results indicated that nitrogen (96 g-N/m2) and phosphorus (11 g-P/m2) are supported by up-welling and down-welling phenomena with convergence and divergence in the study area. Biological parameters in the water columns were largely determined by the physico-chemical environmental parameters. Subsurface chlorophyll maximum layers were coincided with the formation of seasonal thermocline. Copepods were the dominant group of zooplankton community at three sampling stations (N5, N6, N10) terms of abundance, which was the same results of previous surveys for the past 3 years. Among copepod populations, Oncaea sp., Oithona sp. Clausocalanus sp., Acarocalanus sp. and juvenile copepodites were dominant Appendicularians, foraminiferans and radiolarians were also dominant. To investigate diel vertical migration pattern of zooplankton, repeated samplings from the water depth of 0~50m and 50~200m were conducted at KODOS (Korea Deep Ocean Study) area before and after sunrise. Zooplankton abundance was slightly higher after sunrise than before sunrise in the surface layer. Chlorophyll-a concentrations were relatively low as the concentration of sediment increased in most experiments possibly due to a decrease of grazing pressure of microzooplantkon such as ciliates, which is the efficient grazer on small-sized phytoplankton. Because copepod predation on microzooplankton may be prevented by the high concentration of sediment, resulting in lower grazing pressure on small-sized phytoplankton. The results obtained during the baseline study as a part of KODOS project since 1998.

Jan 1, 2001

The Brothers hydrothermal system is host to two very contrasting vent fields and to date, is the only known example of this kind for any submarine arc volcano in the world. Firstly, there is the NW caldera field. It is perched on the caldera walls and is up to 1,200 years old, and represents a more ?mature? system dominated by water/rock interactions, though there is also evidence for magmatic contributions to the hydrothermal fluids. It is host to relatively high temperature (~300°C), focused venting of metal-rich fluids. Large Cu- and Zn-rich sulfide chimneys occur at this site, with high concentrations (up to 90 ppm) Au apparent in some chimneys. Vent fluids of the NW caldera site show sub-seafloor phase separation is occurring at this site. Silica concentrations in these vent fluids are consistent with the vent fluid temperatures. Secondly, there is the cone vent field that is much younger, and which sits atop the summits of a main cone (the Upper cone) and an adjacent satellite cone (the Lower cone) that occur inside the caldera, near the southern caldera walls. This field is dominated by S-rich vents with vent fluids more diffuse, lower in temperature (<120°C), very gassy and acidic (to pH 1.9), and relatively metal-poor. Fluids of the cone site have Mg and SO4 concentrations higher than seawater values, indicating these ions have been added to the hydrothermal fluid and are not being depleted via normal water/rock interactions. Variability occurs between the two cone vent fields, with the diffuse discharge observed at the Upper cone volumetrically small and chemically different from the Lower cone. For example, from the vent fluid Mn, Li, Rb, and Cs concentrations, it is apparent that the Lower cone has experienced a lower degree of water/rock interaction (i.e., more reaction) than the Upper cone. Vent fluid pH is higher for Lower cone, consistent with more reaction and neutralization of acidic gases. Fe/Mn is lower at the Lower cone due to decreased Fe solubility at the higher pH. The lowest pH sample (1.9) is from the Upper cone that has 39.4 mmol/kg of SO4, consistent with input of magmatic SO2 and disproportionation to sulfuric acid and S or H2S. Thus, the Upper cone site could be interpreted to have a shorter reaction path and residence time between the point of magmatic degassing and the seafloor venting than the Lower cone site. Isotopic compositions of the NW caldera and cone vent fluids show evidence for magmatic water with negative dD and d180 values, while 3He/4He values show the Brothers hydrothermal system has shifted towards more magmatic conditions over the past several years with both sites affected by magmatic events. Similarly, vent fluid sulfide d34S values and those for sulfide minerals from NE caldera chimneys also indicate disproportionation reactions involving magmatic SO2. Minerals such as chalcopyrite, bornite, chalcocite, covelllite and euhedral grains of hematite occurring in high temperature chimneys from the NW caldera site are consistent with a more oxidizing, magmatic fluid, while bulk sulfide geochemistry data show evidence for a higher temperature suite of elements (e,g., Mo, Co, Se) associated with Cu-rich chimneys. Gold mineralization occurs in these high temperature chimneys and is associated with the most recent deposition of high concentrations of Cu, where d34S values are most negative. Geophysical evidence suggests that the top of a magma chamber occurs ~2.5 km below the caldera floor, beneath the cone site in the SSE quadrant of the volcano. Very low velocities of <1 km-2 are seen in the seismic data between the magma and the seafloor, and are indicative of gas release. Harmonic tremor data provide evidence for a 500 m pipe-like ?conduit? located above the magma chamber (and below the cone), linking it with the overlying hydrothermal system, providing a mechanism for magma-derived metals to enter the hydrothermal system under the cone site. The NW caldera and cone sites are considered to represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members.

Jan 1, 2010

By Jae-Hyung Park

Since the Industrial Revolution, the land resources have been decreased rapidly as the industrialization. And this phenomenon brings to our mind an interest in deep-sea resource(manganese nodule). Hence, Korea has been participated in the development project of exploiting manganese nodule since 1983. Hwang and cho(1998) studied the economic efficiency evaluation of manganese nodule carrier. But they used the TAMU(Texas A&M University) model, and assumed deadweight and velocity of bulk-carrier. If we use some optimization technique, more economic manganese nodule carrier can be selected and evaluated without limited assumption. In this study, we evaluated the economic efficiency of manganese nodule carrier using genetic algorithms(GAs).

Jan 1, 2003

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By Tetsuo Yamazaki

Manganese nodules, seafloor massive sulfides, and cobalt-rich manganese crusts in deep-sea areas have been considered as future metal sources (Mero, 1965; Halbach, 1982; Lenoble, 2000). Manganese nodules were the first recognized deep-sea mineral resource and many efforts concentrated on the R&D of mining systems (Welling, 1981; Herrouin et al., 1989; Yamada and Yamazaki, 1998) and assessment of environmental impacts (Burns et al., 1980; Foell et al., 1990; Yamazaki and Kajitani, 1999). No mining venture, however, has been active for this potential resource. The reason is that the rate of world economic growth has been slower than anticipated in 1960s. During the 10 year period of 1994-2003 (Fig. 1), on the other hand, there was about a 33% increase in the world copper demand. Of that increase, about 60% was consumed by China. Most of China?s increased copper demand took place over the final 4-5 years of that period. The growth is expected to continue for several years, and in 10 years or sooner the same situation is expected for India. Copper is the third metal in global demand, but its small abundance in the Earth?s crust is not well recognized (Table 1). From the production rate and the abundance, a copper shortage, or crisis, has a high probability than the other metals. Japan has no domestic copper resources and needs a counter measure for this potential coming copper shortage. Fortunately, Japan has a manganese nodule mining claim in the Clarion-Clipperton nodule field, Kuroko-type massive seafloor sulfide deposits in the Okinawa Trough and Izu-Ogasawara areas, and cobalt-rich manganese crusts around Okinotori-Shima and Marcus Islands. We need to re-evaluate their potential as copper resources and to realize their development.

Jan 1, 2005

By T. Semkova, G. Cherkashov, V. Rashidov, L. Anikeeva, G. Gavrilenko, G. Glasby

The Kurile Arc consists of at least 100 submarine volcanoes and 5 submarine calderas located mainly in the rear arc (Figure 1). The arc is seismically very active, particularly in the south, and is characterized by extensive volcanism and hydrothermal activity. At least one subaerial volcano on the arc (Medvezhy located on Iturup island) has an extremely shallow magma chamber and is intensely active.

By G. A. Tret’yakov, V. A. Simonov, I. Yu. Melekestseva, V. V. Zaykov, N. N. Ankusheva

The Kyzyl-Tashtyg massive sulfide polymetallic deposit is situated 120 km north-east of Kyzyl (the capital of Tuva Republic, Russia). It is located in the Ulug-O volcanic zone which is interpreted as the northern segment of the Kaa-Khem rift in Sayano-Tuva marginal sea, one of the Paleoasian Ocean margin (Fig. 1) [Zaykov, 2006]. Since its discovery in 1946 the deposit has been studied by many researchers. Significant information was published by Kuzebny et al. [2001] and Zaykov [2006] who proposed volcanogenic-sedimentary genesis. A single reference in English about Kyzyl-Tashtyg is available [Herrington et al., 1999].

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By Ian J. Graham, Cornel E. J. de Ronde

New Zealand lies astride a convergent plate boundary that extends north-eastwards from the Taupo Volcanic Zone (TVZ) to Tonga. This boundary is marked by the Kermadec arc, c. 1200 km of which falls within New Zealand’s EEZ, and which is host to numerous volcanic edifices both on the arc and in a zone immediately behind the arc to the west. In 1999, thirteen volcanic centres in the southern 260 km of the arc were surveyed for their hydrothermal plumes with seven of them discharging vent fluids into the surrounding ocean. Three of the seven volcanic centres have had mineralised rocks recovered from them during dredging and submersible operations, namely Brothers, Rumble II West and Clark. Presentday plume data combined with mineralogical evidence indicate that the vent sites at Rumble II West and Clark are waning, although the presence of Cu-rich sulphides in samples recovered from Rumble II West suggest there may be a massive sulphide (Cu-Zn-Pb-Ba ± Au) deposit located within the caldera. Brothers volcanic centre is host to the largest polymetallic mineral deposit discovered along the Kermadec arc and has numerous, up to 7 m tall chimneys within a c. 600 x 200 m area located on its NW caldera wall. Geochemical data indicate that concentrations of base metals are variable and depend critically on sample type. When combined with mineralogical and plume data, this indicates addition of a magmatic fluid component to the vent fluids.

Aug 24, 2006

By T. Kuhn

The Logatchev hydrothermal field is situated on the east inner flank of the rift valley of the MAR at 14°45?N and is hosted by serpentinized peridotites and minor gabbronorites while basalts are subordinate. Hydrothermal precipitates recovered from the Logatchev field during a recent R/V Meteor cruise include massive chalcopyrite chimneys, massive pyrite crusts, silicified breccias, abundant secondary Cu-sulfides, red jaspers, abundant Fe-Mn-oxyhydroxides as well as atacamite and Mn-oxides (Kuhn et al., 2004). Previous results of hydrothermal fluid studies in the Logatchev field are somewhat at odds with theoretical models of ultramafic-seawater reaction. Butterfield et al. (2003) suggested that the Fe component of orthopyroxene plays the more important role compared to olivine in ultramafic-hosted hydrothermal systems. This consideration is supported by the recovery of large amounts of Opx-rich gabbronorites and orthopyroxenites in the Logatchev field (Kuhn et al., 2004). A possible tool to constrain the contribution of the different rock types (ultramafics, mafics, MORB) to a seafloor hydrothermal system is the systematic analysis of 187/188Os ratios of the host rocks as educts and the sulfides as products. For instance, abyssal peridotites mainly display low 187/188Os ratios (<0.127); in contrast MORB and gabbronorites have radiogenic ratios of >0.13 (Snow and Reisberg, 1995), orthopyroxenite has ratios of about 0.174 (Büchl et al., 2002) and seawater has an ever higher 187/188Os of about 1 (Sharma et al., 1997). Therefore, massive sulfides predominantly leached from ultramafic rocks should have Os isotopic ratios plotting on a mixing line between the ultramafic rocks and seawater (in a 187/188Os vs. 1/Os diagram), whereas those derived from MORB, gabbronorites and/or orthopyroxenites will be plotting on different mixing lines.

Jan 1, 2004

By Peter E. Halbach, Andreas Jahn

Co-rich hydrogenetic ferromanganese crusts are typical marine interface products of growth processes taking place on sediment-free substrate rocks on the seafloor. They grow very slowly and preferentially in water depths below the oxygen-minimum zone (OMZ) and have so far been found even in water depths of up to more than 5000 m, i.e. also below the calcite compensation depth (CCD); these deep ferromanganese crusts are particularly rich in Fe. It is assumed that the O2-minimum zone is the most important source layer of dissolved manganese, the decomposition of fecal pellets here also contributes to this Mn-budget. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical as well as a surface-chemical mechanism. Microbial mediations can be assumed, in particular since steps of redox-reactions are involved. The two main components of the hydrogenetic substance are hydrated d-MnO2 (vernadite) and x-ray amorphous Fe-oxyhydroxide, both of which are intimately intergrown with each other forming the extremely fine-grained hydrous oxidic material. In seawater, elements occur as dissolved hydrated ions or as inorganic as well as organic complexes which, in general, have either a positive or a negative surface charge depending on the pH of the respective marine environment. These complexes form hydrated colloids that interact with each other or with other dissolved hydrous metal ions. The main agent to oxidize the dissolved Mn2+ ions is oxygen, transported upwards from deeper water by turbulent eddy diffusion and turbulent rise processes at seamount slopes.

Jan 1, 2017

By Cheong-Kee Park

Since 1983, Korea Ocean Research and Development Institute (KORDI) have performed surveys on deep-sea mineral deposits in various areas with respects to their occurrences in Pacific ocean including manganese nodules in the C-C area of Northeast Pacific, Co-rich manganese crusts in various seamounts of West Pacific and hydrothermal sulfide deposits in back arc basins of Southwest Pacific. Among the results of these activities of KORDI, remarkable things were the registration as a pioneer investor in 1994 through the Government of Korea and the accomplishment of relinquishment on the allocated area in 2002 according to the relevant regulations. KORDI is faced to handle detailed surveys to select the optimum mining sites in the allocated area of 75,000 km2 and environmental studies to meet the requirements of the regulations or recommendations of the ISA. In respects of future exploration strategies, it is considered that methods and tools of previous exploration activities should be changed to the highly advanced technology. Establishment of an advanced exploration system and actual practice in appropriate areas become one of important tasks of KORDI in exploring deep-sea minerals, particularly manganese nodules. A technical strategy for future detailed surveys in the allocated area is realization of simultaneous and precise data acquisition on bottom information, such as variations of microtopography, nodule distribution, and transparent layer thickness of sediments in relatively small area (10 km x 10 km) representing certain specific regions, by high resolution survey technology. It would be not only a challenge for new exploration system in deep-sea environment, but also a mission for deep seabed mining venture.

Jan 1, 2003

By Hyung-woo Kim

This paper concerns about steering characteristics of pilot mining robot, named MineRo II, crawling on extremely cohesive soft soil using dynamic simulation software. The MineRo-II for deep-seabed manganese nodules, which aims at the use for pilot mining test, was manufactured in 1/5 scale of commercial mining capacity (see Fig. 1).

Sep 14, 2011

By D. S. Cronan

Studies on polymetallic manganese nodules and Co-rich crusts in the EEZ&apos;s of the Cook, Line, Ellice and Phoenix Islands between 0-20°S show that Ni and Cu reach their greatest combined abundances of over 2% between 2-8°S on the southern margin of the equatorial zone of high biological productivity, as a result of biological fluxing of Ni and Cu to the nodules at and just below the CCD. By contrast, Co reaches it greatest abundance of 0.6% south of 8°S in nodules on non-biogenic clays well below the CCD where little biological Co supply is likely. Nodule abundances are greatest (up to 30kg/m2) in the Co-rich area in part due to AABW flow, giving highest overall metal quantities per sq meter in the nodules there, particularly of Co. There are approximately 110 x 106 tonnnes of combined Ni plus Cu plus Co expressed as Ni equivalent in Cook Islands EEZ nodules, approximately 12 x 106t. in Phoenix Islands ones, and approximately 1.4 x 106 t. in Ellice Islands ones, in areas of greater than 5kg/m2 nodule abundance. In the Co-rich crusts, Co averages about 0.7% and crust thickness about 1.6cm, both related to metal fluxes in and adjacent to the 02 minimum zone in association with which both maximum thicknesses and Co grades occur. Within the Cook Islands permissive area there are about 930 x 103 t. of Co and 630 x 103 t. of Ni in crusts, in Phoenix Islands crusts there are about 69 x 103 t. of Co and 55 x 103 t. of Ni, and in Ellice Islands crusts there are about

Jan 1, 1989