Search Documents

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By M. Hamamoto, M. Furuta, S. Tanaka

The Tamano smelter and refinery has expanded its production from 228kt/y to 260kt/y since 2006. It was not a big jump, but efficient and economical improvements were executed. These were not only de-bottlenecking and modernization of the smelting plant, including the acid plant, but also additional processes were commissioned, e.g. slag cleaning furnace and steam dryer. On the other hand, a conversion to permanent cathode process in the #2 tank house made the biggest impact on production efficiency for the refinery plant. In order to overcome the drastic change of copper business, although each scale is not so big, continuous improvements are very important to survive. This paper mainly describes the recent improvements of the smelting plant.

Jan 1, 2007

By Keith Spence

"The notion of ""value"" has always been a subjective and contentious issue. Indeed, Value is in the eye of the beholder. There are varied methods and practices for valuing property, as there are industries in which they are applied. For example, there are ""replacement value"", ""insurance value, ""salvage value"", ""appraised value"", ""book value"" and ""fair market value"", to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered, are included the following: the Discounted Cash Flow Approach, the Cost Approach, the Option Pricing Approach and Market Comparables Approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIMVal committee expects that its final report will form the basis for a standard Canadian Code for the valuation of mineral properties."

Jan 1, 2003

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

By Enrique Rubio

Several mining operations are currently evaluating the feasibility of changing their mining method to Block Caving. There will also be several deep low-grade ore bodies that will face the need to go underground in following their ore to depth. There are two main reasons why Block Caving is attractive: firstly, it offers the lowest operating costs amongst all the mining methods; and secondly, it is truly a massive mining method, offering the highest potential production capacity. Despite its longstanding popularity, there are still significant components of the method that are not clearly understood. Also, the lack of availability of key geomechanic information still presents a major obstacle to developing mine planning and production scheduling. There are several key issues in block caving that can make it feasible such as cavability, fragmentation, stresses will condition the way that a block caves and the way that material is drawn from the draw points. Consequently Block Cave mining method is a good example where the ore body has to be related to design and mine planning. The concepts of dilution, draw control as well as sequence definition are reviewed in this paper to illustrate the idea of integration. There have been some examples of mines where some of the components of mine planning have not been integrated causing a disaster in terms of economics or safety. Different layouts configurations might give a different result in the planning of the mine

May 1, 2002

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By J E. McMynn

The development of the Granduc mine presents a number of problems which are peculiar to its location and surrounding terrain. Because the development tunnels portal onto an area which is covered by an extensive glacier, and the mountain-side is subjected to dangerous snow slides, it was decided to construct an underground powerhouse to supply the necessary electric power and compressed air. This paper deals with the special problems inherent in the design and -construction of an underground plant. It involves the installation of diesel-electric generating equipment having an aggregate capacity of 1,050 kw.,and of air compressors with a total capacity of 2,400 cfm. Items dis-cussed include the selection of equipment to meet site conditions, the ventilation and cooling of the underground room, and the protection of personnel and equipment from explosions and fire. A short discussion on the automatic supervisory and alarm installation is also included. THE Granduc mine is located 135 miles north of Prince Rupert and 25 miles north of Stew-art. This seems quite accessible, mileage-wise, but, due to mountains,

Jan 1, 1963

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By Daniel L. Cluff

The Canadian mining industry needs to find viable alternatives to the conventional cemented pastefill/hydraulic methods of backfilling open stopes for underground mines located within a permafrost zone. The harsh environment and the isolated location of a mine north of 60° impose additional challenges to standard backfill methods and opportunities to the technological and operational issues related to the use of frozen fill. Underground open stoping mining methods require the placement of fill material to enable the controlled recovery of ore from secondary and tertiary stopes. The typical design of the fill material requires the specification of inert material, water and binder. The permafrost conditions provide the additional parameter of subzero temperatures for backfill design and process control. The paper presents the results of an experimental field study, using large size samples, to determine the strength capacity of frozen backfill. The experimental work was performed utilizing rockfill and tailings material with moisture content consisting of water and ice crystals. Preliminary results indicate that the mixture of rockfill, tailings and moisture, develops strength that meet the demanded requirements for open stoping. A thermal equilibrium modelling analysis is presented in the paper.

May 1, 2008

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company's share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company's working capital is approximately $1,500,000.

Jan 1, 1963

By R. C. Carne, R. J. Cathro

"Most of the recent large discoveries of zinc, lead and silver in Western Canada are Paleozoic-aged stratiform deposits that occur within the limits of the tectonic sub-province of the Canadian Cordillera known as Selwyn Basin. Bounded on either side by coeval carbonate platforms. Selwyn Basin trends northwest for 1300 km from northeast British Columbia to Alaska. Paleozoic rocks of Selwyn Basin consist primarily of chert, shale and coarser-grained clastic sedimentary rocks with minor volcanic rocks.The Selwyn Basin deposits have few counterparts elsewhere in Canada, but have a close similarity in geological setting, mineralogy and morphology to well-known deposits such as McArthur (HYC) in Australia, Meggen and Rammelsberg in West Germany, and Sullivan in British Columbia. Recent studies of these deposits have led to an emerging, but now generally accepted, model of ore deposition in which stratabound zinc-lead-silver shale-hosted or ""sedimentary-exhalative"" (sedex) deposits are precipitated in active tectonic environments from metalliferous geothermal brines that rise to the sea floor along deep-seated fault zones. Although their mineralogy and ore metal zoning can be similar to that of volcanogenic massive sulphide deposits, most sedex deposits have only a weak genetic link with volcanism.Sedex mineralization in Selwyn Basin has been identified within three separate ages of shale or its metamorphosed equivalent. The lower Cambrian-age Anvil Camp in central Yukon Territory contains the only producing mine (Faro). Important lower Silurian-age zinc-lead mineralization is at Howards Pass along the Yukon - Northwest Territories border. Barite and zinc-lead-barite mineralization of upper Devonian age occurs across Selwyn Basin. Potentially economic deposits have been found at Macmillan Pass, along the Yukon - Northwest Territories border and in the Gataga District of northeastern British Columbia."

Jan 1, 1982

By X. Z. Yuan

Contamination introduced by the impurities from the feed stream can impact the PEM fuel cell performance dramatically. The presence of these unwanted trace species such as CO, H2S, NH3, can adversely affect the fuel cell functioning. It has been reported that the major impact of CO and H2S contamination on the fuel cell performance is kinetic while the effect of NH3 contamination is speculated as membrane conductivity reduction only. In this paper, a model regarding the NH3 contamination is described and the mechanism of the NH3 contamination is illuminated by the model calculations.

Jan 1, 2005