Search Documents

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By Thomas J. Ferree

"There has been a major evolution of mineral processing technology in the past decade. The evolution has been driven by recognition of broad environmental changes which have impacted various areas of the world. Numerous government regulations have required many mining and mineral processing organizations to introduce changes to reduce the undesirable effects on the environment; many mining companies have voluntarily introduced new technologies and practices which surpass the limits imposed by the regulations. Surprisingly, some of the 'new' technologies are modifications of concepts developed decades earlier. Gravity separation technology is in this category.Mineral Deposits Limited, an Australian company, has been a world leader in the development of mining concepts, reclamation practices and equipment technology that is environmentally suited to today's requirements. This paper relates to equipment used for gravity concentration and electrostatic separation systems, including Reichert cones, spirals, and electrostatic separators. The basic devices and technologies were developed more than forty-five years ago, but use of the systems was quite limited until environmental and conservation practices were recognized and introduced. Spiral concentrators, for example, were patented in the mid-l940s by I.B. Humphreys in Denver , Colorado. The two types of spirals marketed (the Model 24A for minerals and the Model 24C for coal) remained essentially unchanged until expiration of the patents. During this early period most spirals were used in iron-ore wash plants on the Mesabi Range to recover fine iron which previously had been discarded. About the same time sand mining plants in Florida incorporated spirals to recover titanium minerals and zircon from lowgrade beach sands. The Labrador Trough opened new opportunities for spirals when hard-rock iron-ore deposits were developed; approximately 10 000 Model 24A Humphreys spirals were installed between 1958 and 1966. About 5000 spirals of this model are still operating in the same capacity, in spite of the fact that extensive improvements have since been made in gravity separation technology."

Jan 1, 1993

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By P. A. Verhey

"This paper describes a series of wear-resistant ceramic materials which have been successfully used in the mineral processing industry in Canada. Applications include use with metallic ores, coal, potash and asbestos, and in other processes where wear degradation is of major concern. The paper will also deal with considerations involving the selection of the different ceramic materials available. It will cover the installation of ceramic materials on support structures under varying process ' conditions, as well as the other physical and chemical factors which have to be taken into account.IntroductionIn the mineral processing industry, large volumes of ores tailings and other materials are handled. The abrasive nature of most of these materials results in extensive wear to both handling and processing equipment.Wear ratios versus cost, production losses due to down time and wear-resistant material suitability for a given application all demand particular attention when viewed against the need for increased efficiencies in existing processes. As a consequence, a very active continuous search for materials with improved wear resistance has been carried out for many years.In this search, starting about 20 years ago, dense ceramic materials were tested and evaluated in certain applications, notably in the iron ore and asbestos operations in Eastern Canada. As a result of substantially better performance both in continuous extended life and ultimate economics realized , wear-resistant ceramic applications developed progressively in many other processing applications, replacing traditionally used materials.In the vast majority of wear-resistant ceramic applications, considerable extended life over previously used materials was established. This invariably was not just a fractional increase but, in most cases , in factors of double, triple and often all the way up to 18 and 20 times the life of alternative materials used previously. In certain applications, extended life could not be measured and appears to be indefinite.Obviously, as a result of such experiences, the progressively wider use of wear-resistant ceramic materials is now an established trend."

Jan 1, 1981

By J. L. Collins

"This paper deals with the quantitative analysis of mine maintenance records. Based on a case study of dozer engine records, the author suggests an easy method of deriving useful information for managerial decisions in a step-by-step manner.More specifically, the paper deals with the following topics:• determination of the most economical replacement time,• determination of reliability characteristics,• determination of the number of replacements, and• determination of the number of spares.IntroductionThe mining industry collects a lot of information about every aspect of its activities, an example of which appears in Table I. In Table I , the distribution describes the operating hours at failure of 56 different dozer engines used in severe applications. Besides calculating an average and possibly a standard derivation from the data, little else is derived, at least from a statistical point-of-view.More information can be obtained from these records that could help management in the decision-making process.To illustrate this point, the sample data appearing in Table I will be analyzed in detail by making use of well-known concepts in reliability engineering.Distribution of DataTable I represents a distribution obtained from the recorded hours cumulated from the operators' time cards. The operating hours have been divided into fourteen classes for each 1000 hours of engine running, e.g . all engines scoring an operating time of between 1001 and 2000 hours formed a class , those scoring between 2001 and 3000 hours another one, etc. Generally, the class interval should be a multiple of the equipment preventive maintenance check period.The minimum acceptable sample size should be large enough to ensure that the score in each class interval is at least one. Ideally, the score for each class interval should be at least five so that a chi-square test could be carried out if necessary.The average life of an engine can be found by adding the products of the frequency and the class mark (mid-point) values. Therefore:"

Jan 1, 1987

By Noel Billette, Jean-Luc Chouinard

"An analysis of the number of industrial injuries shows that the mining sector is particularly affected, since mining is one of the most dangerous industrial activities in Canada. This has led to numerous inquiries, and supports the need for an in-depth study aiming at the identification of factors responsible for these accidents. One possible factor often pointed at is the small crews incentives and this paper presents a scientific approach applied to check a potential link between bonus and accidents at two mining companies located in northwestern Quebec.The data required to do so were the accidents, the salaries and the number of hours worked at each mining site by the hourly paid personnel for the period from June 1979 to January 1982. The analysis of the results derived from the initial information shows different behaviours of the frequency rate vs the bonus rate at these mines. The number of days lost per accident is independent of the bonus rate at both mine sites, as shown by Khisquare tests on contingency tables.IntroductionA wide variety of opinions has been pinpointed by a survey of the literature related to individual or small crew incentives and industrial accidents in sectors of activity where it applies. In addition, various formulae of mining contracts take place in the industry on one part, and statistics from this sector indicate a high accident frequency rate on the other part. These fact s have lead to this scientific investigation which does isolate the direct impact of the bonus on workers' accidents. This study was undertaken with the full support of the Quebec Metal Mining Association.The conclusions of this preliminary phase of the researchproject are presented for two mining complexes in northwestern Quebec. The procedure is somewhat similar to the approach of the Belmoral Commission, with the underlying assumption that bonus has a direct impact on accidents."

Jan 1, 1986

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By Alan R. Holt

"This paper provides an overview of the use of uranium and coal in Ontario Hydro's generation program. The dynamics of available supply sources including mining and transportation infrastructures and regional considerations are described. Included is a discussion of needed procurement strategies, both in place and planned, to meet fluctuating fuel requirements while ensuring adequate supply security and cost effectiveness. IntroductionDuring the first half of this century, Ontario Hydro or the Hydro Electric Power Commission of Ontario, as it was then known substantially supplied all of the province's electricity needs from a large number of hydraulic generating stations. Although hydraulic power still provides a very significant part of Ontario energy requirements, this paper will concentrate on the role of uranium and coal in their generation program. To provide a perspective on the importance of these two fuels, Figure I shows the approximate value of each for the past few years in relation to Hydro's total operating costs. The trend toward increasing nuclear output and a corresponding decline in coal use is also clearly illustrated.Figure 2 shows the currently installed capacity of their three main energy sources, hydraulic, nuclear and coal and the 1986 production totals for each, followed by Table I which compares the average operating or running cost on the basis of dollars per megawatt hour for each type of plant. It demonstrates dramatically why Ontario Hydro base load s its hydraulic and nuclear plants, and why coal has become the swing fuel on the system. Although they have a 1200 megawatt plant in Toronto with natural gas-burning capability, and a 2000 megawatt oil-fired station near Kingston, both are presently mothballed and have not been considered in this paper.This paper starts with a user's perspective of the nuclear fuel supply situation which will be discussed in relation to the usual considerations of security, flexibility and cost."

Jan 1, 1988

By Andrew Popko

Introducing EnCana ?? A leading North American Oil and Gas company ?? Focused on natural gas and oil sands development in 12 key resource play areas across North America ?? In 2007, over 4300 wells drilled, producing about Enterprise value of approximately $50 billion ?? Invest between $5.8 Billion in 2007 ?? Over 7500 employees ?? Headquarters ? Calgary, AB

May 1, 2008

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U' Flow solids was 20%. The thickener then was allowed to cperate until the U' Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers' erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By Tobias Riedel, Peter Ay, University of Applied Sciences, Bianka Bade, Nicole Pausch, Bernhard Gemende, Florian Logsch, Matthias Leiker, Satyanarayana Narra, Claudia Glaser

This study focusses on the production of micro-structured agglomerates with high porosity from iron (III)-hydroxide-containing materials as adsorbent. A fractal-like structure of the agglomerates was created through a two-stage agglomeration process. Developing porous structures was necessary to increase the adsorption capacity. Various materials were used for the agglomeration experiments: i) filter cake (dry matter content 23 to 27 wt.-%); ii) FerroSorp®DGµ, a product which is already being used commercially for various applications in water cleaning. These materials in the pristine state have different characteristics such as dry matter content and particle size distribution. The desired optimised agglomerates can be achieved with the help of additives or binders, respectively. Additionally, the agglomeration process parameters play a vital role. In order to produce agglomerates with high porosity, the process was carried out in two steps. Firstly, FerroSorp®DGµ (d90 < 30 µm) was agglomerated jointly with the aforementioned filter cake in an Eirich intensive mixer (particle size range 125 µm < d90 < 500 µm). The second agglomeration step post drying was carried out in a pelletisation disc or in an Eirich intensive mixer with the addition of polymeric binders (up to particle sizes ranging from 2 to 4 mm). Agglomerates were characterised both in short and long term loading tests using phosphate as model ion. Contact times were less than 10 min, similar to practical application in percolation columns, or more than 7 days, respectively. The results show that the agglomerates produced in the two-stage pelletisation process have more advantageous properties like better accessibility of the active sites obtained by specificly influencing the particle size distribution during the two-stage pelletisation process.

Jan 1, 2016

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau&apos;s new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982

By Robert Boutilier

For more information on what the social licence means, see the following: Joyce, S. and Thomson, I. 2000. Earning a social licence to operate: Social acceptability and resource development in Latin America. The Canadian Mining and Metallurgical Bulletin, 93(1037) Nelson, J. and Scoble, M. 2006. Social License to Operate: Issues of Situational Analysis and Process. Vancouver, BC: Department of Mining Engineering, University of British Colombia. Thomson, I. and Boutilier, R.G. 2010. The Social License to Operate In P.Darling, (Ed.), SME Mining Engineering Handbook: Littleton, CO: Society for Mining, Metallurgy and Exploration. Much of what has been written and said about the social license to operate focuses on what the company has to do or not do. But the social license is a two-sided relationship. We also need to look at what the community has to do, or not do, in order to be capable of issuing a social license that is meaningful.

May 1, 2010

By J. G. Bensley, K. S. Detheridge

"Many plants use computers for process control and most have computerized Management Information Systems but few have been able to have these systems interact with one another. Developing this system interaction is not a one-step process but requires careful planning and implementation. This paper describes two projects that were implemented to provide the bridge between the process control and management information systems of Cominco Limited. Both projects include the replacement of essentially process control systems installed in the late 1960s. These original systems provided an enhanced level of control in the form of Direct Digital Control (via computer/manual analogue control stations) and a management reporting capability of process data. The experience gained from the use of these systems over a period of fifteen years formed a basis for the evaluation and planning for the new systems. The new systems were commissioned in 1985 and 1986 and operating and further developments leading to a totally integrated process information and control system are underway. INTRODUCTIONThe concept of hierarchical control involves a control structure consisting of a number of defined levels. Each level performs a defined function with information consolidated and combined as it moves up through the hierarchical structure. The commonly accepted structure of a hierarchical control system echoes the structure of the plant which is being controlled. Referring to Figure 1:Level 0 - Sensors and ActuatorsSensors and actuators, such as thermocouples and flow control valves, interface directly to the process and are generally connected directly to the controllers or multiplexers at Level I.Level 1 - Regulatory ControlThis level provides basic PID control (proportional/integral/ derivative) typically using microprocessor based controllers and programmable controllers for digital control of motors and machines. Systems at this levelare usually segregated by plant unit, e.g, crushing, flotation, drying. Control is concentrated on achieving optimum conditions for a particular feed rate."

Jan 1, 1989