Search Documents

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

By Shigeru Sarata

A wheel loader is one of the main loading machines in open pit mines. The authors have been conducting research and development on autonomous operation of loading by a wheel loader. The most common loading method by a wheel loader is the ?V shape? path method. The loading operation consists of cycles of scooping from the pile, traveling to the dump truck, loading on the dump truck and return traveling to the scooping point for the next cycle. The traveling path includes a switchback in the middle of the path. The moving direction of the loader is changed at the switchback point. From observation of V shape path loading operations by experienced human operators, it seems that they control the bucket position between the scooping point and loading point on a shorter path for higher productivity. A new path planning method is proposed this paper, whereby a point on the center of the tip of the bucket is controlled moving from the initial point and the final point. The motion of the controlled point is generated by the wheel steering the wheel loader. The controlled point is moved along the direction to the final point; however, the motion and mechanism of wheel loader have restrictions, such as the velocity of the loader, the steering angle, and the steering angular velocity. Because of these restrictions, the path of the controlled point is not a straight line between the initial and final points. When this control method is applied between the scooping and the dumping points directly, the planned path is not stable in the leaving wing of V shape path. Therefore, the initial position of the wheel loader is set at the switchback point, then two approach wings to the scooping and the dumping points are made. The whole planned path is obtained by connecting the two paths. The shape of the planned path is strongly affected by the position of the switchback point, as well as the scooping and the dumping points. By simulation of path planning at different switchback points with the combination of the scooping and the dumping points, the paths for more effective loading are determined. The results of the simulation are presented in the paper.

Aug 1, 2013

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By Stanley Davidson

Introduction The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oyster-shaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than fifty years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis. The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass which, however, is here concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling. The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proven to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the "Edison' shaft never reached bed-rock.

Jan 1, 1946

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By P. Van Marcke, X. Sillen, G. J. Chen, I. Troullinos, A. Dizier, J. Leysens, X. L. Li, J. Verstricht

"In Belgium, Boom Clay is considered as one of the potential host formations for the disposal of the High Level radioactive Waste (HLW). The URL HADES at 223 m depth at Mol site was constructed in order to study the feasibility of HLW disposal in Boom Clay. Since 1995, the URL R&D programme has focused on large scale demonstration tests like the PRACLAY experiment.The PRACLAY in-situ experiments include a set of three tests: The gallery and crossing test, PRACLAY Heater test and PRACLAY seal test. The main aim of the Heater test is to study at a large scale the thermal impact of a HLW repository on the host rock. The test is housed in the PRACLAY gallery. A hydraulic seal, made of compacted swelling and low permeable bentonite annular ring was installed at the intersection between the heated and the non-heated part of the gallery. The primary objective of the seal is to provide undrained hydraulic boundary conditions for the Heater Test.The PRACLAY gallery was constructed in 2007 and the hydraulic seal was installed in 2010. The bentonite is hydrated by natural and artificial process. The swelling, total pressure and pore pressure of the bentonite are continuously measured and analysed by numerical simulations to get a better understanding of this hydration processes. The performance of the seal is tested systematically by means of gas injection breakthrough tests and permeability tests at interface bentonite / Boom Clay and in the Boom Clay around the seal.The PRACLAY Heater will be turned on at the end of Oct. 2014, since a sufficient seal swelling has been attained to fulfill its role for the PRACLAY Heater test. This paper will focus on the PRACLAY Seal test: How we understand the process behind the hydration of the bentonite and how we test the performance of the bentonite seal."

Jan 1, 2015

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By Guichao Wang, Geoffrey M. Evans, Graeme J. Jameson

"In this paper we present a new method for studying the detachment of particles from bubbles in a rotating turbulent eddy. The eddy is formed in a wall cavity in a two-dimensional water tunnel with transparent walls. When water flows through the tunnel, a vortical flow field develops in the cavity. The properties of the eddy can be modulated by changing the free-stream velocity of the water in the tunnel. Bubbles are pre-loaded with one or more particles in a fluidized bed flotation device located beneath the vortex cavity. Loaded bubbles are released one at a time into the cavity, and the motion of the bubbleparticle aggregate is studied using a high-speed video camera. The diameters of the particles and the bubbles, and the number of particles initially attached to the bubble, can be varied. The trajectories taken by the bubbles are quite complicated. In some cases, the bubble moves to the centre of the eddy, and particles rotate around its axis. If the rotational speed is sufficient, particles may detach due to centrifugal force. However, other modes were observed, including inertial detachment due to rapid changes in direction of the surface of the bubble, because of changes in trajectory of the bubble as a whole, or because of pulsations and oscillations of the bubble surface. Clusters of bubbles held together by particles were seen to form and reform. In the traditional explanation for the detachment of particles in flotation cells, it is assumed that particles detach from bubbles rotating in an eddy due to centrifugal force (Schulze, 1977). Although the conditions assumed in Schulze's theory may exist, it is only one of a range of phenomena that can lead to the detachment of particles from bubbles in a turbulent vortex.INTRODUCTIONThe recovery of particles by flotation methods is dependent on the particle size. The recovery in the existing flotation machines reaches a peak for particle size, typically in the range of 20 to 100 µm. This size range varies as a function of the particle’s properties (type and composites). For coarser particles, the recovery drops very quickly (Gaudin, Groh & Henderson, 1931; Jowett, 1980). If the upper size limit can be increased for flotation, dramatic savings in the grinding energy can be achieved."

Jan 1, 2016

By D. J. Parker, G. B. Tupper, I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

By B. Jakovljevic, M. D. Soderstrom, T. McCallum, A. J. Quilodrán

Cytec has developed a new organophosphorus based solvent extraction (SX) reagent for rare earth separations. The new product, CYANEX® 572, has been formulated to allow efficient extraction while minimizing the strip acid requirements. The optimization of formulation strength is expected to significantly reduce the operating costs of these circuits. Modeling capabilities for CYANEX® 572 (similar to those used successfully in Cu and Co/Ni SX) have also been developed to aid in the design and optimization of the SX circuits. Simulations will be shown comparing CYANEX® 572 to a traditional rare earth extractant.

Jan 1, 2014

By Alan L. Sangster

Auriferous, bedding-parallel veins occur in zones of carbonaceous, argillaceous and sulfidic turbidites in the Lower to Middle Cambrian sandy flysch of the Goldenville Formation. The 0348 values for vein and wall-rock arsenopyrite and pyrrhotite, and for regional pyrite and pyrrhotite, are highly positive. The values are similar to those from Cambro-Ordovician sediment-hosted deposits of other types, and display trends that increase upward in the stratigraphic sequence. The similarity in composition of vein and wallrock sulfides indicates a seawater-sulfate sourCe for sulfur, derived from the enclosing rocks at the time of vein formation. The upward increase in ?34S values is consistent with closed system sulfate reduction in the anoxic portion of a stratified water-colurnn. Published ? 13C and ? 18() values for Meguma Group vein carbonates are unlike those of other gold-vein carbonates, but are similar to those of diagenetic-metamorphic carbonates from the Meguma Group and elsewhere. These data indicate that the source for the vein-related sulfides and carbonates may be the host strata; possibly the arsenic and gold were derived from the same source.

Jan 1, 1992

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By Richard W. Hutchinson, Christopher Osterman

The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and footwall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fIne grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfIde piercement structures and the footwall Cu-PGE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994