Search Documents

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By F. W. Liang

The geology of pearl River estuary belongs in strong weathered rock quaternary geological systen, so the conditions are complication. Since 80's we built the first deepwater wharf of Shenzhen chiwan port which has 3 berths of 10000 dwt, We have built 3 berths for vessels of 40000 dwt both in Shekou Port and Chiwan port. The berths for carriers of 10000 dwt in Yantian Port of Dapeng Bay are constructing now. In the five years, We built more than 20 deepwater berths of 5000 dwt to 40000 dwt. This paper will introduce how to solve the difficulties of the complex geological conditions and how to use the new fashion construction. We will reduce the period of engineering construction and get good quality and make a good beginning of rapid development of port construction in ShenZhen Special Economic Zone.

Jan 1, 1991

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010