Search Documents

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By Greg Yuriy

Over the past two decades, Vale Canada has used discrete-event simulation in a key role to support many underground mining studies. Traditionally, general purpose simulation software was developed for manufacturing and service applications. Not until recently have Mine Designers and Simulation Specialists been able to model the dynamics of underground mining scenarios without extensive manipulation of the inherent tools and entities contained within these simulation environments. This paper discusses Vale Canada?s past experiences with a variety of simulation software, describing model development methods and highlighting some of the lessons learned. The paper concludes with a review of recently considered software and provides a framework of desired attributes/functions for modeling mining scenarios.

Aug 1, 2013

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By Horace Freeman

The sulphur consumed in Canadian pulp mills and acid plants is worth approximately three million dollars annually and amounts to one hundred and fifty thousand long tons, all of which is imported from the United States. Concurrently with a decline in the value of newsprint there has been a gradual increase in the price of this raw material. Most pulp mills in Canada are situated within reasonable distance of domestic pyrite deposits; nevertheless it has not yet been found possible to mine these deposits and utilize the contained sulphur in competition with the imported material. It is the purpose of this paper to elucidate the reasons therefor, and to describe? a commercial-scale experiment undertaken with the object of introducing a native raw material into the Canadian pulp industry on the purely economic basis. Reasons for the Preferred use of Sulphur The known sulphur deposits in the United States are very large, so that at least a twenty-year supply of this material is assured. It is recovered cheaply and in pure condition. Although large deposits of pyrite are known in Canada, nothing has yet been developed to compare in size, cost of mining, or purity with the United States material. It has been necessary to handle and transport more than two tons of pyrite to equal a ton of sulphur.

Jan 1, 1930

By J. Ipinza, J. P. Ibáñez, Casas J., S. Cortés

Copper powder generated during the treatment of electro-metallurgical bleeds by reactive electro- dialysis (RED) had totally reduced the content of ferric ions in acidic synthetic electrolytes (Cu (II)- Fe (III) – H2SO4). In batch and columnar experiments 100% of the ferric ions were reduced to ferrous ions with an extremely high kinetics. A preliminary conceptual design for reducing ferric ions based on an integrate RED- Column for treatment of electro-winning bleed system is discussed. This system is able to recover simultaneously sulfuric acid and copper powder, which will reduce ferric ions. INTRODUCTION It is well known the negative effect of ferric ions in the copper electro-winning process. The increase of ferric content in the electrolyte reduces the current efficiency, i.e., there is an increase in the energy consumption, and changes the surface morphology of the copper deposit (Das, Gopala & Krishna, 1996; Vargas & Parra, 2013). The increase of the specific energy consumption due to the loss of current efficiency occurs by the reduction reaction of ferric to ferrous ions in the cathode, at the anode the ferrous ions are slowly oxidized to ferric ions (Shaw, Dreisinger, Lancaster, Richmond & Tomlinson, 2004). To control the level of iron in the electrolyte, bleeds are needed; this bleed electrolyte containing copper, sulfuric acid, cobalt, iron and other impurities normally is waster, which increased the production cost of the plant (Milbourne, 2002; Mckevitt & Dreisinger, 2009). Then, permanent efforts oriented to treat those bleeds to avoid losses of valuables components are made; among them are use ion exchange resins (Shaw et al., 2004; Mackevitt et al., 2009), chemical precipitation (Izadi, Mohebbi, Amiri & Izadi, 2017) and electrodialysis (Cortés, Ipinza & Ibáñez, 2013). The last one allows to the simultaneous recovery of sulfuric acid and copper powder. If one of the valuables obtained by treating the bleed can be used to reduce ferric ion concentration in the electrolyte could be an important asset. This issue at laboratory scale is reported in this work, the use of copper powder, generated by reactive electro-dialysis when treating synthetic acidic electro-metallurgical bleeds, for reducing ferric ions in acidic electrolytes.

Jan 1, 2019

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By Ian E. Efford

The paper gives an assessment of Canada's energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada's energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By R. Hagiwara, S. Kobayashi, K. Yasuda, T. Nohira, K. Kondo

To establish a process for the electrochemical recovery of rare earth elements from used magnet scraps, the electrochemical formation of RE-Ni alloys in molten NaCl-KCl-RECl3 salt at 973 K was investigated. Cyclic voltammetry and open-circuit potentiometry indicated the formation of several phases of RE-Ni alloys. The formation potential for each RE-Ni alloy phase was determined from the results of scanning electron microscopy and X-ray diffraction of alloy samples prepared by potentiostatic electrolysis of a Ni plate electrode at various potentials. The optimum electrolysis conditions for the separation of Nd, Dy, and Pr are discussed.

Jan 1, 2014

By A. A. Brant

Self-potential methods are based ?on measurements on the surface of voltage distributions caused by natural sub-surface oxidation phenomena. The attempt is made to. correlate voltage minima or maxima with the location of mineral materials or geological conditions which may give rise to such naturally produced spontaneous potentials. Any orebody undergoing oxidation is a source of electric current. Ground waters carrying free oxygen attack the upper surface of the body, rendering this the positive pole of a galvanic cell, with the lower portion of the body the negative pole and the surrounding weak acidic waters the electrolyte. Current flow is from positive to negative through the orebody and negative to positive through the electrolyte, i.e., through the surrounding rock. The upper end of a steeply dipping, tabular orebody is hence indicated as lying below the point on the surface where the largest negative potential is observed(l). From its basis, it is apparent that the self-potential method was developed primarily for ore exploration.

Jan 1, 1942

By R. Mariano

"The ability to optimise a concentrator from mill feed to final products requires a process simulator that integrates comminution, classification and separation stages. A key part of any such integrated process simulator is the inclusion of a model of mineral liberation in comminution to predict the particle composition distribution of the comminution products. This need was recognised by Gaudin (1939) who proposed a model of liberation based on the cubic fracture of a mineral texture composed of cubic grains of two minerals.This paper describes the development of a texture-based model of mineral liberation that builds on the method proposed by Gaudin. The approach described here, termed the JK-Gaudin Random Liberation model (JK-GRLM) uses as its basis the measured, volumetric mineral texture data that can be quantified for a given ore using X-ray micro-tomography. The textural data required as inputs for the JK-GRLM include the mineral grain size distribution. While the Gaudin model (in common with other existing liberation models) is a two-mineral (or two-phase) system, the JK-GRLM extends the approach to multimineral systems of up to 15 individual minerals, making it more widely applicable.An example of the application of the JK-GRLM to a base metal sulphide ore is provided. In the example the JK-GRLM is used to simulate the breakage of the measured ore texture and the particle composition distributions of the simulated progeny particles are compared to the measured particle composition distributions of ore that has been physically broken.The ability to calibrate this mineral liberation model with measured ore texture will allow it to be applied in greenfield situations where geometallurgical programs measure texture and in brownfield applications as a key part of integrated process simulations. The development of this model enhances our ability to simulate mineral processing operations as an integrated system."

Jan 1, 2016

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The investigated sulfide Cu-Ni ores are characterized by low PGE contents and emulgated impregnations of pentlandite and palladium minerals in the main ore-forming mineral pyrrhotite, which hinders their selective separation, requiring a collective flotation of sulfides to concentrate, and hydrometallurgical processing. As revealed by studies of floatability of Pt-Cu-Ni ore in a mixture of butyl xanthate and chelating phosphorus containing reagents, the most effective additive is Aerophine 3416 (a phosphinates mixture) manufactured by Cytec. Using collective flotation with a butyl xanthate – Aerophine 3416 composite in the ratio of 1:3 has afforded to enhance the Pt, Pd, and Ni recovery by 13.6 %, 9.2 %, and 9.4 %, respectively. The optimal ratios of Aerophine 3416 to butyl collector for the collective flotation are the following: 1:1 for Pt and Pd and 3:1 for Ni. The effect of these reagents on the electrode potential and surface hydrophobicity of pyrrhotite, pentlandite, and platinum black has been investigated. The extraction UV spectrophotometry experiments demonstrate that DIBDTPI exists on the pyrrhotite surface mainly in the form of disulfide in weak acid medium and in the form of compounds with Fe on the mineral surface in minute amounts. There appears some disulfide and few amount of (DIBDTPI)2Ni on the surface after interaction of DIBDTPI and pentlanditeINTRODUCTIONXanthates are widely used in flotation of copper-nickel ores containing platinum group metals (PGM) as sulfides collectors which can concentrate the most part of PGM connected with the sulfides. Though xanthates are hardly efficient for flotation of free PGM, the latter are floated more slowly compared to the sulfides of base metals. The reasons for poor floatation of free (mineral) forms of PGM are under-researched, however the key accepted reasons are: fine disseminations of free PGM, insufficient interaction with xanthate and negative influence of blue copperas and sulfur-containing ions which are sulfides oxidation products (Penberthy et al. 1999; Shackleton et al., 2007). That’s why an additional collector, normally dialkyldithiophosphates, is used during flotation of PGM-containing copper-nickel ores. A reagent DP-4 is used for recovery of PGM at Norilsk mining and metallurgical plant. The reagent represents a slightly-soluble organic calcium sulfonate which is given to flotation pulp in the form of water emulsion of 5% - solution in automotive diesel oil."

Jan 1, 2016

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By Martin Grenon

This paper presents two case studies where fracture set orientation was quantified using three methods: a simple fracture pole grouping, a Fisher distribution and a Kent distribution. The three fracture orientation representations were then used as inputs for kinematic slope stability analysis. Differences showed up in the probability of sliding for all instability modes considered.

Aug 1, 2013