Search Documents

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Lorant B. Geller

Sixteen miners died tragically at the Paymaster gold mine at Timmins, Ontario in February, 1945, when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (Investigations, 1947) aimed at avoiding future disasters of this kind. One consequence was the development, and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the nondestructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990 and 1992, Geller and Kitzinger, 1991, Geller et al., 1993). Since the mid-1990s particular attention was paid to the design and operational results obtained from the computer- controlled portable MagnographJ II wire rope tester (Geller et al., 1995 and 1998). In the present article the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the PermaScanJ testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remotecontrolled instrument described in this paper has now been in operational use for more than 4 years.

May 1, 2003

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By B. Adams, T. Angelov, G. Sasov, D. Steinhilber, A. L. Tsekov, S. Neufeind

A complementary ion exchange/solvent extraction process for the recovery of copper from low- grade ores is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tons per year. Compared with conventional SX/EW operations, this technology makes the exploitation of low-grade copper ores economically attractive, due to reduced operational and capital expenditures. Furthermore, the additional Lewatit® ion-exchange installations diminish the volumes of harmful organic substances in the following SX step and minimise the risks associated with the handling and usage of these chemicals, such as environmental pollution or fires. Finally, the significantly diminished quantities of liquids for the SX operation have a tremendous effect on the footprint of the plant (ca. 50% less) thereby leading to a reduction of capital expenditures. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase. After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.

Jan 1, 2019

By B. A. Kjarsgaard, C. J. Mwenifumbo

"Abstract - Natural gamma-ray measurements were made in the GSC Smeaton drillhole as part of the borehole geophysical classification of kimberlite pipe 169. In addition, forty samples of Cretaceous sediments (shales, siltstones, and sandstones) and thirty-five kimberlite samples, selected from the drill core, were analyzed for major and trace elements. These elements included potassium (K), uranium (U), and thorium (Th), which are the main naturally-occurring radioactive elements.Different phases of the kimberlite, and the Cretaceous sediments which show variations in the gamma-ray activity, can be easily delineated on the gamma-ray logs. The gamma-ray logs indicate that the radioactivity in the kimberlite derives mainly from Th, and, to a lesser extent, U. Most of the kimberlite units are enriched in Th and U relative to the Cretaceous sediments, and these radioelements are mainly hosted by accessory apatite and perovskite, and minor zircon. Potassium concentrations are low in the kimberlite. The higher K concentration in the sediments clearly distinguishes the Cretaceous sediments from the kimberlite.The U/K and Th/K ratios show important and distinct differences between the two major types of volcaniclastic kimberlite. Kimberlite lapillistones have higher U/K and Th/K ratios than the olivine crystal tuffs. Furthermore, standardized U/K and Th/K geophysical logs can be used to separate marine reworked olivine shoreface sands from other shallow marine sediments that contain kimberlitic detritus. The identification of different phases and/or stratigraphic facies of kimberlite on the basis of radioelement distributions means that gamma-ray spectrometry can assist exploration, particularly in regard to diamond grade distribution."

Jan 1, 1999

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By C. Díaz, A. D. Dalvi, C. E. O'Neill

"Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters. IntroductionReduction of sulphur dioxide emissions has been a long-standing endeavour at Inco. At the company's Ontario Division, as shown in Figure 1, sulphur dioxide emissions were reduced from about 2 million to 685 000 tonnes per year over the period 1970-1985. Most of this impressive improvement was the result of a sustained research effort which led to increased rejection of pyrrhotite from the ore during milling while maintaining an acceptable nickel recovery. Between 1970 and 1985, the combined grade of the separate nickel and copper concentrates feeding the Copper Cliff Smelter increased from about 10070 to about 'lIJ0J0 Cu +Ni and the combined S/(CU +Ni) ratio decreased from about 2.8 to 1.65."

Jan 1, 1994

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP's"" include Digital Power Meters (DPM's) and Power Demand Controllers (PDC's) as well as other specialized instrumentation packages such as Mini RTU's."

Jan 1, 1991

By Margarete Kalin

Mine Waste Management ?Reduction of Sulphideoxidation or inhibiting weathering of rocks Geologist - broken or ground rocks Hydrologist - sources of contaminants Mining engineer - waste sites Consulting companies - income units People - Ugly, bad, dead Ecological Engineer Landscapes which contain building blocks of an emerging ecosyste

May 1, 2013

By T. R. Eger

The Load-Haul-Dump (LHD) vehicle is a trackless, free-steered vehicle used in underground hardrock mining to move large quantities of ore/rock to haulage trucks, ore dump locations, or crushing stations. The purpose of this paper is to show, through case study examples, how principles of human factors can be applied to improve the overall design of the LHD vehicle to enhance line-of-sight (LOS), improve posture and decrease whole-body vibration exposure (WBV). Vehicle modifications (larger cab windows, lower engine profile, smaller buckets, angled radiator profile) can lead to improved line-of-sight. The use of secondary viewing devices, such as cameras, can also improve line-of-sight and allow the operator to adopt a more neutral sitting posture. Seating systems that are suited to the underground mining environment can result in vibration attenuation and less vibration transmitted to the LHD operator. The connection between vehicle design, line-of-sight and driving posture needs to be considered in order to continue to improve the design of the LHD and enable the operator to work in a neutral posture with minimal vibration exposure. Changes leading to improved line-of-sight, vibration reduction, and a neutral sitting posture will lead to fewer LOS related accidents and decreased risk factors for musculoskeletal injury.

Aug 1, 2013

By Gunther F. Leichtle, James A. Finch, Colin A. Hardie, Cesar O. Gomez

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibers for use in newsprint. The mineral processing group at McGill University in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network) has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University's flotation column test work at a Quebec wastepaper recycling facility.IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world's largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and U.S. municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World's solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity.A key to the success of producing quality recycled fibers from wastepaper is the deinking technology. The production of tissue papers, paper towels and newsprint requires regenerated fibers which are substantially free of ink particles. Of the various options available, mineral processing techniques can offer the most economical, environmentally acceptable and versatile strategies (Yoon, 1993). Today, it is recognized that flotation is one of the most effective processes for removing ink particles in the production of a high quality product. In a collaborative program with the Pulp and Paper industry, the mineral processing group at McGill University has adapted column flotation technology for this purpose. This article will describe the typical process of deinking from a mineral processing point of view (Part A). It will also present some results from McGill University's flotation column test work at a nearby paper recycling facility (Part 8)."

Jan 1, 1998

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By Robert B. Parsons

"No Canadian or his family is likely to escape the effects of proposals for pension reform tabled on October 9, 1986 by Finance Minster Michael Wilson. New tax rules are proposed for Registered Retirement Savings Plans (RRSPs), company pensions, and other forms of retirement plans. Draft legislation is expected to be released in the first half of 1987.IntroductionOver two years ago on February, 15, 1984, Mark Lalonde, then Finance Minister, tabled two White Papers. The first, Action Plan for Pension Reform, proposed improvements to the public pension system and increases in the minimum pension benefits standards to be mandated by the federal government. Since then changes have been made to the Old Age Security, Guaranteed Income Supplement and Canada Pension Plan programs. Also, benefits provided under pension plans subject to the federal Pension Benefits Standards Act have been improved significantly.The companion paper, Building Better Pensions f or Canadians, proposed to standardize and, in many cases, improve retirement savings through private plans by revising the tax rule s. The tax proposals in the Notice of Ways and Means released by Finance Minister Wilson on October 9. 1986 implement, with modifications, the tax treatment of retirement savings originally proposed in the May 1985 budget in response to that second paper."

Jan 1, 1987

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011